Powerware and X-Slot are registered trademarks and ConnectUPS is a trademark of Eaton Electrical Inc. Modbus is a registered trademark of Modicon. IBM and AS/400 are registered trademarks of International Business Machines Corp.
AC power to protect the customer’s load from all nine power failures. The Powerware 9390 UPS is available as a single module or a multiple module parallel system (see paragraph 1.1).
The UPS system configuration can be enhanced by adding optional accessories such as a Remote Emergency Power-off (REPO) control, Remote Monitor Panel II (RMP II), or X-Slot ® communication cards. EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Introduction 1.2 Using This Manual This manual describes how to install and operate the Powerware 9390 UPS (20–80 kVA) cabinet. Read and understand the procedures described in this manual to ensure trouble-free installation and operation. In particular, be thoroughly familiar with the REPO procedure (see page 10-7).
In this manual, the term UPS refers only to the UPS cabinet and its internal elements. The term UPS system refers to the entire power protection system – the UPS cabinet, the battery cabinet, and options or accessories installed. EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Keep surroundings uncluttered, clean, and free from excess moisture. Observe all DANGER, CAUTION, and WARNING notices affixed to the inside and outside of the equipment. EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Configurations) Installation and Operation Manual, the Powerware 9390 Integrated Accessory Cabinet (IAC-D Configuration) Installation and Operation Manual, the Powerware 9390 UPS Sidecar Installation and Operation Manual, or the Powerware 9390 Sync Control Installation and Operation Manual, as applicable, for the following additional information: Installation instructions, including site preparation, planning for installation, and wiring and safety information.
For the UPS system to operate at peak efficiency, the installation site should meet the environmental parameters outlined in this manual. If the UPS is to be operated at an altitude higher than 1500m (5000 ft), contact your Eaton service representative for important information about high altitude operation. The operating environment must...
UPS. LAN and telephone drops, for use with X-Slot connectivity cards, must be supplied by facility planners or the customer. EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
The cabinet is shipped bolted to a wooden pallet and protected with outer protective packaging material (see Figure 2-1). Figure 2-1. Powerware 9390 UPS (20–80 kVA) Cabinet as Shipped on Pallet C A U T I O N The UPS cabinet is heavy (see Table A on page A-3). If unpacking instructions are not closely followed, the cabinet may tip and cause serious injury.
Page 22
1. Carefully inspect the outer packaging for evidence of damage during transit. C A U T I O N Do not install a damaged cabinet. Report any damage to the carrier and contact your Eaton service representative immediately. 2. Use a forklift or pallet jack to move the packaged cabinet to the installation site, or as close as possible, before unpacking.
Additional battery cabinets are supplied without cosmetic covers. Cosmetic covers must be ordered for the UPS cabinet and/or other ancillary cabinets. EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Installing the UPS System 3.2.1 Unloading the Powerware 9390 UPS Cabinet from the Pallet The UPS cabinet is bolted to a wooden pallet supported by wood skids. To remove the pallet, perform the following procedure: W A R N I N G The UPS cabinet is heavy.
3.2.3; otherwise, proceed to paragraph 3.2.6. 3.2.2 Battery Cabinet Installation To install the battery cabinet, refer to the Powerware 9390 Integrated Battery Cabinet (Models IBC-S and IBC-L) Installation Manual. After the battery cabinet is installed, return to paragraph 3.2.6 to wire the UPS and battery cabinet.
3.2.6 to complete the UPS cabinet wiring. 3.2.4 Integrated Accessory Cabinet Installation To install and wire an IAC, refer to the Powerware 9390 Integrated Accessory Cabinet (IAC-B and IAC-T Configurations) Installation and Operation Manual or the Powerware 9390 Integrated Accessory Cabinet (IAC-D Configuration) Installation and Operation Manual.
Page 29
11. Disconnect the single-feed jumpers from phase A, B, and C terminals on rectifier input terminals and bypass input terminals. Remove the jumpers from the cabinet. EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com...
Page 30
22. Route and connect the battery cables between the UPS and battery cabinets in accordance with the instructions in the Powerware 9390 Integrated Battery Cabinet (Models IBC-S and IBC-L) Installation Manual. See Appendix A for UPS cabinet wiring access information.
8. Remove the UPS cabinet top or bottom conduit landing plate to drill or punch conduit holes (see Drawing 164201603-6 on page A-32). 9. Reinstall the conduit landing plate and install the conduit. EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
3. Remove the UPS cabinet X-Slot conduit landing plate to drill or punch conduit holes (see Drawing 164201603-6 on page A-32). 4. Reinstall the conduit landing plate and install the conduit. 3-11 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
“Installing Options and Accessories.” 3.3 Initial Startup Startup and operational checks must be performed by an authorized Eaton Customer Service Engineer, or the warranty terms specified on page W-1 become void. This service is offered as part of the sales contract for the UPS. Contact service in advance (usually a two-week notice is required) to reserve a preferred startup date.
- Accessories are mounted in installed locations and wiring is terminated inside the UPS cabinet. (OPTIONAL) - The debris shield covering the UPS cabinet ventilation grill is removed. - Startup and operational checks are performed by an authorized Eaton Customer Service Engineer. 3-13 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com...
Page 36
- Pull chain wiring between the UPMs is properly installed. - Adequate workspace exists around the UPMs, parallel tie cabinet, and other cabinets. - Startup and operational checks are performed by an authorized Eaton Customer Service Engineer. 3-14 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com...
Page 37
Installing the UPS System Notes _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ _________________________________________________________________________ 3-15 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 38
Installing the UPS System This page intentionally left blank. 3-16 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Proper disposal of batteries is required. Refer to your local codes for disposal requirements. Never dispose of batteries in a fire. Batteries may explode when exposed to flame. EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com...
