Page 2
Their expertise will facilitate the enjoyment of your new Hot Spring spa. The serial number label is located within the equipment compartment of your Hot Spring spa. IMPORTANT: Watkins Manufacturing Corporation reserves the right to change specifications, or design, without notification and without incurring any obligation.
IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS AVOIDING THE RISK TO CHILDREN DANGER: • RISK OF CHILD DROWNING. Extreme caution must be exercised to prevent unauthorized access by children. To avoid accidents, ensure that children cannot use a spa unless they are supervised at all times. WARNING: •...
• Your spa uses ground fault circuit interrupters in the electrical subpanel. Before each use of the spa and with the unit operating, push the TEST button on each breaker. The switch should click over to the “Trip” position. Wait 30 seconds and reset each GFCI breaker by switching it completely off and then completely on.
AVOIDING THE RISK OF HYPERTHERMIA Prolonged immersion in hot water can result in HYPERTHERMIA, a dangerous condition which occurs when the internal temperature of the body reaches a level above normal 98.6°F (37°C). The symptoms of hyperthermia include unawareness of impending hazard, failure to perceive heat, failure to recognize the need to exit the spa, physical inability to exit the spa, fetal damage in pregnant women, and unconsciousness resulting in a danger of drowning.
Single phase GFCI protected circuit CAUTION: Watkins Manufacturing Corporation suggests a structural engineer or contractor be consulted before the spa is placed on an elevated deck. * NOTE: The “Filled weight” and “Dead weight” of the spa includes the weight of the occupants (assuming an average occupant weight of 175 lbs).
• If your spa is going to be installed in a location known to be frequented by mice, rats or other nocturnal creatures, Watkins Manufacturing Corporation recommends covering the access opening to the spa’s equipment compartment with a heavy gauge screen material available at your local hardware store.
4”- (10.1 cm) thick concrete pad or structurally engineered deck and NOT shimmed in any manner. WARNING: Watkins Manufacturing Corporation recommends that a structural engineer or contractor be consulted prior to placing the spa on an elevated deck, or platform. Use the Dead Weight in the Spa Specification chart to determine the structure’s requirements.
Page 10
™ ENVOY (MODEL KK) Leveling Points NOTE: All dimensions are approximate; measure your spa before making critical design or pathway decisions. 44 1/2" (113.0cm) 44 1/2" (113.0cm) 18" (45.7cm) 18" (45.7cm) 93" (236.2 cm) • 15 leveling points (place shims approx. 18” in from edge, then center middle shims). Page 7 Installation Instructions...
Page 11
® VANGUARD (MODEL V & VV) Leveling Points NOTE: All dimensions are approximate; measure your spa before making critical design or pathway decisions. 87" (221cm) 43 1/2" (110.5cm) 43 1/2" (110.5cm) 18" (45.7cm) 18" (45.7cm) • 15 leveling points (place shims approx. 18” in from edge, then center middle shims). Page 8 Installation Instructions...
Page 12
® SOVEREIGN (MODEL I & II ) Leveling Points NOTE: All dimensions are approximate; measure your spa before making critical design or pathway decisions. • 15 leveling points (place shims approx. 18” in from edge, then center middle shims). Page 9 Installation Instructions...
Page 13
™ ACCOLADE (MODEL AC) Leveling Points NOTE: All dimensions are approximate; measure your spa before making critical design or pathway decisions. 41 3/8" (105.0cm) 41 3/8" (105.0cm) 18" (45.7cm) 18" (45.7cm) 87" (220 cm) • 15 leveling points (place shims approx. 18” in from edge, then center middle shims). Page 10 Installation Instructions...
Page 14
® PRODIGY (MODEL H) Leveling Points NOTE: All dimensions are approximate; measure your spa before making critical design or pathway decisions. • 10 leveling points (place shims approx. 15” in from edge, then center middle shims). Page 11 Installation Instructions...
