Strong SRT 8201 User Manual
  1. Manuals
  2. Brands
  3. Strong Manuals
  4. Receiver
  5. SRT 8201
  6. User manual

Strong SRT 8201 User Manual

Digital terrestrial hd receiver
Hide thumbs Also See for SRT 8201:
Table of Contents

Advertisement

Quick Links

Digital Terrestrial HD Receiver SRT 8201
User manual
Manuel d'Utilisateur
Manuale Utente
Používateľská príručka
Руководство пользователя

Advertisement

Table of Contents
loading

Related Manuals for Strong SRT 8201

Summary of Contents for Strong SRT 8201

  • Page 1 Digital Terrestrial HD Receiver SRT 8201 User manual Manuel d’Utilisateur Manuale Utente Používateľská príručka Руководство пользователя...

  • Page 4: Table Of Contents

    8.0 TRoublEShooTIng 9.0 TEChnICAl SPECIfICATIonS STRong declares that this item complies with the basic requirements and other relevant regulations of directives 2004/108/EC and 73/23/EC, RohS 2002/95/EC Subject to alterations. In consequence of continuous research and development technical specifications, design and appearance of products may change.

  • Page 5: Introduction

    PART 1 • English 1.0 InTRoduCTIon 1.1 Safety Instructions do noT InSTAll YouR RECEIvER: In a closed or poorly ventilated cabinet; directly on top of or under any other equipment; on a surface which might obstruct the ventilation slots. do noT EXPoSE ThE RECEIvER oR ITS ACCESSoRIES: To direct sunlight or any other equipment that generates heat;...

  • Page 6: Equipment Set-Up

    It is advised not to store important information on USB storage devices used with „ „ the receiver. Always make backups of data on your USB storage device before using it with this receiver. STRONG will not take responsibility for any loss of information or circumstances caused by loss of information.

  • Page 7: Your Receiver

    PART 1 • English 2.0 YouR RECEIvER 2.1 dEfAulT PIn: 1234 2.2 front Panel Fig. 1 1. 4 digits display: Indicates current time in STANDBY mode Indicates current channel number in OPERATING mode 2. IR sensor: Point your remote control towards this sensor. 3.

  • Page 8: Connection

    PART 1 • English 11. ok Menu Off: Displays the current channel list Menu On: Activates the highlighted menu item. 12. RECoRd Records the TV programme to the connected USB storage device 13. TImEShIfT Activates the Timeshift function (Off/On) 14. 0~9 Enters a channel number in viewing mode or a value inside the respective menu 15.

  • Page 9: Connecting To A Digital Audio Amplifier With S / Pdif

    PART 1 • English 3.4 Connecting to a digital Audio Amplifier with S / PdIf Fig. 4 By connecting your receiver to a digital amplifier or home theatre system, you can enjoy the best possible sound quality and multi-channel audio (depending on broadcast). Connect your Digital Audio Amplifier or home theatre system with a suitable cinch cable to the S / PDIF connector on the back of the receiver.

  • Page 10: Quick Guide To Using Your Receiver

    5.0 QuICk guIdE To uSIng YouR RECEIvER We at STRONG understand that you can’t wait to enjoy your new high definition digital terrestrial receiver. The following quick guide will make you familiar with the basic operation of this device. We do, however, advice you to read the full manual to get the best performance from your receiver.

  • Page 11: Operation

    PART 1 • English 6.0 oPERATIon Your new receiver is equipped with several features to make watching TV a true pleasure. This paragraph describes these features. Please also read chapter 7.0 to get familiar with the menu of your receiver. 6.1 Changing channels Following ways are possible for changing channels with your new receiver: Via direct access using the 0~9 buttons.

  • Page 12: Teletext

    PART 1 • English 6.4 Teletext Your receiver includes a fully featured Teletext. To access Teletext, press the TTX button in viewing mode and use the 0~9 buttons to input the number of the page you wish to see. The coloured buttons of the remote control allow you to jump to selected pages directly, as indicated on the bottom of the Teletext screen.

  • Page 13: Main Menu

    PART 1 • English At the beginning of the recording a recording sign will be shown for a short while on the upper left corner of your TV screen. To stop the recording, press 3. Select Yes and press ok again to stop the recording.

  • Page 14: Skipping Channels

    PART 1 • English 7.1.1.3 Skipping channels Channels marked with Skip will be skipped when zapping channels with the pq buttons. The channels will still be available from the channel list. To mark channels for skipping, press gREEn while in TV Channel List. Use pq to select a channel and press ok to mark or unmark it for skipping.

  • Page 15: Installation

    PART 1 • English 7.1.2 Radio Channel list Basically, the operation of the Radio Channel List is the same as in the TV Channel List. The only difference is that in Radio Channel List there is no video information, so it will always display the radio background on the preview screen.

  • Page 16: System Setup

    PART 1 • English Select Off for passive antennas. When set to On, 5 V will be present on the ANT IN connector of the receiver. Press EXIT to leave the Antenna Power menu. 7.2.4 lCn (logical Channel numbering) If LCN (Logical Channel Numbering) is activated and an LCN signal is provided by the operator, channels will be stored in an operator defined order.

  • Page 17: Local Time Setting

    PART 1 • English Connection: Use this option to select the connection to your TV set. Select HDMI or TV SCART. If connection type HDMI is selected, then only the CVBS signal is available on the TV SCART. Digital Audio Output: Toggles between PCM and Bitstream output.

  • Page 18: Tools

    This submenu shows receiver specific information such as hardware version and software version. It also displays our web address www . strong . tv. Please have the Information screen on hand when you call our hotline. The person who answers your call might ask for the information given in this screen.

  • Page 19: Media

    This receiver is equipped with an Over The Air software upgrade function. An Over The Air update might not be available in your region. Please visit our website www . strong . tv or contact your local service hotline for more information about this option.
  • Page 20 PART 1 • English Use the buttons like described below in order to choose functions during the different playback modes (like described in the help banner below): video: Info: Press the Info button to set repeat mode. The options are repeat folder folder icon/repeat once 1 or no repetition (no icon shown).

  • Page 21: Hdd Information

    Formatting will permanently delete ALL data stored on the connected device. Please make a backup copy of all data you wish to keep before entering the HDD Format menu. STRONG cannot be held responsible for loss of data from USB devices used with this receiver.

  • Page 22: Remove Usb Device Safely

    PART 1 • English 7.5.3 dvR Setting This menu allows you to configure settings for Timeshift, recording and playback. Select DVR Setting in the Media menu and press ok to enter. Use pq to move the highlight and tu to change settings. Timeshift: Select between Auto, Pause or Off.

  • Page 23: Troubleshooting

    Default PIN is 1234 Forgotten channel lock code Contact local Service Hotline or send email to our Support via www . strong . tv After moving the receiver to Antenna signals are too weak Press the INFO button on another room/area you are no...

  • Page 24: Technical Specifications

    PART 1 • English Problem Possible cause What to do Playback of video (or Timeshift) Read/write speed of your USB Make sure to use a USB storage is causing picture freeze/macro device could be too low. device with sufficient speed blocks or similar distortion, and space.
  • Page 25 MP3 and OGG Picture view: BMP and JPEG *STRONG cannot guarantee the playback of video files although extensions are listed, as it depends on codec used, data bit rate and resolution (all MPEG codec formats are supported). Connectors ANT IN - IEC Female ANT OUT - IEC Male TV SCART (RGB, CVBS, Audio L&R)

Table of Contents