C A U T I O N Do not discard waste electrical or electronic equipment (WEEE) in the trash. For proper disposal, contact your local recycling/reuse or hazardous waste center. EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
5. Remove the screws securing the control panel door and swing the door open. Retain the hardware for later use. EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 42
REPO switch rating is 24 Vdc. 1A minimum if supplied by customer. NOTE The REPO switch must be a latching-type switch with a dedicated circuit. EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com...
Page 43
16. Close the control panel door and secure with the retained hardware. 17. Reinstall the door removed in Step 4 and secure with the retained hardware. 18. Close the door and secure the latch. EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 44
Installing a Remote Emergency Power-off Switch This page intentionally left blank. EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
UPS. Remove the X-Slot cover panel to gain access to the X-Slot. See Drawing 164201603-8 starting on page A-40 for location of the X-Slot communication bay. EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
10. Install CAN wiring between UPMs. See Drawing 164201603-8 starting on page A-40 for Powerware Hot Sync CAN Bridge Card location, terminal location, and wiring information. EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
NOTE Setup of the Powerware Hot Sync CAN Bridge Card for parallel operation must be performed by an authorized Eaton Customer Service Engineer. Contact service to schedule a date. 13. When all wiring is complete, reinstall the safety shield panels removed in previous steps.
Setup of the Powerware Hot Sync CAN Bridge Card must be performed by an NOTE authorized Eaton Customer Service Engineer. Contact service to schedule a date. 9. To check the operation of the RMP II, ensure that the UPS is supplying the load via inverter or bypass.
Page 49
Setup of the Powerware Hot Sync CAN Bridge Card must be performed by an authorized Eaton Customer Service Engineer. Contact service to schedule a date. 9. Contact your Eaton service representative for verification and testing of the RIM II and its connections prior to making connections with J1 through J4 (see Table 6-1 and Drawing 164201603-12 on page A-59).
Setup of the Powerware Hot Sync CAN Bridge Card must be performed by an NOTE authorized Eaton Customer Service Engineer. Contact service to schedule a date. EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com...
Supervisory contacts are rated at 2.0A at 28 Vdc or 120 Vac and 0.15A at 115 Vdc. Supervisory contacts require an external power supply. Internal 24 Vdc is not NOTE capable of supplying contact current. EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 52
Installing Options and Accessories This page intentionally left blank. EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Understanding UPS Operation 7.1 Looking Inside the UPS System The Powerware 9390 UPS is a continuous-duty, solid-state, transformerless (at 208 and 480 Vac), three-phase, true online system that provides conditioned and uninterruptible AC power to the UPS system’s output. The UPS supports process control, data processing, telecommunications/PBX, research, and non-patient medical equipment.
7.2.1 Single Module RT Modes The Powerware 9390 UPS supports a critical load in three different modes of operation. The UPS can automatically use all three modes, as required. The standard operation...
Page 57
The following paragraphs describe the differences in the three UPS operating modes, using block diagrams to show the power flow during each mode of operation. EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com...
The UPS monitors the battery charge condition and reports the status on the control panel. The battery is always connected to the UPS and ready to support the inverter should the utility input become unavailable. EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 59
If the UPS suffers an internal failure, it switches automatically to Bypass mode and remains in that mode until the failure is corrected and the UPS is back in service. EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com...
K3 opens to isolates the inverter. The backfeed protection contactor is normally always closed, ready to support the static switch unless the bypass input source becomes unavailable. EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 61
Bypass mode is a normal operating mode, not an alarm condition. However, if the UPS is unable to return to Normal mode following an automatic transfer to Bypass mode, an alarm condition is recorded. EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
The UPS remains in this operating mode until the input power to the rectifier is again within the specified voltage or frequency acceptance windows. EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
7.3 Multiple Module Parallel System Parallel operation extends the normal operation of Powerware 9390 UPS units by offering increased capacity and/or redundant capability. The parallel system continues to maintain power to the critical loads during commercial electrical power brownout, blackout, overvoltage, undervoltage, and out-of-tolerance frequency conditions.
UPMs online than required to support the load. 7.3.1 Multiple Module Parallel System Modes Similar to the single module system, the Powerware 9390 UPS parallel system supports a critical load in three different modes of operation. The standard operation modes are: In Normal mode, the paralleled UPMs supply the critical load with clean, filtered power.
The parallel system automatically returns to Normal mode when the overload condition is cleared and system operation is restored within specified limits. 7-11 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
If more modules than can support the load must be taken offline, the load must be transferred to maintenance bypass or shut down. 7-12 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 67
In the Parallel Capacity (N + 0) arrangement, if one unit trips offline and goes to bypass, the remaining units also go to bypass. 7-13 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
The UPMs remain in this operating mode until the input power to the rectifier is again within the specified voltage or frequency acceptance windows. 7-14 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
A backfeed contactor is also provided. 7.4.5 Batteries The UPS operates from battery strings from 192 cells (384V nominal) to 240 cells (480V nominal). 7-16 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
A ConnectUPS -X Web/SNMP Card is provided as standard equipment and provides remote monitoring through a Web browser interface, e-mail, and a network management system (NMS) using SNMP. See Chapter 13, “Communication,” for additional information. EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Optional X-Slot connectivity cards are quickly installed at the front of the unit and are hot-pluggable. 8.2 Options and Accessories Contact an Eaton sales representative for information about the following options. 8.2.1 Integrated Battery Cabinets Battery backup protection can be enhanced by equipping the UPS system with up to four Powerware 9390 battery cabinets containing sealed lead-acid, maintenance-free batteries.
