Responding To A Message; Action-Prompting Messages; Error Message - Roland SP-300 User Manual

7-2 Responding to a Message

Action-prompting Messages

These are the main messages that appear on the machine's display
to prompt correct operation. They do not indicate any error. Fol-
low the prompts and take action accordingly.
[CLOSE THE COVER]
Close the front cover and the cover. For safety, the carriage does
not operate while a cover is open.
[SHEET NOT LOADED SETUP SHEET]
Load media. This message appears when an attempt to perform a
printing test was made while no media was loaded.
[1 2 3 4 ]
Only a small amount of ink remains. Replace the cartridge indi-
cated by the flashing number with a new cartridge.
[SET SOL CRT. 1 2 3 4]
Insert the ink cartridge indicated by the flashing number. This
message appears at times such as during cartridge replacement.
[REMOVE SOL CRT. 1 2 3 4]
Remove the ink cartridge indicated by the flashing number. This
message appears at times such as during head cleaning.
[SET SOL CL-LIQUID 1 2 3 4]
Insert the cleaning cartridge indicated by the flashing number. This
message appears at times such as during head cleaning.
[REMOVE SOL CL 1 2 3 4]
Remove the cleaning cartridge indicated by the flashing number.
This message appears at times such as during head cleaning.
[EMPTY DRAIN BOTTLE]
Remove the drain bottle from the machine, discard the collected
ink, then reinstall the drain bottle. Press the [ENTER] key to con-
tinue. This message appears before operations that will discharge
large amounts of ink.
[INSTALL DRAIN BOTTLE]
Make sure that the drain bottle is set in position. Set the drain
bottle in place. Press the [ENTER] key to continue.
[TIME FOR MAINTENANCE]
It is time to clean the printing heads. After checking, press the
[ENTER] key. Go to "5-2 Cleaning the Printing Heads" and refer
to "If Drop-out Persists Even After Carrying Out Cleaning Sev-
eral Times," and perform cleaning promptly.
[TIME FOR WIPER REPLACE]
It is time to replace the wiper. After checking, press the [ENTER]
key. Go to "5-4 Replacing Consumable Parts" and refer to "Re-
placing the Wiper," and perform replacement promptly.
[PRESS THE POWER KEY TO CLEAN]
When the main power switch is left on and the machine remains
unused for about a month, a warning beep sounds and this mes-
sage appears. Refer to "4-7 When Not in Use for a Prolonged Pe-
riod," and perform cleaning.

Error Message

This describes the error messages that may appear on the machine's
display, and how to take action to remedy the problem. If the ac-
tion described here does not correct the problem, or if an error
message not described here appear, contact your vendor or the
nearest Roland DG Corp. service center.
[SHEET SET ERROR SET AGAIN]
The sheet loading lever was lowered while no media was
loaded.
Raise the sheet loading lever, place media at the correct location
on the bed, then lower the lever again. This message appears when
the media is not at the correct location. Refer to "2-3 Loading
Media."
An attempt was made to load media that is too small.
Raise the sheet loading lever, then replace the media with media
of a loadable size.
[EDGE DETECTION] is set to [ENABLE], but transparent
media was loaded.
Raise the sheet loading lever, set the [EDGE DETECTION] menu
item to [DISABLE], then reload the media. (Refer to "6-2 De-
tailed Descriptions of the Menus.")
[PINCHROLL ERROR INVALID RIGHT POS]
The right pinch roller is positioned at a location where it does
not pinch the media.
Raise the sheet loading lever and move the right pinch roller to
the correct location. (Refer to "2-3 Loading Media.")
[PINCHROLL ERROR INVALID LEFT POS]
The left pinch roller is positioned at a location where it does
not pinch the media.
Raise the sheet loading lever and move the left pinch roller to the
correct location. (Refer to "2-3 Loading Media.")
[DATA ERROR CANCELING...]
Output was stopped because a problem was found in the
data received.
Operation cannot be continued. Check for problems with the con-
nector cable or the computer, then redo the operation, starting with
reloading the media.
[SHEET TOO SMALL CONTINUE?]
The size of the data is larger than the printing or cutting
area of the loaded media.
To continue performing output without correcting this, press the
[ENTER] key. At this time, the portion extending beyond the print-
ing or cutting area is not output. To stop output, stop sending data
from the computer, then raise the sheet loading lever. Make the
printing or cutting area wider such as by replacing the media with
a larger piece of media or by changing the positions of the pinch
rollers, then send the data again.
7. What to Do If...
105