Master & User; Most Common Commands; Arming & Disarming; Detecting & Communicating Alarms - YOYOMOTION YOYOCam G3 User Manual

MASTER & USER
Up to 10 Users set up by the Master can access YOYOCam. Master and Users can send these
commands. Master & Users can also call YOYOCam and listen in via the built-in microphone.

Most Common Commands

Text to send
#01#
#02#
#03#
#03#Quantity#
#07#
#09# or #09#1#
#32#Size#
#33#Quantity#
#118#0# or #118#1#
#22#0# or #22#1#
#39#0#
#39#1#
#143#0# or #143#1#
NOTE: Quantity (image quantity) is in range 1-8 for image sizes 160 x 120 and 320 x 240. Quantity
must be 1-2 for image size 640 x 480.
Arming & Disarming
Text to send
#01#
#02#
#137#0# or #137#1#
#129#parameters#
#128#0# or #128#1#
#139#Times#
#138#0# or #138#1#
#176#0# or #176#1#
Detecting & Communicating Alarms
Text to send
#118#0# or #118#1#
#22#0# or #22#1#
#130#0# or #130#1#
#11#0# or #11#1#
#12#0# or #12#1#
#110#0# or #110#1#
#13#0# or #13#1#
#36#Sensitivity#
#142#0#
YOYOCam G3 User Guide v0.2
What it does
Arm YOYOCam (if an event is detected, alarm is triggered)
Disarm YOYOCam (events will be ignored)
Take one image and send it to the requesting user
Take a number (Quantity 1-8) of images and send to requestor
Check the settings and status
Get the command list (#09# for SMS, #09#1# for MMS response)
Set image size: 1: 160x128; 2: 320x240 (default); 3: 640x480
Set quantity of images to take when triggered: 1-8 (default 3; note 1)
Disable (0) infrared body detection; enable (1) (default)
Disable (0) camera based motion detection (default); enable (1)
Call mode – When Emergency button pressed, numbers are dialed
SMS/MMS mode – when Emergency button is pressed, YOYOCam
sends SMS and MMS.
Disable (0) indicator LED; enable (1) (default)
What it does
Arm YOYOCam (if an event is detected, alarm is triggered)
Disarm YOYOCam (events will be ignored)
Receive an SMS when remote control arms/disarms YOYOCam.
0: Off (default); 1: On
Set arm and disarm state by a schedule based on day and time
#129#Day#ArmTime1#DisarmTime1#ArmTime2#DisarmTime2
#ArmTime3#DisarmTime3#
Disable (0) (default) above scheduled arm/disarm state; enable (1).
Auto-disarm after Times the alarm has been triggered
Disable (0) (default) auto-disarm; enable (1).
Disable (0) or enable (1) (default) SMS notification of scheduled
arm/disarm events.
What it does
Disable (0) infrared body sensor; enable (1) (default)
Disable (0) camera motion detection; enable (1) (default)
Disable (0) (default) alarm warning bleep; enable (1)
Disable (0) alarm SMS; enable (1) (default)
Disable (0) alarm MMS; enable (1) (default)
Disable (0) alarm Email; enable (1) (default)
Disable (0) (default) alarm voice call; enable (1)
Set camera motion sensitivity from 1 (least sensitive) to 5 (most
sensitive). Default 4.
Sets number of pictures taken at motion detection to be the same
as the number taken at IR body detection.
Page 58