Operating Instructions; Main Control Panel - HotSpring Grandee GG Owner's Manual

o I
peratInG nStructIonS
®
All Hot Spring spa models are equipped with a main control panel,
located on the front top of the spa, some models have an auxiliary
control panel.
The main control uses led indicator lights and an integrated lcd
display to operate all spa functions.
The auxiliary control panel is located so that a bather in the spa can
operate the light or the jets. If the SPA lock function has been
initiated at the main control panel, the auxiliary control panel will not
operate.

MAIN CONTROl PANEl

The main control panel provides a quick visual check of the spa's
status and allows the user to set the temperature, activate the jets
& lights, lock the temperature and/or spa functions. other optional
functions may also be available depending on the spa model and
accessory equipment that has been installed into the spa. The main
control panel has eight buttons.
JeTs
Hard button soft buttons
Indicator lights
opTIon
Hard button
Control panel screen
HARd BuTToNS
The four labeled outer buttons are referred to as "Hard buttons".
These buttons are fixed and their functions do not change.
JeTs - If jet pump indicator light is off and JeTS hard button is
pressed, the 1st jet pump function will activate and the main control
panel display will advance to the Jets menu.
If jet pump indicator light is on and the JeTS hard button is pressed
while in any screen other than the Jets menu, the jets pump function
does not change, only the main panel screen will change to the Jets
menu.
lIGHTs - If lights are off, press lIgHTS hard button from any screen
to turn on the underwater lights (only) and display the underwater
lighting menu. When lIgHTS hard button is pressed in the
underwater lighting menu with the underwater lights on, it will cycle
the light intensity for the underwater lights. If underwater lights are on,
initial press of lIgHTS hard button will not change light setting but will
access underwater lighting menu.
opTIons - Transitions to the options screen to access temperature
and setup menu
lIGHTs
Hard button
baCK
Hard button
Page 12
baCK - goes back one menu. In Home screen Hold BAck button until
screen rotates 180° to view from inside spa. Repeat to reverse.
SoFT BuTToNS
The four inside buttons are referred to as "soft buttons". Pressing a
soft button will activate the function on the control panel screen closest
that button. The control panel displays let you know you've pressed
a button and that the selected function has been performed. After a
period of non-use (45 seconds) the display will go back to the Home
screen where the screen will remain on for several minutes before
going to the sleep mode. Pressing any button will wake up a sleeping
display.
INdIcAToR lIgHTS
At a glance, the indicator lights are visible on the main control panel.
The seven led indicator lights work independently from the rest of the
control panel display. They remain lit so that you may know the status
of your spa at a glance.
ready Indicator: The ReAdy indicator will light when the
spa water temperature is within 2°F (1°c) of the set
temperature, and will turn off when the temperature is outside of that
range. If you increase or decrease the temperature setting of the spa,
the ready indicator will turn off until the water temperature reaches the
acceptable range for the new temperature setting. A flashing ReAdy
indicator means a problem may exists with the temperature sensor
(see Troubleshooting section for more information)
spa light Indicator: The Spa light indicator is lit when any
light inside the spa is on. The indicator light will remain solid
as long as any light is activated. Spa light indicator does not flash.
spa or Temperature lock Indicator: The Spa or
Temperature lock indicator is lit when either the Spa lock,
Temperature lock or both is activated. lock indicator does not flash.
Jet pump Indicator: The Jet Pump indicator is lit whenever a
jet pump is on. The Jet Pump indicator will flash whenever
the spa is in the ten-minute clean cycle.
summer Timer Indicator: The Summer Timer indicator is lit
when the summer timer is set to oN. In the summer timer
mode, the heater and circulation pump cycle are off for eight hours.
The Summer Timer indicator will not flash.
Water Care Indicator: The Water care indicator is lit
whenever a water care device is detected in the system and
the water care system is operating correctly. The icon will flash if the
water care system requires attention.
poWer Indicator: The PoWeR indicator is 'on' when the
spa is properly supplied with power. It also provides a
diagnostic function–a flashing power indicator indicates that the heater
high limit has tripped, meaning that either the spa water is above its
acceptable temperature range, or a malfunction has occurred within
the spa (such as low circulation due to clogged filters). An 'off' power
indicator means that there is a problem with the spa control box or the
power supplied to the spa (see Troubleshooting section for more
information).

operating Instructions