Features, Options, and Accessories 8.2.3 Integrated Accessory Cabinet (IAC-B, IAC-T, and IAC-D) The following IACs are designed for use with the Powerware 9390 three-phase Uninterruptible Power Systems: The IAC-B provides maintenance bypass functions. The IAC-T provides parallel tie cabinet or parallel tie cabinet with maintenance bypass functions.
This symbol indicates that you should not discard waste electrical or electronic equipment (WEEE) in the trash. For proper disposal, contact your local recycling/reuse or hazardous waste center. EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Chapter 10, “UPS Operating Instructions,” for use of the operational controls. When the unit powers up, the screen displays the Eaton | Powerware logo as shown in Figure 9-1. To advance to the Main Menu and Mimic screen, press any control panel pushbutton once.
Set UPS parameters (see paragraphs 9.2.8 and 9.2.9) Control UPS operation (see paragraph 9.3) After approximately 30 minutes, the display screen darkens. To restore the screen, press any pushbutton once. EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
BYPASS AC UNDER VOLTAGE NOTICE: BATTERY VOLTAGE LOW NOTICE: NO SYNC ON NOTICE: BYPASS NOT AVAILABLE NOTICE: CONFIGURATION ERROR HISTORY Figure 9-4. Active Events Screen EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
The Unit Meter screens show the UPS meter readings for the unit (or units, if a parallel system is installed). The default voltage displayed on these screens is phase-to-neutral. However, an authorized Eaton Customer Service Engineer can change the screens to display the voltage phase-to-phase (A-B, B-C, C-A).
BYPASS --- UNIT FREQ LEAD SYSTEM UNIT Figure 9-8. Unit Bypass Meter Screen EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
The Battery screen displays the battery voltage (Vdc), the battery current (Idc), the minutes of battery time remaining, and battery temperature. Battery temperature must be set up by an authorized Eaton Customer Service Engineer. When battery life decreases to less than 20%, Check Battery is displayed.
07/28/2005 AVERAGE TIME ON BATTERY ** M ** S TOTAL TIME ON BATTERY ** H ** M Figure 9-11. Battery Discharge Log Summary Screen EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
** M ** S LOAD WHEN ON BATTERY ***.** KW END VOLTAGE : ***.** V RESET SUMMARY Figure 9-12. Battery Discharge Log Screen 9-10 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
TOTAL TIME OVER LIMIT ** MINUTES TOTAL KWH USED OVER LIMIT *** . ** KWH SETUP Figure 9-13. KW Demand Log Summary Screen 9-11 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
TIME OVER LIMIT 2 MINUTES KWH USED OVER LIMIT *** . ** NUM TIMES OVER THIS INTERVAL RESET SUMMARY Figure 9-14. KW Demand Log Screen 9-12 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
The Time Interval Monitored Setup Save screen is displayed. TIME INTERVAL MONITORED SETUP 0000 DONE Figure 9-17. Time Interval Monitored Setup Screen 9-15 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Current KW Demand Log Setup screen 2 displays. If RETRY is pressed, the Time Interval Monitored Setup screen is redisplayed. TIME INTERVAL MONITORED SETUP 0000 SAVE RETRY ABORT Figure 9-18. Time Interval Monitored Setup Save Screen 9-16 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
The Maximum Level (KW) Setup Save screen is displayed. MAXIMUM LEVEL (KW) SETUP 0000 DONE Figure 9-19. Maximum Level (KW) Setup Screen 9-17 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Current KW Demand Log Setup screen 2 displays. If RETRY is pressed, the Maximum Level (KW) Setup screen is redisplayed. MAXIMUM LEVEL (KW) SETUP 0000 SAVE RETRY ABORT Figure 9-20. Maximum Level (KW) Setup Save Screen 9-18 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
MAXIMUM % OF FULL LOAD *** . ** % TOTAL TIME OVER LIMIT ** MINUTES SETUP Figure 9-21. Maximum Current Log Summary Screen 9-19 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
*** . ** % TIME OVER LIMIT 2 MINUTES NUM TIMES OVER THIS INTERVAL RESET SUMMARY Figure 9-22. Maximum Current Log Screen (Three-Phase Measurement) 9-20 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
3 MINUTES MAXIMUM % OF FULL LOAD *** % LEVEL BASED ON 3 PHASE AVERAGE CHANGE Figure 9-24. Maximum Current Log Setup Screen 1 9-21 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
MAXIMUM CURRENT LOG SETUP TIME INTERVAL MONITORED MAXIMUM % OF FULL LOAD CALCULATION METHOD SELECT Figure 9-25. Maximum Current Log Setup Screen 2 9-22 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
The Time Interval Monitored Setup Save screen is displayed. TIME INTERVAL MONITORED SETUP 0000 DONE Figure 9-26. Time Interval Monitored Setup Screen 9-23 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Maximum Current Log Setup screen 2 displays. If RETRY is pressed, the Time Interval Monitored Setup screen is redisplayed. TIME INTERVAL MONITORED SETUP 0000 SAVE RETRY ABORT Figure 9-27. Time Interval Monitored Setup Save Screen 9-24 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
The Maximum % of Full Load Setup Save screen is displayed. MAXIMUM % OF FULL LOAD SETUP DONE Figure 9-28. Maximum % of Full Load Setup Screen 9-25 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Full Load Setup screen is redisplayed. MAXIMUM % OF FULL LOAD SETUP SAVE RETRY ABORT Figure 9-29. Maximum % of Full Load Setup Save Screen 9-26 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
MAXIMUM CURRENT LOG SETUP LEVEL BASED ON 3 PHASE AVERAGE LEVEL BASED ON INDIVIDUAL PHASES SELECT Figure 9-30. Calculation Method Setup Screen 9-27 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
The System Meters screens show the total system and individual UPS unit meter readings from any unit, when a parallel system is installed. The default voltage displayed on these screens is phase-to-neutral. However, an authorized Eaton Customer Service Engineer can change the screens to display the voltage phase-to-phase (A-B, B-C, C-A).
