Tools Needed For Assembly; Unpacking Instructions - Emerson ST CROIX CF3300AP Owner's Manual

THIS FAN IS SUITABLE FOR DAMP LOCATIONS
SUCH AS COVERED PORCHES, COVERED PATIOS, AND COVERED
DECKS...ANYWHERE THERE IS A ROOF OVERHEAD.

Tools Needed for Assembly

One Phillips head screwdriver
One 1/4" blade screwdriver
One 5/16" open end wrench or pliers
7/16", 1/2" & 9/16" wrench or socket wrench
One 1/4" drill bit
MATERIALS
Wiring outlet box and box connectors must be of type
required by the local code. The minimum wire would
be a 3-conductor (2-wire with ground) of following
size:
For your convenience, check-off boxes are provided next to each step. As each step is completed, place a
check mark in the box. This will insure that all steps have been completed and will be helpful in finding
your place should you be interrupted.
WARNING
!
Do not install or use fan if any part is damaged
or missing. Call Toll-Free:
1-800-654-3545
WARNING
!
This product is designed to use only those
parts supplied with this product and/or any
accessories designated specifically for use
with this product by Emerson Electric Co.
Substitution of parts or accessories not
designated for use with this product by
Emerson could result in personal injury or
property damage.
1. Check to see that you have received the following
parts:
NOTE: If you are uncertain of part description,
refer to exploded view illustration.
NOTE: Blades and downrod kit sold separately.
a. Fan assembly
b. Two fan motor covers
c. One decorative downrod sleeve
d. One upper decorative downrod sleeve
assembly
e. One decorative strap ring
f. One ceiling canopy
g. Four right hand blade flanges
h. Four left hand blade flanges
i. One hanger ball/downrod extension assembly
j. One hanger bracket assembly
k. Eight blade medallions
l. One SW22 wall control with almond and
white knobs
One stepladder
One wire stripper

Unpacking Instructions

3
Installed Wire Length
Up to 50 ft.
50-100 ft.
WARNING
!
Before you assemble your ceiling fan, refer to
section on proper method of wiring your fan
(page 8). If you feel you do not have enough
wiring knowledge or experience, have your fan
installed by a licensed electrician.
m.Mounting bracket bag, containing:
1. One 3/8 x 2" lag bolt
2. One 3/8 x 5" lag bolt
3. Two 3/8" flat washers
4. One brass barrel nut
5. One brass bushing
6. One ceiling support cable
7. Two 5/32 x 10mm phillips screws
n. One hardware bag, containing:
1. Five wire connectors
2. One 1/16" hex wrench
3. One clevis pin
4. One hair pin clip
5. Two threaded studs
6. Two lockwashers
7. Two knurled knobs
8. Two 5/16-18 x 1/4" cup point setscrews
9. One 3/16" hex wrench
o. One flange assembly bag, containing:
1. Seventeen #8-32 x 15mm flat head screws
p. Two blade assembly bags, each containing:
1. Twenty-five #10-32 x 18mm oval head
screws
q. One downrod assembly bag, containing:
1. Nine 1/4 x 10mm round head screws
NOTE: Keep all bags unopened until time of
assembly. Then place the parts from each loose
parts bags in a small container to keep them from
being lost. If any parts are missing, contact your
local retailer or catalog outlet for replacement
before proceeding.
2. Remove the fan assembly from the protective
plastic bag. Place the fan assembly into the foam
pad with the downrod coupling facing up.
The foam pad serves as a holder for the fan during
the first stages of assembly.
Wire Size A.W.G.
14
12
U.L. Model No.: CF3300