Main Control Panel Buttons And Display - HotSpring LANDMARK Owner's Manual

LOCK OVERRIDE
The Lock Override feature is for spa users who normally keep the set temperature locked. Should the user wish to lock all
spa controls temporarily, the spa lock can be applied over an already-applied temperature lock. Then, when the spa lock is
removed, the temperature lock will remain on, to prevent unwanted tampering with the set temperature.

MAIN CONTROL PANEL BUTTONS AND DISPLAY

The main control panel has buttons which the spa user presses to set the temperature, initiate the clean cycle, vary the
intensity of the light, and activate or deactivate the jet pump. With the exception of the Clean button, the control panel
display responds to let you know you've pressed a button, and that the selected function has been performed. After a
period of non-use, pressing any button will wake up a sleeping display, as well as performing its function.
TEMPERATURE CONTROL
The set temperature range is from 80°F to 104°F. Higher temperatures can be reached by using one of four codes: ut1, ut2,
ut3 and ut4. These settings get progressively warmer, with ut4 the highest at approximately 106°F. (The temperature of any
setting may rise slightly depending on the current use and condition of your spa, and on outside temperature.)
To increase the set temperature of the spa water, press the Temp Plus (+) button. Each time the button is pressed, the set
temperature display will increment by one degree. If the button is held down, the set temperature display will increase by
one degree every half-second.
To decrease the set temperature of the spa water, press the Temp Minus (-) button. Each time the button is pressed, the
set temperature display will decrement by one degree. If the button is held down, the set temperature display will decrease
by one degree every half-second.
If the set temperature value will not change, check the Temp Lock and Spa Lock features. When either of these features is
applied, the temperature control is disabled.
JETS CONTROL
There are two buttons (three buttons on Grandee
The Clean button, provided as a convenient timer for water maintenance, activates the jet pump for a ten minute period.
The Clean indicator will turn on and the Jet symbol on the display will illuminate to indicate the jet pump is engaged. Next
x Operating Instructions
Temp Plus (+) buttons at the same time and hold them down until the
words SET TEMP, the numerical set temperature value and the lock symbol are
illuminated on the display (approximately 2 seconds).
When the Temperature Lock is activated, the Jets, Light, and Clean buttons will
operate normally, and the temperature setting can be viewed but can NOT be
changed. If a temperature button is pressed, the control panel will display the
lock symbol and the set temperature for 30 seconds, then turn off.
To deactivate the Temperature Lock, press the Light Plus (+) and Temp Plus (+) buttons at the
same time and hold them down until the lock symbol is no longer illuminated on the display
(approximately 2 seconds).
The set temperature of the spa water will automatically be 102°F the first time that power is
applied. This is the setting programmed at the factory. After the spa has been set up and
used, the last temperature value set by the user will be stored in memory. If power is
disconnected from the spa, it will automatically revert to the last set temperature when
power is reapplied.
To display the set temperature of the spa, press the Temp Plus (+) button. The set
®
The JETS button (all models) / JETS 1 (Grandee
activates the jet pump. When the Jets or Jets 1 button is pressed, the jets symbol will
illuminate on the control panel display. The symbol will remain lit until the button is
pressed to turn off the jet pump, or after two hours of continuous operation when the pump
is automatically shut off by the control system.
The JETS 2 button (Grandee
the Jets 2 button is pressed, the jets symbol will illuminate on the control panel display. The
symbol will remain lit until the button is pressed to turn off the jet pump, or after two hours of
continuous operation when the pump is automatically shut off by the control system.
Page 26 Page x
To activate the Temperature Lock, press the Light Plus (+) and
temperature will be displayed, unless the spa is locked (in which case
the word SPA is displayed with the lock symbol). The set temperature
display will automatically shut off after 30 seconds.
®
and Landmark models) which affect the jet pump(s):
® ®
and Landmark only) activates the second jet pump. When
® ®
and Landmark models only)