Table of Contents
Advertisement
The Grandee
system separately, or both halves simultaneously. Each half of the jet system has two different jet menus which are
selected by the individual SmartJet
menus when using the spa.
The Grandee
system consists of a 6,000 watt (6 kW) heater, an energy efficient low-flow circulation pump, and a high limit thermostat
and heater thermal cut-off for protection of user and equipment.
In each of these spas, the heater will turn on while the jet pump is operating (after a 1-1/2 degree temperature drop) to help
maintain the water temperature during spa use. Factors such as the number of people using the spa, the air temperature
and the length of time the pump is operated will affect the heating system's ability to maintain the water temperature.
115/230 VOLT CONVERTIBLE MODELS
• Classic
• Sovereign
The 115 / 230 volt convertible Hot Spring
GFCI plug at the end of a cord. The GFCI plug contains a GFCI breaker for user and equipment protection. The 115 volt
configuration requires a dedicated outlet to supply power to the spa.
These models can be converted to 230 volt operation with the addition of a subpanel and a control box wiring change.
Consult your dealer before attempting to convert from 115 volt operation to 230 volt operation. Any damage to the spa
from improper conversion is not covered under the warranty.
In the 115 volt configuration, either the heater or the jet pump can operate, but they can't work at the same time. In a 115
volt system, as long as the jet pump is activated, the heater will not turn on. On the other hand, when the spa is converted
to operate in the 230 volt configuration, the heater and jet pump can operate simultaneously.
Each convertible spa model is equipped with a No-Fault
operate at 1500 watts when the spa is configured as a 115 volt cord-and-plug connected model and at 6000 watts when
the spa is configured as a 230 volt converted model. The heating system consists of the No-Fault
efficient low-flow circulation pump, and a high limit thermostat and heater thermal cut-off for user and equipment
protection.
All four of these models feature a Wavemaster
®
Prodigy
models use the 1.65 HP Wavemaster
®
SmartJet
START-UP PROCEDURES
The water level of your Hot Spring
CAUTIONS:
• Do not fill the spa with hot water, as tripping of the high limit thermostat may result.
• Do not connect power to an empty spa.
• Before using your spa after filling, "super-chlorinate" or "shock" the spa water to ensure all bacteria and
contaminants have been oxidized. See the Water Quality and Maintenance section.
1. Close all drains and fill the spa with water through the filter compartment.
HINT: Use the FreshStart
and Maintenance section for additional information.
NOTE: Watkins Manufacturing Corporation does not recommend the spa be filled with "softened" water, as this may
damage the spa's equipment.
2. Once the spa has been filled with water and the equipment compartment door is secured, power must be applied to
the spa:
115 Volt Models - Connect the GFCI to the waterproof receptacle.
230 Volt Models - Open the door of the electrical subpanel and reset the two GFCI breakers. Close and secure the
subpanel door.
3. The jet pump(s), heating system, and all internal plumbing will prime automatically as the spa is filled with water. To
check the operation of the jet system and purge any remaining air from the heating system, push in the Jets button
(Jets 1 button, also the Jets 2 button for the Grandee
fully operational (as indicated by strong, non-surging jets), priming of the spa is complete.
Operating Instructions
®
®
's and Landmark
's dual 1.65 HP Wavemaster
®
levers. This feature allows you to select any one of four menus or a combination of
®
®
and Landmark
are equipped with a No-Fault
(Model F)
• Prodigy
®
(Model I)
• Jetsetter
®
®
lever is used to operate the jet menus available in these models.
®
Spa should be maintained approximately four inches below the top of the spa.
™
Pre-filter to remove unwanted contaminants from the tap water. See the Water Quality
10,000
Page 16
™
7000 jet pumps allow you to operate each half of the jet
®
6000 stainless steel, high watt density heater. The heating
(Model H)
®
(Model J)
®
Spa models come configured with a familiar 115 volt electrical system, with a
®
6000 stainless steel, high watt density heater. The heater will
™
jet pump to operate their jet systems. The Classic
™
®
7000, while the Jetsetter
®
®
and Landmark
®
6000 heater, an energy-
®
, Sovereign
spa uses the 1.5 HP Wavemaster
) and wait one minute. Once the jet system is
®
and
™
5000. The
Hide quick links:
Advertisement
Table of Contents
