Smartjet ® System; Comfort Control System; Jets; Moto-Massage Jet - HotSpring LANDMARK Owner's Manual

IMPORTANT: Be sure the air control valves are open by turning each one clockwise (to the right) and check to see
®
that the SmartJet Lever is pointing to the 9 o'clock position (see illustration in SmartJet
SERVICE NOTES: If there is a large pocket of air trapped in the circulation pump plumbing after filling the spa with
water, the heater thermal cut-off may trip when the heater is energized. The air lock will eventually cause the circulation
pump's thermal overload to trip and shut down the pump as well. The circulation pump will start up automatically once
it has cooled. You'll need to remove the air lock and reset the heater thermal cut-off. See the Service Information
section for details.
Weak or surging jets are an indication of a low water level condition or clogged filter cartridges.
4. Adjust Total Alkalinity (TA), Calcium Hardness (CH), then spa water pH and finally sanitize the spa water following the
procedures listed in the Water Quality and Maintenance section. The jet button marked "Clean" should be used for the
10 minute "super-chlorination" or "shock treatment."
OPERATION NOTE: Make sure you adjust your Total Alkalinity first, as an out-of-balance condition will affect your
ability to adjust the pH correctly, and will prevent the sanitizer from operating effectively.
5. Once the spa plumbing and pumps have been primed, the water sanitized, and the jet pump has shut off, the cover
may be put on the spa. Always secure the cover in place using the cover coverlocks whenever the spa is not being
used.
6. The spa temperature is pre-programmed to reach 102°F, and will normally do so within 18 to 24 hours. You may raise
the water temperature by pressing the TEMP (+) button on the control panel, or lower it by pressing the TEMP (-)
button. After a few hours to heat or cool, the water temperature will remain within 1-1/2 degrees of your selected
temperature. To prevent tampering, you can lock your desired temperature setting. Refer to the Control Panel section
for details.
®
SMARTJET SYSTEM
®
With your Hot Spring Spa's exclusive SmartJet
of your spa. Using the SmartJet
® ®
On the Grandee , Landmark , and Jetsetter
To access a jet system, simply turn the SmartJet
® ®
the Classic , Sovereign , and Prodigy
jet systems. The jet systems are selected by turning the SmartJet
position (facing the spa). Please consult the jet system menus on the following pages to determine which
jets are activated with each SmartJet
COMFORT CONTROL
®
The Comfort Control system allows you to control the intensity of the massage at each jet
by adjusting the mixture of air and water. Jets with an adjustable faceplate are controlled by
turning the faceplate clockwise for a stronger flow, counterclockwise for a softer flow. Jets
without an adjustable faceplate are controlled by a Comfort Control
Jets are controlled by Dark Teal, Forest Green or Blue Comfort Control
®
Massage Jet is controlled by Seafoam Green or Light Gray Comfort Control
®
JetStream Jet is controlled by a Steel Blue or Dark Gray lever.
NOTE: The intensity of the JetStream
®
Turn the Comfort Control lever clockwise to increase the intensity of the jet and counterclockwise to
decrease the intensity.

JETS

MOTO-MASSAGE
®
The Moto-Massage Jet automatically travels up and down in a sweeping motion, simulating the natural stroking effects of
a manual massage. The intensity and speed of the Moto-Massage
lever with the Seafoam Green or Light Gray dot.
®
The Moto-Massage Jet has been factory adjusted to provide maximum hydromassage, and to achieve full vertical travel
®
with its Comfort Control lever in the full air volume position. Should the Moto-Massage
and the problem is not a closed air control valve or clogged filter cartridge, then your Hot Spring
should be contacted.
®
System, you can control the massaging action
®
lever, the jets are activated in sets, known as jet systems.
® ®
, each SmartJet lever controls two jet systems.
®
lever to the 3 o'clock or 9 o'clock position. On
® ®
, the single SmartJet lever has four positions to access the four
®
lever position. Or just jump in and play–turn the lever(s) and see what happens.
®
SYSTEM
®
Jets in the footwell can not be altered.
® JET
(Not available on Prodigy
®
System section).
9 o'clock
®
lever to the 3, 6, 9 or 12 o'clock
® ™
lever. The Precision
®
levers. The Moto-
®
levers. The
®
)
®
Jet may be adjusted by turning the Comfort Control
®
Jet not achieve full vertical travel
®
Page 17
12 o'clock
6 o'clock
Dot color indicates which jets are controlled
Increase Air
Volume
®
Spa service center
Operating Instructions
3 o'clock
Decrease Air
Volume