Page 15
® JETSETTER (MODEL J) Leveling Points NOTE: All dimensions are approximate; measure your spa before making critical design or pathway decisions. • 10 leveling points (place shims approx. 15” in from edge, then center middle shims). Page 12 Installation Instructions...
® VISTA (MODEL SS) OVERHEAD VIEW ® A. SmartJet system lever ® B. Moto-Massage jet Comfort ® Control system lever ® C. Precision jets Comfort Control system lever D. Water feature lever E. Hydromassage jet with directional nozzle F. Hydromassage jet with rotary nozzle ®...
® GRANDEE (MODEL G) OVERHEAD VIEW ® A. SmartJet system lever ® B. Moto-Massage jet Comfort ® Control system lever ® C. Precision jets Comfort Control system lever ® D. JetStream jet Comfort Control system lever E. Pillow F. Hydromassage jet with directional nozzle G.
™ ENVOY (MODEL KK) OVERHEAD VIEW ® A. SmartJet system lever ® B. Moto-Massage jet Comfort ® Control system lever ® C. Precision jets Comfort Control system lever D. Pillow E. Hydromassage jet with directional nozzle F. Hydromassage jet with rotary nozzle G.
® VANGUARD (MODEL V & VV) OVERHEAD VIEW ® A. SmartJet system lever ® B. Moto-Massage jet Comfort ® Control system lever ® C. Precision jets Comfort Control system lever D. Pillow E. Hydromassage jet with directional nozzle F. Hydromassage jet with rotary nozzle G.
® SOVEREIGN (MODEL I & II) OVERHEAD VIEW ® A. SmartJet system lever ® B. Moto-Massage jet Comfort ® Control system lever ® C. Precision jets Comfort ® Control system lever D. Pillow E. Hydromassage jet with directional nozzle F. Hydromassage jet with rotary nozzle G.
™ ACCOLADE (MODEL AC) OVERHEAD VIEW ® A. SmartJet system lever ® B. Precision jets Comfort Control system lever C. Pillow D. Hydromassage jet with directional nozzle E. Hydromassage jet with rotary nozzle F. Precision jets ™ G. HydroStream ® H.
® PRODIGY (MODEL H) OVERHEAD VIEW ® A. SmartJet system lever ® B. JetStream jet Comfort ® Control system lever ® C. Precision jets Comfort ® Control system lever D. Hydromassage jet with directional nozzle E. Hydromassage jet with rotary nozzle F.
® JETSETTER (MODEL J) OVERHEAD VIEW ® A. SmartJet system lever ® B. JetStream jet Comfort ® Control system lever ® C. Moto-Massage jet Comfort Control system lever ® D. Precision jets Comfort Control system lever E. Pillow F. Hydromassage jet with directional nozzle G.
It will begin blinking if the heater high-limit thermostat has tripped. If the power indicator light is blinking, follow the instructions in the Troubleshooting section to identify and correct the cause. The power indicator will stop blinking once the problem has been corrected. 230 VOLT PERMANENTLY CONNECTED MODELS ™ • Vista ® (Model SS) • Grandee ®...
Page 25
NOTE: Long wiring runs may require larger-gauge wire than stated. We recommend using a maximum 3% voltage drop when calculating wire gauge requirements. VISTA (SS) & ENVOY (KK) WIRING CONNECTIONS 1. Identify the TB-1 terminal block, located inside the control box at the lower left-hand corner.
Your Hot Spring spa has been carefully engineered to provide maximum safety against electric shock. Remember, connecting the spa to an improperly wired circuit will negate many of its safety features. Vista ® (Model SS) & Envoy ™...
NOTE: Long wiring runs may require larger-gauge wire than stated. 115-230 VOLT CONVERTIBLE MODELS • Sovereign (Model I) ® • Prodigy ® (Model H) • Jetsetter ® (Model J) 230 VOLT CONVERSION INSTRUCTIONS Refer to the following instructions to convert a 115 volt spa to a 230 volt spa. NOTE: Converting the spa to 230 volt operation should only be done by an authorized service agent or a qualified electrician.