PF is calculated from the total values for the kVA and kW. OUTPUT TOTAL SYSTEM FREQ LEAD SYSTEM UNIT Figure 9-32. Total System Output Meter Screen 9-29 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
UPS, as well as the kVA, kW, and power factor measurements for the selected unit. OUTPUT UNIT X FREQ LEAD SYSTEM UNIT Figure 9-33. Output Unit X Meter Screen 9-30 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
BYPASS UNIT X FREQ LEAD SYSTEM UNIT Figure 9-35. Bypass Unit X Meter Screen 9-31 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
The Battery screen displays the battery voltage (Vdc), the battery current (Idc), the minutes of battery time remaining, and battery temperature. Battery temperature must be set up by an authorized Eaton Customer Service Engineer When battery life decreases to less than 20%, Check Battery is displayed.
SELECT pushbutton to display the function screen. SYSTEM SETUP LEVEL 0 ENTER PASSWORD CONTRAST ADJUST VERSIONS UNIT TYPE SELECT Figure 9-38. System Setup Level 0 Screen 9-33 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Setup screen displays. To return to the System Setup screen without saving the setting, press the pushbutton. CONTRAST ADJUST SAVE Figure 9-39. Contrast Adjust Screen 9-34 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
The Unit Type screen provides the model, CTO, and serial numbers of the UPS unit. Figure 9-41 shows the Unit Type screen. To return to the System Setup screen, press the pushbutton. UNIT TYPE MODEL: POWERWARE 9390 CTO: 0000000000000000 SERIAL: 0000000000000000 Figure 9-41.
DONE pushbutton. The System Setup Level 1 menu screen is displayed. The default password is L1. ENTER PASSWORD DONE Figure 9-42. Enter Password Screen 9-36 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
SYSTEM SETUP LEVEL 1 LOG OUT ENTER PASSWORD CHANGE PASSWORD ENTER PASS- CONTRAST ADJUST WORD VERSIONS UNIT TYPE SELECT Figure 9-43. System Setup Level 1 Screen 9-37 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Once the new password is entered, press the DONE pushbutton. The Change Password Save screen is displayed. CHANGE PASSWORD OLD: NEW: DONE Figure 9-44. Change Password Screen 9-38 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
System Setup screen displays. If RETRY is pressed, the Change Password screen is redisplayed. CHANGE PASSWORD OLD: NEW: ABORT SAVE RETRY Figure 9-45. Change Password Save Screen 9-39 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Set Date and Time screen. To return to the System Setup screen, press the pushbutton. TIME FORMAT SETUP MM/DD/YYYY DD/MM/YYYY SELECT Figure 9-46. Time Format Screen 9-40 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
System Setup screen, select the pushbutton. SET DATE AND TIME MM/DD/YYYY MONTH DATE YEAR HOUR MINUTE SAVE 2004 Figure 9-47. Set Date and Time MM/DD/YYYY Screen 9-41 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
System Setup screen, select the pushbutton. SET DATE AND TIME DD/MM/YYYY DATE MONTH YEAR HOUR MINUTE SAVE 2004 Figure 9-48. Set Date and Time DD/MM/YYYY Screen 9-42 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
SELECT pushbutton. To return to the System Setup screen, press the pushbutton. COM PORT SETUP COM 1 COM 2 COM 3 SELECT Figure 9-49. COM Port Setup Screen 9-43 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Once the action is completed, the COM Port Setup screen appears. COM 1 SETUP BAUD RATE 19200 DATA BITS STOP BITS PARITY NONE ABORT SAVE Figure 9-50. COM Setup Screen 9-44 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
System Controls screens. SYSTEM CONTROLS MAINTENANCE BYPASS BYPASS ONLINE POWER MODULE (PM) CHARGER LOAD OFF NORMAL BYPASS Figure 9-51. System Controls Screen 1 9-45 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
On and Off. For detailed information about using the System Controls, see Chapter 10, “UPS Operating Instructions.” 9-46 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Chapter 10, “UPS Operating Instructions.” HOLD LOAD OFF BUTTON FOR 3 SECONDS TO TURN OFF LOAD CANCEL LOAD OFF Figure 9-53. Load Off Screen 9-47 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
The indicator flashes until acknowledged by pressing any control panel pushbutton once. For more information about audible horns, see “System Event Horns” on page 12-1. 9-48 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Normal mode. The status indicator on the UPS control panel indicates the UPS is in Bypass mode. If Auto Bypass is not enabled, the UPS output remains off until the UPS transfers to Normal mode. 10-1 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
The critical load is immediately supplied by the bypass source, in Bypass mode. 7. The UPS is now operating in Bypass mode and the BYPASS status indicator is illuminated. 10-2 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
The UPS transfers to Bypass mode and the critical load is immediately supplied by the bypass source. If the bypass source is not available, the power processor remains on and an alarm sounds. 10-3 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
The bypass source supplies the critical load. W A R N I N G Power is present inside the UPS cabinets. 10-4 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
System Controls Screen 2. 3. Press the CHGR ON or CHGR OFF pushbutton on the System Controls menu bar to toggle the charger on or off. 10-5 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
W A R N I N G Power is present inside the UPS cabinet until the upstream input feeder circuit breaker is opened. 10-6 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
W A R N I N G Power is present inside the UPS cabinet until the upstream input feeder circuit breaker is opened. 10-7 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Normal mode. 9. The UPMs are now operating in Normal mode and the NORMAL status indicator on each UPM is illuminated. 10-8 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
The critical load is immediately supplied by the bypass source, in Bypass mode. 7. The UPMs are now operating in Bypass mode and the BYPASS status indicator on each UPM is illuminated. 10-9 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
3. The UPMs are now operating in Normal mode, and the NORMAL status indicator on each UPM is illuminated. The power module (PM) status indicates ONLINE on each UPM. 10-10 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
5. Press the CONTROLS pushbutton on the main menu bar of the UPM. The System Controls screen appears. 6. On the System Controls screen, the power module (PM) status should indicate SHUTDOWN. 10-11 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
The bypass source supplies the critical load. 6. Repeat Steps 2, 4, and 5 for each UPM, except the last UPM. 10-12 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
