Operating Instructions; Spa Control Panel; System Mode; Cleaning Mode - HotSpring HOT SPOT RELAY Owner's Manual

o I
peratInG nStructIonS

SPA CONTROL PANEL

Your control panel consists of an LCD display and convenient touch
pads that allow you to set the water temperature and adjust the skim/
filter cycle settings, lock spa temp, lock all spa functions, as well as
control the hydrotherapy jets, and lights.
LCD DISPLAY INVERSION
You may invert the control panel display for easier viewing from inside
the spa. To invert the display the following is required: Press the
MODE() and (-) buttons simultaneously. By pressing the MODE()
and (-) buttons simultaneously a second time the screen will go back to
it's original display.
Filter Cycle 2

Mode
Icon
Filter Cycle
1 Icon

Mode
Temperature
Jet Icon
Up /On
Temperature
Down/Off
MODE BUTTON
From the Home screen use the MODE ( or ) button to scroll to the
System, Clean, Audio (if your spa is equipped) and Tools screen. Press
READY READY
SET SET the (+) button to enter into the sub screens. POWER POWER
F1 F1
F2 F2
TEMPERATURE CONTROL
The set temperature range is from 80°F (26°C)
POWER POWER
POWER POWER READY READY
to 104°F (40°C). Temperatures of any setting
may rise slightly depending on the current
use and condition of your spa, and on outside
temperature. Whenever power is disconnected
POWER POWER READY READY POWER POWER
and then reconnected to the spa, the water temperature setting will
automatically return to the last temperature entered into the program.
To increase the set temperature, press the (+) button, once for each
degree of increase temperature desired. If you hold the (+) button down,
the set temperature will increase by one degree every half second.
SET SET
F1 F1
To decrease the set temperature, press the (-) button, once for each
F2 F2
degree of decreased temperature desired. If you hold the (-) button down, the
set temperature will decrease by one degree every half second.
POWER POWER READY READY
JET PUMP CONTROL
Pressing the JET button for the RELAY & RHYTHM
changes the jet pump functions, depending on the
number of presses:
• 1st press: Two-speed jet pump runs on low speed
• 2nd press: Two-speed jet pump runs on high speed
Power Icon
Temp Ready
Icon
Sleep
Icon
Filter Cycle Icon
Light Icon
READY READY
POWER POWER
SET SET
F1 F1
F2 F2
F1 F1
F2 F2
READY READY
POWER POWER
READY READY
POWER POWER
F1 F1
SET SET
F1 F1
F2 F2
POWER POWER READY READY
F1 F1
POWER POWER
F2 F2
• 3rd press:
• 4th press:
• 5th press:
Pressing the JET button for the PACE changes the jet pump functions, depending
on the number of presses:
• 1st press:
• 2nd press:
• 3rd press:
LIGHT - ON/OFF & INTENSITY CONTROLS
The light control uses four positions: High, Medium, Low, and Off. To
turn on the spa light, press the LIGHT button. This will place all lights
in the spa in the High, or maximum intensity position. When the lights
turn on, the light symbol will also illuminate on the control panel display.
Press the LIGHT button again to lower the intensity of the lights to the
Medium position. Press the LIGHT button again to lower the intensity
Jets Button
even more, placing the lights intensity in the Low position. Press the
LIGHT button one more time to shut the lights off. When the lights are
deactivated, the light symbol will also turn off.
If the lights are left on, they will automatically be turned off by the control
system after 6 hours of continuous operation. The light symbol on the
panel will also turn off when the lights are deactivated.
If the lights will not turn on, make sure SPA LOCK is deactivated. SPA
LOCK disables all the controls on the control panel (see following pages
for more information on SPA LOCK).

SYSTEM MODE

Light Button
Your spa is equipped with a System Mode. This function will allow you
to conveniently turn the jet(s) on high speed and the lights on maximum
intensity at the same time.
To activate the System Mode, perform the following functions:
Press the MODE ( or ) button until
SYSON is displayed on the screen. Press
the (+) b utton to activate the SYSON mode
READY READY
feature. The jets and light icons will remain
READY READY
POWER POWER READY READY
illuminated on the display until the system
mode is deactivated.
READY READY
NOTE: Once activated, the jet and light functions can still be changed
POWER POWER by pressing the JETS or LIGHT button. READY READY
READY READY
To deactivate the System Mode, press the MODE ( or ) button until
the SYSON symbol is displayed on the screen. Press the (-) b utton to
READY READY
deactivate.
READY READY
READY READY POWER POWER

CLEANING MODE

All spas are equipped with a "Cleaning" mode. When the mode is
READY READY
activated, the jet pump in the first jet system will turn on and run for ten
SET SET
minutes (used for water maintenance). To activate the "Cleaning" mode,
F1 F1
press the MODE ( or ) button several times until the CLEAN menu
F2 F2
is displayed. Press the (+) b utton to activate the CLEAN mode feature.
NOTE: The jet icon will flash on and off while
the "Cleaning " mode is active.
POWER POWER
READY READY
To stop the Cleaning Cycle before the ten
F1 F1
F2 F2
minutes is complete, Press the MODE ( or
) button several times until the CLEAN menu
is displayed on the screen then press the (-) b utton to deactivate.
NOTE: Pressing the JETS button will also deactivate the clean cycle
and the jet icon will remain on and solid.
Page 14
One and Two-speed jet pumps run on high speed
One-speed jet pump runs on high speed
Both jet pumps are off
Two-speed jet pump runs on low speed
Two-speed jet pump runs on high speed
Jet pump is off
POWER POWER READY READY
F1 F1
F2 F2
READY READY
READY READY
F1 F1
READY READY
SET SET
F1 F1
F2 F2
READY READY

Operating Instructions