Main Control Panel Buttons And Display - HotSpring Landmark Owner's Manual

LOCK OVERRIDE
The Lock Override feature is for spa users who normally keep the set temperature locked. Should the user wish to lock all spa controls
temporarily, the spa lock can be applied over an already-applied temperature lock. Then, when the spa lock is removed, the temperature lock will
remain on, to prevent unwanted tampering with the set temperature.

MAIN CONTROL PANEL BUTTONS AND DISPLAY

The main control panel has buttons which the spa user presses to set the temperature, initiate the clean cycle, vary the intensity of the light, and
activate or deactivate the jet pump. With the exception of the CLEAN button, the control panel display responds to let you know you've pressed a
button, and that the selected function has been performed. After a period of non-use, pressing any button will wake up a sleeping display, as well
as performing its function.
TEMPERATURE CONTROL
The set temperature range is from 80°F to 104°F. The set temperature of the spa water will automatically be 102°F the first time that power is
applied. This is the setting programmed at the factory. After the spa has been set up and used, the last temperature value set by the user will be
display will increment by one degree. If the button is held down, the set temperature display will increase by one degree every half-second.
To decrease the set temperature of the spa water, press the TEMP minus (-) button. Each time the button is pressed, the set temperature display
will decrement by one degree. If the button is held down, the set temperature display will decrease by one degree every half-second.
If the set temperature value will not change, check the TEMP LOCK and SPA LOCK features. When either of these features is applied, the
temperature control is disabled.
JETS CONTROL
There are two buttons (three buttons on Landmark
The JETS button (all models) / JETS 1 (Landmark
display will illuminate to indicate the jet pump is engaged. Next you may add properly measured spa water chemicals into the filter compartment.
The jet pump and clean indicator will automatically shut off after ten minutes.
If the jet pump will not engage, make sure SPA LOCK is deactivated. SPA LOCK disables the controls on both the main and auxiliary control
panels.
Operating Instructions
the words SET TEMP, the numerical set temperature value and the lock symbol are
illuminated on the display (approximately two seconds).
When the TEMPERATURE LOCK is activated, the JETS, LIGHT, and CLEAN
buttons will operate normally, and the temperature setting can be viewed but
can NOT be changed. If a temperature button is pressed, the control panel will
display the lock symbol and the set temperature for 30 seconds, then turn
off.
To deactivate the TEMPERATURE LOCK, press the LIGHT plus (+) and TEMP plus (+)
buttons at the same time and hold them down until the lock symbol is no longer illuminated on the
display (approximately two seconds).
stored in memory. If power is disconnected from the spa, it will automatically revert to the
last set temperature when power is reapplied.
To display the set temperature of the spa, press the TEMP plus (+) button. The set
temperature will be displayed, unless the spa is locked (in which case the word SPA is
displayed with the lock symbol). The set temperature display will automatically shut
off after 30 seconds.
® ®
and Grandee models) which affect the jet pump(s):
® ®
and Grandee models only) activates the jet pump. When the JETS or JETS 1 button is
pressed, the jets symbol will illuminate on the control panel display. The symbol will
remain lit until the button is pressed to turn off the jet pump, or after two hours of
continuous operation when the pump is automatically shut off by the control system.
The JETS 2 button (Landmark
the JETS 2 button is pressed, the jets symbol will illuminate on the control panel display. The
symbol will remain lit until the button is pressed to turn off the jet pump, or after two hours of
continuous operation when the pump is automatically shut off by the control system.
The CLEAN button, provided as a convenient timer for water maintenance, activates the jet
pump for a ten minute period. The CLEAN indicator will turn on and the JET symbol on the
Page 35
To activate the TEMPERATURE LOCK, press the LIGHT plus (+)
and TEMP plus (+) buttons at the same time and hold them down until
To increase the set temperature of the spa water, press the TEMP plus
(+) button. Each time the button is pressed, the set temperature
® ®
and Grandee only) activates the second jet pump. When