When LOAD OFF is selected and held for three seconds, the input, output, and bypass backfeed contactors open, the battery breaker or disconnect is tripped, and the power module is turned off. 10-13 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
2. To restart the UPMs after using the REPO pushbutton, reset the REPO switch and then follow the procedure in paragraph 10.2.1 or 10.2.2. 10-14 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
UPS horn may not be heard immediately. C A U T I O N Contacts should not be operated in excess of 120 Vac @ 5A maximum. 11-1 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Figure 11-1 shows an RMP II. Figure 11-1. Remote Monitor Panel II 11-2 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 139
The UPS is preparing to shut down because the UPS is in Battery mode and the DC voltage is approaching its low limit. This indicator is accompanied by a horn. 11-3 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
TB2-10 through TB2-12 ON BATTERY TB2-13 through TB2-15 UPS ALARM TB2-16 through TB2-18 ON BYPASS TB2-19 through TB2-21 SHUTDOWN IMMINENT TB2-22 through TB2-24 11-5 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 142
Using Features and Options This page intentionally left blank. 11-6 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
The messages are divided into four categories: alarms, notices, status, and commands. The following tables contain the events displayed on the Events screen of the control panel. 12-1 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 144
*Log codes indicate where the UPS records the event: H = History log; HA = History and Active logs; and A = Active log only. 12-2 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 145
*Log codes indicate where the UPS records the event: H = History log; HA = History and Active logs; and A = Active log only. 12-3 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 146
*Log codes indicate where the UPS records the event: H = History log; HA = History and Active logs; and A = Active log only. 12-4 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 147
*Log codes indicate where the UPS records the event: H = History log; HA = History and Active logs; and A = Active log only. 12-5 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 148
*Log codes indicate where the UPS records the event: H = History log; HA = History and Active logs; and A = Active log only. 12-6 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 149
*Log codes indicate where the UPS records the event: H = History log; HA = History and Active logs; and A = Active log only. 12-7 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 150
*Log codes indicate where the UPS records the event: H = History log; HA = History and Active logs; and A = Active log only. 12-8 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 151
*Log codes indicate where the UPS records the event: H = History log; HA = History and Active logs; and A = Active log only. 12-9 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 152
Responding to System Events This page intentionally left blank. 12-10 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Chapter 13 Communication This chapter describes the communication features of the Powerware 9390 20–80 kVA UPS and provides information about connecting hardware and using Terminal mode. 13.1 X-Slot Cards The Powerware 9390 UPS has a standard, factory-installed X-Slot communication bay with two slots.
Industrial Relay Card Figure 13-1. Optional X-Slot Cards 13.2 LanSafe Power Management Software Each Powerware 9390 UPS ships with LanSafe Power Management Software. To begin installing LanSafe software, see the instructions accompanying the Powerware Software Suite CD. LanSafe software uses an RS-232 serial link to communicate with the UPS. The software provides up-to-date graphics of UPS power and system data and power flow, a complete record of critical power events, and notification of important UPS or power information.
See Chapter 9, “Using the Control Panel,” for instructions on navigating the control panel. 13-3 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
If a port is operating in Terminal mode and is connected to a computer, you can press [Esc] [H] to print the entire log with a firmware version header. 13-4 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
03/12/2004 14:17:25.557 ALARM: Battery Under Voltage OK 03/12/2004 14:19:01.899 CMD: PPU On Command 03/12/2004 14:19:04.089 STATUS: K1 (Input) Closed Figure 13-2. Sample Event History Log 13-5 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 158
Communication This page intentionally left blank. 13-6 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Eaton service representative. If the string requires service, refer to the battery manufacturer’s operating manual for instructions on battery maintenance or contact your Eaton service representative. Observe these precautions when working on or around batteries: Remove watches, rings, or other metal objects.
2. Ensure the air intakes (vents on the front doors) and exhaust opening (on top of the UPS cabinet sections) are not blocked. 14-2 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
3. Record the check results and any corrective actions in a suitable log. 14.2.3 ANNUAL Maintenance Annual preventive maintenance should be performed only by authorized service personnel familiar with maintenance and servicing of the UPS system. Contact your Eaton service representative for more information about service offerings. 14.2.4 BATTERY Maintenance Contact your Eaton service representative for battery maintenance.
Page 162
Maintaining the UPS System This page intentionally left blank. 14-4 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
The UPS systems are housed in free-standing cabinets with safety shields behind the doors. The UPS systems are available in 50/60 Hz with various output power ratings. SModels Power Rating Frequency Powerware 9390-40/20 20 kVA 50/60 Hz Powerware 9390-40/30 30 kVA...
Meets IEC 801-2 specifications. Withstands up to 25 kV pulse without damage and with no disturbance or adverse effect to (ESD) Immunity the critical load. 15-2 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
220 Vac for operation from 187 Vac to 242 Vac 480 Vac for operation from 408 Vac to 528 Vac Operating Output Current See Appendix A, Table S through Table V. 15-3 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 166
Product Specifications This page intentionally left blank. 15-4 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 167
Installation Information The information in this appendix is helpful during the planning and installation of the UPS system. This appendix contains the following drawings: 164201603-1 Typical Powerware 9390 UPS System 164201603-2 Physical Features and Requirements 164201603-3 UPS System Oneline Configurations...