Page 28
NOTE: The WHITE neutral wire must be attached to the load neutral on the 115 volt, 20 amp breaker (not the neutral bus bar in the subpanel). The WHITE pigtail (neutral) wire from the 20 amp breaker is already connected to the neutral bus bar. 4.
If any of the GFCI breakers fails to operate in this manner, your spa may have an electrical malfunction, and you may be risking electrical shock. Turn off all circuits and do not use the spa until the problem has been corrected by an authorized service agent. 115 VOLT OPERATION (USA ONLY) The spa must be connected to a dedicated 115 volt, 20 amp, GFCI protected, grounded circuit.
30 amp / 230 volt GFCI circuit breaker. The Grandee, Vanguard, Sovereign (II) and Accolade use the 20 amp breaker for the jet pump and control circuit while the 30 amp breaker is used for the heating system. The Vista and Envoy use the 20 amp breaker for the heating system while using the 30 amp breaker for the jet pumps and control circuit.
, and Envoy push the JETS 1 and JETS 2 buttons, push the JETS 2 button a second time on the Vista and Envoy ) to make the jet pump run on high speed for one minute. Once the jet system is fully operational (as indicated by strong, non-surging jets), priming of the spa is complete. Weak or surging jets are an indication of a low water level condition or clogged filter cartridges.
DUAL MOTO-MASSAGE NOTE: The Dual Moto-Massage jet is available on the Vista, Envoy and Vanguard (Model VV) spas only. The Dual Moto-Massage jet automatically travels two streams up and down in a sweeping motion, simulating the natural stroking effects of a ®...
ACCESSORY NOTE: Your Hot Spring Dealer stocks rotary nozzle HydroStream jet kits that can easily be installed in your Vista or Envoy spa to modify the jet from directional to dual port rotary.
Vista (Model SS) Jet System Menu ® Jet Pump 1–Jet System 1 Jet Pump 2–Jet System 1 ® Left SmartJet lever in the 3 o’clock position Right SmartJet lever in the 3 o’clock position ™ ™ • 3 Jet-Cluster system on rear wall (2 dual port rotary, •...
Grandee (Model G) Jet System Menu Grandee (Model G) Jet System Menu ® ® (Endurol) ® Jet Pump 1–Jet System 1 Jet Pump 2–Jet System 1 ® Left SmartJet lever in the 3 o’clock position Right SmartJet lever in the 3 o’clock position ®...
Page 36
Grandee (Model G) Jet System Menu Grandee (Model G) Jet System Menu ® ® Jet Pump 1–Jet System 1 Jet Pump 2–Jet System 1 ® Left SmartJet lever in the 3 o’clock position Right SmartJet lever in the 3 o’clock position ®...
Envoy (Model KK) Jet System Menu ™ Jet Pump 2–Jet System 1 Jet Pump 1–Jet System 1 Right SmartJet lever in the 3 o’clock position Left SmartJet lever in the 3 o’clock position • 7 directional Precision jets on left back wall •...
Vanguard ® Vanguard (Model V) Jet System Menu (Model V) Jet System Menu ® (Endurol) ™ Jet System 1 ® SmartJet lever in the 3 o’clock position ® • 1 Moto-Massage jet on left rear ® • 4 directional Precision jets above left Moto-Massage jet •...
Vanguard Jet System Menu ® Vanguard (Model V) Jet System Menu (Model V V) ™ Jet Pump 2-Jet System 1 Jet Pump 1-Jet System 1 ® SmartJet lever in the 3 o’clock position • 1 Moto-Massage jet on left rear ®...
Sovereign (Model I) Jet System Menu Sovereign (Model I) Jet System Menu ® ® Jet System 2 Jet System 1 ® SmartJet lever in the 6 o’clock position SmartJet lever in the 3 o’clock position ® • 1 Moto-Massage jet on left rear •...
