Regulatory Information; Accessories And Replacement Parts - Mitsubishi Electric MIFH1 Installation Manual

Regulatory information

FCC Compliance Statement (Part 15.19) (USA only)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1 This device may not cause harmful interference, and
2 This device must accept any interference received, including interference that may cause undesired operation.
FCC Warning (Part 15.21) (USA only)
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
FCC Interference Statement (Part 15.105 (b)) (USA only)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Wireless receiver, remote controller and outdoor sensor
To comply with FCC and Industry Canada RF exposure limits for general population/ uncontrolled exposure, the antenna(s) used
for these transmitters must be installed to provide a separation distance of at least 20 cm from all persons and must not be
co-located or operating in conjunction with any other antenna or transmitter.
Portable Central Controller
This portable transmitter with its antenna complies with FCC and Industry Canada RF exposure limits for general population/
uncontrolled exposure. This device must not be co-located or operating in conjunction with any other antenna or transmitter.
Section 7.1.5 of RSS-GEN
Operation is subject to the following two conditions:
1 this device may not cause interference, and
2 this device must accept any interference, including interference that may cause undesired operation of the device.
Specifications & replacement parts
Operating Ambient Temperature
Remote Controller: 32 to 120° F (0 to 48.9° C)
Portable Central Controller: 32 to 120° F (0 to
48.9° C)
Wireless receiver: -40 to 165° F (-40 to 73.9° C)
Outdoor air sensor: -40 to 140° F (-40 to 60° C)
Operating Relative Humidity
Remote Controller: 5% to 90% (non-
condensing)
Portable Central Controller: 5% to 90% (non-
condensing)
Wireless receiver: 5% to 95% (non-condensing)
Outdoor air sensor: 0% to 100% (condensing)
Physical Dimensions (height, width, depth)
Remote Controller: 3-9/16 x 5-13/16 x 1-1/2
inches (91 x 147 x 38 mm)
Wireless receiver: 6-7/16 x 3-1/4 x 1-5/16
inches (164 x 82.5 x 34 mm)
Outdoor air sensor: 5 x 3-1/2 x 1-11/16 inches
(127 x 89 x 43 mm)
Portable Central Controller: 6-1/4 x 3-1/8 x
1-5/8 inches (158.2 x 79.9 x 42 mm)
© 2010 Mitsubishi Electric & Electronics USA, Inc.
Suwanee, GA 30024 All Rights Reserved.
The three diamond logo is a registered trademark
of Mitsubishi Electric Corporation
69-2426—01 M.S. 11-10
Printed in U.S.A.
Accessories & Replacement Parts
Item
Portable Central Controller
Outdoor air sensor
Remote Controller
Receiver and Cable
Cable
Part Number
MCCH1
MOS1
MRCH1
MIFH1
MRC1