Installation Information BATTERY CABINET UPS CABINET DESCRIPTION: TYPICAL POWERWARE 9390 UPS SYSTEM DRAWING NO: SHEET: 164201603---1 1 of 1 REVISION: DATE: 091505 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 169
Table A. UPS Cabinet Weight Weight Voltage kg (lb) Model Input Output Shipping Installed Point Loading 208V/220V 208V/220V Powerware 9390---40/20 231 (508) 208 (458) 4 at 52.2 (115) 480V 480V 208V/220V 208V/220V Powerware 9390---40/30 231 (508) 208 (458) 4 at 52.2 (115)
Page 170
Ventilation required for cooling air exhaust: approximately 472 liter/sec (1000 cfm). DESCRIPTION: PHYSICAL FEATURES AND REQUIREMENTS DRAWING NO: SHEET: 164201603---2 2 of 2 REVISION: DATE: 110106 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 171
Single-Feed or Dual-Feed 9390---80/50 3+1 and 4+0 Configurations 9390---80/60 9390---80/80 DESCRIPTION: UPS SYSTEM ONELINE CONFIGURATIONS DRAWING NO: SHEET: 164201603---3 1 of 1 REVISION: DATE: 110106 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 172
OUTPUT CONTACTOR BREAKER (K3) FUSE INVERTER UPS CABINET POWERWARE 9390 20–80 KVA UPS SYSTEM 208V/220V INPUT AND 208V/220V OUTPUT 480V INPUT AND 480V OUTPUT SINGLE-FEED OR DUAL-FEED NOTE: 1. See Paragraph 3.2.6 on page 3 ---6 DESCRIPTION: UPS SYSTEM ONELINE DRAWING for dual-feed.
Page 173
DO NOT use one feed or a single-feeder breaker to supply both the UPS and the maintenance bypass. DESCRIPTION: UPS SYSTEM ONELINE DRAWING DRAWING NO: SHEET: 164201603---4 2 of 5 REVISION: DATE: 091505 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 174
UPS SYSTEM ONELINE DRAWING DRAWING NO: SHEET: 3 of 5 164201603---4 3. See Note 28 on page A ---25 for neutral bonding instructions. REVISION: DATE: 091505 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 175
UPS SYSTEM ONELINE DRAWING DRAWING NO: SHEET: 4 of 5 3. See Note 28 on page A ---25 for 164201603---4 neutral bonding instructions. REVISION: DATE: 091505 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 176
UPS SYSTEM ONELINE DRAWING DRAWING NO: SHEET: 5 of 5 3. See Note 28 on page A ---25 for 164201603---4 neutral bonding instructions. REVISION: DATE: 091505 A-10 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 177
Installation Information Table E. INPUT/OUTPUT Ratings & External Wiring Requirements for the Powerware 9390---40/20 Units Rating 50/60 Hz Basic Unit Rating at 0.9 lagging pF load Input and Bypass Input VOLTS 208/220 Output VOLTS 208/220 AC Input to UPS Rectifier (0.98 min. pF)
Page 178
Installation Information Table F. INPUT/OUTPUT Ratings & External Wiring Requirements for the Powerware 9390---40/30 Units Rating 50/60 Hz Basic Unit Rating at 0.9 lagging pF load Input and Bypass Input VOLTS 208/220 Output VOLTS 208/220 AC Input to UPS Rectifier (0.98 min. pF)
Page 179
3 of 5, 4 of 5, and 5 of 5. C A U T I O N DELTA SOURCES (TN-S) - The Powerware 9390 UPS system can be operated only from a delta supply source that is fully floating and if the neutral-forming transformer kit (PN 103005400) is installed in the UPS.
Page 180
Installation Information Table H. INPUT/OUTPUT Ratings & External Wiring Requirements for the Powerware 9390---80/50 Units Rating 50/60 Hz Basic Unit Rating at 0.9 lagging pF load Input and Bypass Input VOLTS 208/220 Output VOLTS 208/220 AC Input to UPS Rectifier (0.98 min. pF)
Page 181
Installation Information Table I. INPUT/OUTPUT Ratings & External Wiring Requirements for the Powerware 9390---80/60 Units Rating 50/60 Hz Basic Unit Rating at 0.9 lagging pF load Input and Bypass Input VOLTS 208/220 Output VOLTS 208/220 AC Input to UPS Rectifier (0.98 min. pF)
Page 182
Installation Information Table J. INPUT/OUTPUT Ratings & External Wiring Requirements for the Powerware 9390---80/80 Units Rating 50/60 Hz Basic Unit Rating at 0.9 lagging pF load Input and Bypass Input VOLTS 208/220 Output VOLTS 208/220 AC Input to UPS Rectifier (0.98 min. pF)
Page 183
Table N for conduit requirements. Drawing 164201603 ---7 shows the location of the power cable terminals inside the UPS cabinet. Table K. UPS Cabinet Power Cable Terminations for the Powerware 9390---80/40, 9390---80/50, 9390---80/60, and 9390---80/80 (208V/220V Input and 208V/220V Output)
Page 184
Installation Information Table L. UPS Cabinet Power Cable Terminations for the Powerware 9390---40/20, 9390---40/30, and 9390---40/40 (208V/220V Input and 208V/220V Output and 480V Input and 480V Output) Tightening Size of Pressure Type Terminal Function Terminal Function Torque Termination Screw Nm (lb in)
Page 185
Installation Information Table M. UPS Cabinet Power Cable Terminations for the Powerware 9390---80/40, 9390---80/50, 9390---80/60, and 9390---80/80 (480V Input and 480V Output) Tightening Size of Pressure Type Terminal Function Terminal Function Torque Termination Screw Nm (lb in) AC Input to UPS Rectifier...
