Activating Surround Mode; Selecting Surl-Ound Modes - JVC RX-DVSSL Instructions Manual

Creating Realis
When Auto Surround is set to "OFF" or 2-channel source other than
Dolby Surround software is played back, activate Surround mode
manually.
Make sure that you have set the speakers information correctly
(see page 20 or 53).
l
If only front speakers are connected, you cannot activate any
Surround mode.
On the front uanel:
Press SURROUND ON/OFF.
The SURROUND indicator lights up on the display
(when Auto Surround is set to "OFF").
l
Each time you press the button, Surround mode is
activated and deactivated altcrnatcly.
From the remote control:
rirlmm
' .* 1 Press CONTROL repeatedly so that
"SOUND" appears on the operation
mode display.
Number buttons now work for sound adjustments.
2 Press SURR ON/OFF.
The SURROUND indicator lights up on the
Y
a
display (when Auto Surround is set to "OFF").
l
Each time you press the button, Surround mode
is activated or deactivated alternately.
About SURROUND indicators
l
When Auto Surround is set to
"ON," the AUTO SURROUND
indicator always lights up on the
display.
l
When you activate Surround
mode manually with Auto
Surround set to "OFF," the
SURROUND indicator lights up
on the display.
Sianal and speaker indicators on the disnlay
The following signal indicators light up -:
L R
: *When digital input is selected: Light up when
the signals corresponding to each channel come
in.
l
When analog input is selected: Always light
up.
C, LS, RS : Light up when the signals corresponding to each
channel come in.
S
: Lights up when the monaural rear channel signal
or Dolby Surround encoded signal comes in.
LFE
: Lights up when the LFE channel signal comes
in.
When 2-channel source is played back with Surround mode
activated. you can select another Surround mode.
Available Surround modes will vary depending on the number of the
connected speakers and the playback sound.
Make sure that you have set the speaker information correctly
(see page 20 or 53).
* You cannot change Surround mode when playing back DVD
AUDIO multichannel track.
4 If rear speakers are not connected, you cannot use DAP modes
and All Channel Stereo.
On the front panel:
Press SURROUND MODE.
l
Each time you press the button, Surround mode
is changed as illustrated below:
v
From the remote control:
1 Press CONTROL repeatedly so that w
"SOUND" appears on the operation
mode display. v
Number buttons now work for sound adjustments.
2 Press SURR MODE.
SURRMODE
* Each time you press the button Surround mode IS
changed as illustrated below:
v
When 5 or 4 (except center speaker) speakers are connected:
When 3 (except rear speakers) speakers are connected or
Dolby Digital including matrix source is played back:
DlGIRLA"TO mPROLoGlCr
S"RIKI"NO
g!g 7.: .:.:.
:, .: : : . . . .
n n I"" j ,.,, .j!i,
: : i...
.i' **...
"OLUME
; :I :...: ....: .i. i ,...
ii..,
j :I::
/pL II MOVIE?
IL!? ll MUSIC,
L c R
q uu
LFE
piiiFq
LS s RS
017
Signal indicators Speaker Indicators
The speaker indicators light up as follows:
l
The subwoofer speaker indicator- ( JsuBwFR1) lights up when
"SUBWFR" is set to "YES" (see page 20) or "USE" (see
page 53).
* The other speaker indicator\ light up only w#hen the
corresponding speaker i\ activated. and also when required
for the current playback.
27