Page 41
Sovereign (II) Jet System Menu ® Jet System 1 SmartJet lever in the 3 o’clock position • 1 Moto-Massage jet on left rear • 4 directional Precision jets above Moto-Massage jet • 10 directional Precision jets on right rear ™ •...
Accolade (Model AC) Jet System Menu ™ reign (Model I) Jet System Menu ® Jet System 1 SmartJet lever in the 3 o’clock position ™ • 2 HydroStream jets on left back wall • 1 Water Feature • 7 Precision jets on right back wall ™...
Prodigy (H) Jet System Menu ® Jet System 1 ® SmartJet lever in the 3 o’clock position ® • 10 directional Precision jets on right rear • 2 dual port rotary jets on left rear • 1 directional hydromassage jet on left wall ®...
® Envoy ™ & Vanguard (VV) ® ® ™ ® The auxiliary control panel (Vista , Grandee , Envoy , Vanguard ® ® Sovereign , Accolade and Prodigy ) is conveniently located so that a user inside the spa can operate the light or the jets.
MAIN CONTROL PANEL The main control panel provides a quick visual check of the spa’s status, and allows the user to set the temperature, activate the jets and light, and lock the temperature and/or spa functions. INDICATOR LIGHTS At a glance, the indicator lights are readily visible on the main control panel. The three indicator lights (POWER, READY and CLEAN) work independently from the rest of the control panel display.
(VV) models) which affect the jet pump(s): The JETS button (all models) / JETS 1 (Vista, Grandee, and Envoy models only) activates the jet pump. When the JETS or JETS 1 button is pressed, the jets symbol will illuminate on the control panel display. The symbol will remain lit until the button is pressed to turn off the jet pump, or after two hours of continuous operation when the pump is automatically shut off by the control system.
Summer Mode symbol will only be visible when the display is activated by pressing a control panel button. AUXILIARY CONTROL PANEL ® ® ™ ® ® ™ The auxiliary control panel, conveniently located in the spa seating area (Vista , Grandee , Envoy , Vanguard , Sovereign , Accolade , and ® Prodigy models) allows the user to activate the jets, light, and Spaudio functions from inside the spa.
The Ground Fault Circuit Interrupter is a safety device that is designed to detect as little as 5 milliamps (±1mA) of electrical current leakage to ground. Watkins Manufacturing Corporation recommends that the GFCI be tested prior to each use to ensure it is functioning correctly.
Watkins Manufacturing Corporation recommends the filter cartridges be cleaned (by soaking to dissolve minerals) at least once every month. The Tri-X filter (standard on Vista, Envoy and Accolade models only) can also be cleaned in the dishwasher using no soap and no dry cycle.
CARE OF THE SPA PILLOWS ® ® ® ® The spa pillows used on the Vista, Grandee , Envoy, Vanguard , Sovereign , Accolade and Jetsetter models will provide years of comfort if treated with care. They have been positioned above the water level to minimize the bleaching effects of chlorinated water, and other spa water chemicals.
• DO NOT place any metal or heat transferring object on the cover or place any type of plastic tarp or drop cloth over the cover as this may result in a melted foam core, which would not be covered under the warranty. • DO NOT use any lifting mechanisms, chemicals, or cleaners except those recommended by Watkins Manufacturing Corporation, or its Authorized Sales and Service Dealer.
• DO NOT lift the cover or operate the retractable cover system by using the cover locks. They are not designed to be used as handles. • DO NOT use any chemicals or cleaners except those recommended by Watkins Manufacturing Corporation, or its Authorized Sales and Service Dealer.
PREVENTION OF FREEZING ® Your Hot Spring spa has been designed and engineered for year-round use in any climate. In some areas, extremely cold temperatures (below 10°F) combined with strong wind, may cause partial freezing of the jet pump, even though the water inside the spa remains at the selected temperature.