Page 186
Table N. All Powerware 9390 products can accommodate a double size neutral. Conduit sizes were chosen from NEC Table C1, type letters RHH, RHW, RHW-2, TW, THW, THHW, THW-2.
Page 189
Table P. Table O. Maximum Input Circuit Breaker Ratings Input Voltage Rating UPS Model 208V/220V 480V 80% Rated Powerware 9390---40/20 100% Rated 80% Rated 125A Powerware 9390---40/30 100% Rated 100A 80% Rated...
Page 190
Table P lists the maximum rating for bypass and output circuit breakers satisfying the criteria for both. Table P. Maximum Bypass and Output Circuit Breaker Ratings Output Voltage Rating UPS Model 208V/220V 480V 80% Rated Powerware 9390---40/20 100% Rated 80% Rated 125A Powerware 9390---40/30 100% Rated 100A 80% Rated...
Page 191
UPS. C A U T I O N DELTA SOURCES (TN-S) - The Powerware 9390 UPS system can be operated only from a delta supply source that is fully floating and if the neutral-forming transformer kit (PN 103005400) is installed in the UPS.
Page 192
Setup of the CAN Bridge card for parallel operation must be performed by an authorized Eaton Customer Service Engineer . Contact service to schedule a date. For parallel system circuit breaker ratings, see appropriate information in Table R.
Page 193
Installation Information Table S. INPUT/OUTPUT Ratings for Powerware 9390---40/20, 9390---40/30, 9390---40/40 and 9390---80/40 Parallel Systems Configuration Units Rating 50/60 Hz Basic Unit Rating at 0.9 lagging pF load Input and Bypass Input VOLTS 208/220 Output VOLTS 208/220 AC Input from UPM...
Page 194
Installation Information Table T. INPUT/OUTPUT Ratings for Powerware 9390---80/50 Parallel System Configuration Units Rating 50/60 Hz Basic Unit Rating at 0.9 lagging pF load Input and Bypass Input VOLTS 208/220 Output VOLTS 208/220 AC Input from UPM Amps 139/131 Full Load Current for each Module...
Page 195
Installation Information Table U. INPUT/OUTPUT Ratings for Powerware 9390---80/60 Parallel System Configuration Units Rating 50/60 Hz Basic Unit Rating at 0.9 lagging pF load Input and Bypass Input VOLTS 208/220 Output VOLTS 208/220 AC Input from UPM Amps 167/158 Full Load Current for each Module...
Page 196
Installation Information Table V. INPUT/OUTPUT Ratings for Powerware 9390---80/80 Parallel System Configuration Units Rating 50/60 Hz Basic Unit Rating at 0.9 lagging pF load Input and Bypass Input VOLTS 208/220 Output VOLTS 208/220 AC Input from UPM Amps 222/210 Full Load Current for each Module...
Page 197
UPM 3 Outputs from UPMs Battery UPM 4 Battery DESCRIPTION: POWER WIRING INSTALLATION NOTES DRAWING NO: SHEET: 164201603---5 21 of 21 REVISION: DATE: 110106 A-31 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 198
(REMOVE PANELS TO DRILL OR PUNCH CONDUIT HOLES.) TOP VIEW DESCRIPTION: CONDUIT AND WIRE ENTRY LOCATIONS DRAWING NO: SHEET: 164201603---6 1 of 2 REVISION: DATE: 091505 A-32 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 199
AS REQUIRED, TO ROUTE WIRES BETWEEN CABINETS. DESCRIPTION: CONDUIT AND WIRE ENTRY LOCATIONS DRAWING NO: SHEET: 164201603---6 2 of 2 REVISION: DATE: 091505 A-33 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 200
UPS POWER TERMINAL LOCATIONS opened to gain access to DRAWING NO: SHEET: 164201603---7 1 of 6 terminals. REVISION: DATE: 032406 A-34 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 201
MODELS 80/40, 80/50, 80/60, AND 80/80 208V/220V INPUT AND 208V/220V OUTPUT DESCRIPTION: UPS POWER TERMINAL LOCATIONS DRAWING NO: SHEET: 164201603---7 2 of 6 REVISION: DATE: 091505 A-35 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 202
UPS POWER TERMINAL LOCATIONS terminals must be removed or DRAWING NO: SHEET: 164201603---7 3 of 6 opened to gain access to terminals. REVISION: DATE: 032406 A-36 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 203
208V/220V INPUT AND 208V/220V OUTPUT 480V INPUT AND 480V OUTPUT DESCRIPTION: UPS POWER TERMINAL LOCATIONS DRAWING NO: SHEET: 164201603---7 4 of 6 REVISION: DATE: 091505 A-37 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 204
UPS POWER TERMINAL LOCATIONS terminals must be removed or DRAWING NO: SHEET: 164201603---7 5 of 6 opened to gain access to terminals. REVISION: DATE: 032406 A-38 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 205
MODELS 80/40, 80/50, 80/60, AND 80/80 480V INPUT AND 480V OUTPUT DESCRIPTION: UPS POWER TERMINAL LOCATIONS DRAWING NO: SHEET: 164201603---7 6 of 6 REVISION: DATE: 091505 A-39 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 206
TO COMMON SIDE OF ISOLATED RELAY CONTACT. DESCRIPTION: INTERFACE WIRING INSTALLATION NOTES AND TERMINAL LOCATIONS DRAWING NO: SHEET: 164201603---8 1 of 13 REVISION: DATE: 032406 A-40 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 207
NOTES AND TERMINAL LOCATIONS opened to gain access to DRAWING NO: SHEET: 2 of 13 terminals. 164201603---8 REVISION: DATE: 032406 A-41 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 208
