Integra DTR-5.3 Instruction Manual page 19

Connections (DTR-6.3)
: Signal flow
6. Satellite tuner or television
(VIDEO 3)
Digital audio output
(optical)
Video output
S Video output
L (white)
Analog audio output
R (red)
5. Connecting a video cassette recorder (VIDEO 1)
Using RCA video cables, connect the video output jack (composite)
of the video cassette recorder to the VIDEO 1 VIDEO IN jack of the
DTR-6.3 and connect the video input jack of the video cassette
recorder to the VIDEO 1 VIDEO OUT jack of the DTR-6.3. Or if the
video cassette recorder has S video input and output jacks, using S
video cables, connect the S video output jack of the video cassette
recorder to the VIDEO 1 S VIDEO IN jack of the DTR-6.3 and
connect the video input jack of the video cassette recorder to the
VIDEO 1 S VIDEO OUT jack of the DTR-6.3. Or if the video
cassette recorder has component video outputs, connect them to the
COMPONENT VIDEO INPUT 1 or 2 jacks on the DTR-6.3.
With the initial settings of the DTR-6.3, the VIDEO 1 input
source is set for the COMPONENT VIDEO INPUT 2 jacks.
If you connect the video cassette recorder to the COMPONENT
VIDEO INPUT 1 jacks, this must be changed at "Input Setup" →
"Component Video" (see page 53).
Using RCA audio cables, connect the audio output jacks of the video
cassette recorder to the VIDEO 1 IN audio jacks of the DTR-6.3 and
connect the audio input jacks of the video cassette recorder to the
VIDEO 1 OUT audio jacks of the DTR-6.3. Make sure that you
properly connect the left channels to the L jacks and the right
channels to the R jacks.
With the initial settings of the DTR-6.3, nothing is allocated as
the digital input source for VIDEO 1 (----).
If you connect the digital audio output, be sure to make the appropriate
changes at "Input Setup" → "Digital Input" (see page 53).
PHONO IN
FM 75 AM
R L
ANTENNA
RS232
12 V
TRIGGER ZONE 2
OUT IR OUT LINE OUT
56K 40K ZONE 2 DC IN
OUT 24V 1A
A A
L
B
B R
ZONE 2
DIGITAL INPUT DIGITAL VIDEO 3 VIDEO 2
COAXIAL
OUTPUT IN OUT IN OUT
OPTICAL OPTICAL
2 1
COAXIAL
DIGITAL
INPUT
OUT IN IN OUT IN OUT
IN
L
SUBWOOFER
PRE OUT
R
CD TAPE VIDEO 3 VIDEO 2
6. Connecting a satellite tuner, television, or settop box
Using an RCA video cable, connect the video output jack
(composite) of the device to the VIDEO 3 VIDEO IN jack of the
DTR-6.3. Or if the device has an S video output jack, connect it to
the VIDEO 3 S VIDEO IN jack of the DTR-6.3 using an S video
cable. Or if the device has component video outputs, connect them to
the COMPONENT VIDEO INPUT 1 or 2 jacks on the DTR-6.3.
With the initial settings of the DTR-6.3, the VIDEO 3 input
source is set for the COMPONENT VIDEO INPUT 2 jacks.
If you connect the device to the COMPONENT VIDEO INPUT 1
jacks, this must be changed at "Input Setup" → "Component Video"
(see page 53).
Using an RCA audio cable, connect the audio output jack of the
device to the VIDEO 3 IN audio jacks of the DTR-6.3. Make sure
that you properly connect the left channel to the L jack and the right
channel to the R jack.
If the device has a digital output, connect it to either the DIGITAL
INPUT COAXIAL jack or the DIGITAL INPUT OPTICAL jack of
the DTR-6.3 depending on the type of connector on the device.
With the initial settings of the DTR-6.3, the VIDEO 3 input source is
set for digital input at the OPTICAL 2 jack (OPT 2).
If the digital connection is made at a different jack, this must be
changed at "Input Setup" → "Digital Input" (see page 53).
Y
P
P
GND
COMPONENT VIDEO
INPUT 2 INPUT 1 OUTPUT
Y
P
B
REMOT
CONTRO
P
R
VIDEO 1 DVD MONITOR
IR
IN IN OUT
OU
V
I
S
IN FRONT SURR CENTER
L
R
SUB
VIDEO 1
WOOFER
DVD
L (white)
R (red)
L (white)
R (red)
(VIDEO 3)
Component video output
B
R
Video output
S video output
5. VCR (VIDEO 1)
Video input
S video input
Analog audio output
Analog audio input
19