• pH • Sanitizer Two types of testing methods are recognized and recommended by Watkins Manufacturing Corporation: The Reagent Test Kit is a method which provides a high level of accuracy. The reagents come in either liquid or tablet form.
• Always keep chemical containers closed when not in use. Replace caps on their proper containers. • Don’t inhale fumes, or allow chemicals to come in contact with your eyes, nose, or mouth. Wash your hands immediately after use. • Follow the emergency advice on the product label in case of accidental contact, or if the chemical is swallowed. Call a doctor or the local Poison Control Center.
Page 56
WARNING: DO NOT use tri-chlor chlorine, bromo-chloro-dimethyl-hydantoin (BCDMH), or any type of compressed bromine or chlorine, acid or any type of sanitizer which is not recommended by Watkins Manufacturing Corporation. Page 53...
THE WATKINS WATER MAINTENANCE QUICK REFERENCE GUIDE Ideal Range (ppm) What Chemicals to Use Steps Minimum Maximum To Raise To Lower ® 1 Total Alkalinity HotSpring FreshWater HotSpring FreshWater pH/Alkalinity Up pH/Alkalinity Down Sodium Hydrogen Sodium Bisulfate) Carbonate, or Sodium Bicarbonate) 2 Calcium Hardness HotSpring FreshWater Use a mixture of...
Prior to Add one-half (1/2) teaspoon of chlorine per Add one (1) tablespoon of monopersulfate 250 gallons (MPS)* per 250 gallons each use ® Vista Vista (Model SS) 2 tablespoons (Model SS) 1 teaspoon (Test before adding ® Grandee (Model G)
Page 59
The recommended FAC for your spa water is 3.0-5.0 ppm. ® ® B. Watkins Manufacturing Corporation recommends the use of HotSpring FreshWater Concentrated Chlorinating Granuals (sodium dichlor) for sanitizing the water. Sodium dichlor is preferred because it is totally soluble, dissolves quickly and is nearly pH neutral.
WILL cause damage to your spa. Use of a liquid or any type of compressed bromine or chlorine, acid or any type of sanitizer which is not recommended by Watkins Manufacturing Corporation WILL damage your spa and is specifically not covered under the terms of the limited warranty.
CAN NOT be used as a single-source sanitizer, water clarifier, anti-foamer, and mineral chelating agent. A secondary source sanitizer must be used to maintain 2.0 ppm (2.0 mg/L) of Free Available Chlorine (FAC). Watkins Manufacturing Corporation recommends that a chemical maintenance program based on recognized and documented industry standards still be followed when using an ozone purification system to assure water sanitation and the highest quality purified water.
WARNING: Watkins Manufacturing Corporation DOES NOT recommend the use of any floating chemical dispenser. Damage to the spa shell or components caused by a floating chemical dispenser is specifically not covered under the terms of the limited warranty.
Page 63
Unlike bromamines, chloramines are weaker, slower sanitizers. Chlorine: An efficient sanitizing chemical for spas. Watkins Manufacturing Corporation recommends the use of sodium dichlor-type granulated chlorine. This type is preferred because it is totally soluble and nearly pH neutral.
HEATER AND INTEGRATED PRESSURE SWITCH Watkins Manufacturing Corporation unconditionally warrants the No-Fault heater against any failure that would require replacement. This warranty’s duration is equal to the time period identified in the Component Warranty. This warranty defines unconditional as warranty coverage without exception provided that the component has failed to operate properly within the spa’s system.
Misuse and abuse shall include any operation of the spa other than in accordance with Watkins Manufacturing Corporation printed instructions, or use of the spa in an application for which it is not designed;...
TROUBLESHOOTING ® Should you experience any problem whatsoever, do not hesitate to contact your authorized Hot Spring dealer. Here are some tips to help you to diagnose and rectify some more common sources of trouble yourself, if you choose to do so. GENERAL OPERATION TROUBLESHOOTING GUIDE Problem Probable causes...