EPO contact is not used. DESCRIPTION: INTERFACE WIRING INSTALLATION NOTES AND TERMINAL LOCATIONS DRAWING NO: SHEET: 3 of 13 164201603---8 REVISION: DATE: 032406 A-42 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 209
2. The building alarms can be programmed to display the alarm functional name. DESCRIPTION: INTERFACE WIRING INSTALLATION NOTES AND TERMINAL LOCATIONS DRAWING NO: SHEET: 4 of 13 164201603---8 REVISION: DATE: 091505 A-43 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 210
UPS is in Normal mode. DESCRIPTION: INTERFACE WIRING INSTALLATION NOTES AND TERMINAL LOCATIONS DRAWING NO: SHEET: 5 of 13 164201603---8 REVISION: DATE: 032406 A-44 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 211
The REPO switch must be a latching-type switch with a dedicated circuit. DESCRIPTION: INTERFACE WIRING INSTALLATION NOTES AND TERMINAL LOCATIONS DRAWING NO: SHEET: 6 of 13 164201603---8 REVISION: DATE: 032406 A-45 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 212
Minimum Wire Size: 22 AWG for auxiliary contact ratings. DESCRIPTION: INTERFACE WIRING INSTALLATION NOTES AND TERMINAL LOCATIONS DRAWING NO: SHEET: 7 of 13 164201603---8 REVISION: DATE: 032406 A-46 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 213
24 Vdc at 6A Maximum DESCRIPTION: INTERFACE WIRING INSTALLATION NOTES AND TERMINAL LOCATIONS DRAWING NO: SHEET: 8 of 13 164201603---8 REVISION: DATE: 091505 A-47 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 214
NOTES AND TERMINAL LOCATIONS NOTE: All interface wiring is to be provided DRAWING NO: SHEET: 9 of 13 164201603---8 by the customer. REVISION: DATE: 091505 A-48 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 215
(IF INSTALLED) PARALLEL SYSTEM CAN WIRING DESCRIPTION: INTERFACE WIRING INSTALLATION NOTES AND TERMINAL LOCATIONS DRAWING NO: SHEET: 10 of 13 164201603---8 REVISION: DATE: 091505 A-49 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 216
PARALLEL SYSTEM BACKUP DESCRIPTION: INTERFACE WIRING INSTALLATION CONTROL (PULL CHAIN) NOTES AND TERMINAL LOCATIONS WIRING DRAWING NO: SHEET: 11 of 13 164201603---8 REVISION: DATE: 032406 A-50 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
FRONT VIEW RIGHT SIDE VIEW DESCRIPTION: UPS CABINET DIMENSIONS DRAWING NO: SHEET: 164201603---9 1 of 4 REVISION: DATE: Dimensions are in millimeters [inches] 091505 A-53 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 220
LEFT SIDE FRONT BOTTOM VIEW DESCRIPTION: UPS CABINET DIMENSIONS DRAWING NO: SHEET: 2 of 4 164201603---9 REVISION: DATE: Dimensions are in millimeters [inches] 091505 A-54 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 221
BOTTOM VIEW with OPTIONAL FLOOR MOUNTING BRACKETS DESCRIPTION: UPS CABINET DIMENSIONS DRAWING NO: SHEET: 3 of 4 164201603---9 REVISION: DATE: 091505 Dimensions are in millimeters [inches] A-55 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 222
BOTTOM VIEW with OPTIONAL SEISMIC MOUNTING BRACKETS DESCRIPTION: UPS CABINET DIMENSIONS DRAWING NO: SHEET: 4 of 4 164201603---9 REVISION: DATE: Dimensions are in millimeters [inches] 091505 A-56 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 223
Minimum wire size #22 AWG. DESCRIPTION: OPTIONAL REMOTE EMERGENCY POWER-OFF DRAWING NO: SHEET: 164201603---10 1 of 1 REVISION: DATE: Dimensions are in millimeters [inches] 091505 A-57 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 224
HOLES FACING UP) DESCRIPTION: OPTIONAL REMOTE MONITOR PANEL DRAWING NO: SHEET: 164201603---11 1 of 1 REVISION: DATE: 091505 Dimensions are in millimeters [inches] A-58 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 225
HOLES FACING UP) DESCRIPTION: OPTIONAL RELAY INTERFACE MODULE DRAWING NO: SHEET: 164201603---12 1 of 2 REVISION: DATE: Dimensions are in millimeters [inches] 091505 A-59 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 226
Installation Information 15–PIN D–SUB CONNECTORS DESCRIPTION: OPTIONAL RELAY INTERFACE MODULE DRAWING NO: SHEET: 164201603---12 2 of 2 REVISION: DATE: 091505 A-60 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 227
HOLES FACING UP) DESCRIPTION: OPTIONAL SUPERVISORY CONTACT MODULE DRAWING NO: SHEET: 164201603---13 1 of 1 Dimensions are in millimeters [inches] REVISION: DATE: 091505 A-61 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 228
Installation Information This page intentionally left blank. A-62 EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...
Page 229
OTHER LIMITATIONS: Eaton’s obligations under this Warranty are expressly conditioned upon receipt by Eaton of all payments due to it (including interest charges, if any). During such time as Eaton has not received payment of any amount due to it for the Product, in accordance with the contract terms under which the Product is sold, Eaton shall have no obligation under this Warranty.
Page 230
Warranty This page intentionally left blank. EATON Powerware 9390 UPS (20–80 kVA) Installation and Operation Manual S 164201603 Rev 1 www.powerware.com ®...