Information provided in this manual is intended to be accurate and reliable. However, Chenbro Micom Co., Ltd., assumes no responsibility for its use, nor for any infringements upon the rights of third parties, which may result from its use. Technical Support Chenbro works hard to offer our customers maximum performance from our chassis.
ES34069 Chassis User’s Manual Rev. A1 Accessory Pack Screw Pack for IDE / SATA Slim ODD Cable Tie (1) Front Bezel Key (1) M/B (1) Adaptor (1) Power Cable, Big 4P Screw Pack for Active Heatsink for PCI Add-on Card...
ES34069 Chassis User’s Manual Rev. A1 Features Ideal for high storage capacity (Hot-swap HDDs) with RAID-5 functionality Available for multi-media platform 9.5 liters small form factor with Mini-ITX M/B Removable M/B carrier for excellent thermal performance & easy cabling External adapter reduces noise level Optional remote control &...
ES34069 Chassis User’s Manual Rev. A1 Opening the Chassis Overview Side Panel w/Venting Slim CD-ROM Carrier Main Cable Through Hole (Optional) w/Rubber pad Front Bezel (w/Key Lock) Intrusion Switch USB & Front Control Cables Motherboard Cage Front Card Reader (Optional)
ES34069 Chassis User’s Manual Rev. A1 To open the chassis for assembly of internal parts, users need to: Remove the side panel Remove the front bezel Side Panel Removal ■ Release the side panel thumb screw on the rear ■ Push and slide the side panel toward rear to open the...
ES34069 Chassis User’s Manual Rev. A1 Motherboard Cage Removal ■ Release two secure screws on the M/B cage ■ Release two screws around the rear fans ■ Remove the motherboard cage ■ Disconnect the extension fan cables ■ Detach the motherboard cage with System Cables ■...
ES34069 Chassis User’s Manual Rev. A1 ■ Slide the assembled CD-ROM into the chassis ■ Make sure the holder latch is secured when fully seated Installing 3.5” SATA-II Hard Drive ■ Remove the HDD Carrier from the chassis and place ■...
ES34069 Chassis User’s Manual Rev. A1 Installing Card Reader ■ Detach the front screw of Card Reader holder ■ Pull out the Card Reader holder ■ Remove the seal on the holder and make sure the ■ Attach screws to fix the Card Reader sockets is right to the opening ■...
ES34069 Chassis User’s Manual Rev. A1 Installing Dedicated AMD / Intel Heatsink The Chenbro heatsink for ES34069 is designed specifically to support Intel and AMD desktop LV (Low Voltage) CPU in universally. Note the CPU power rating should not over 65W as maximum.
ES34069 Chassis User’s Manual Rev. A1 Installing Riser Card ■ The PCI card mounting bracket must be detach and ■ Connect the cables before install. use special one for mounting, (Ex. PCI RAID card) ■ Install the PCI card with riser into the slot gently.
ES34069 Chassis User’s Manual Rev. A1 Connecting Devices ES34069 is pre-installed with several cables inside as factory default, which includes: SATA-II cable for Hot-swap hard drive Power cable for M/B Front panel I/O cables USB 2.0 cable 4-in-1 card reader Connecting SATA-II Cables ■...
ES34069 Chassis User’s Manual Rev. A1 Connecting Front Panel I/O and LEDs a. USB 2.0 cable connection ■ Front USB cable should be connected to on-board USB header properly depends on different M/B. b. Front display cable connection ■ The fan-out cable with different connection for: ■...
Page 17
■ Use either standard IDE / SATA cable from 3 party of DC harness, small 4P is connected to the Slim M/B, or use optional cable from Chenbro to connect ODD adaptor board to the Slim ODD adaptor board e. Cable management ■...
ES34069 Chassis User’s Manual Rev. A1 Power Adaptor and Backplane Power Adaptor Specification: For electrical specification: Input Characteristics Output Characteristics Item Spec Item Spec Rated Input Voltage 100V / 240V Output Raged Voltage Input Voltage Range 90VAC to 264VAC Output Current 6.32A...
Rev. A1 Power Distribution Board The PDB (Power Distribution Board) inside the ES34069 is a specific DC to DC adaptor, which only provides the converting from DC19V to multiple voltages include +5V, +3.3V and +12V for all the devices and boards usage scale up to 180W Power Adaptor. As the...
Rev. A1 2-port SATA-II Backplane Introduction ES34069 is integrated with two SATA-II backplanes to support four 3.5” HDD hot-swap feature. With dedicate backplane bracket assembled, users can directly attach the HDD on the tray and plug into the HDD slot.
Need help?
Do you have a question about the ES34069 and is the answer not in the manual?
Questions and answers