Related Manuals for LifeSpan C3-DT
Summary of Contents for LifeSpan C3-DT
-
Page 1: Owners Manual
Desktop Cycle Owners Manual For safe use and product knowledge, please completely read this Product OWNERS MANUAL. v. 1.0... - Page 3 C3-DT Desktop Cycle desktop cycle cycle desktop cycle desktop cycle desktop cycle LifeSpan...
- Page 4 Welcome Warranty Important Safety Precautions Starting an Exercise Program Assembly Instructions Leveling and Moving Seat Adjustments Engineering Mode, Troubleshooting and Maintenance Serial Number Information...
- Page 5 C3-DT Desktop Cycle The LifeSpan C3-DT Desktop Cycle comes with the following warranty, which applies only for home use. Valid in the US and Canada only. (6 hr/day) Warranty Lifetime 2 Years 1 Years LifeSpan LifeSpan as outline above The customer may be responsible to pay for the Service Technician’s travel time where travel in excess of 20 miles (32 km) is required.
- Page 6 C3-DT Seat Molded, contoured seat Seat Adjustment Height - 19 positions Resistance System Magnetic - Eddy Current Pedals Self balancing 18 lbs (8 kg) 400 lbs (181 kg) 22” W x 28” L (55cm W x 71cm L) Rear Mounted...
- Page 7 C3-DT Desktop Cycle If an object falls into an opening, unplug the power cord from the outlet. Remove the object or call customer service. bike bike (3m)
- Page 9 C3-DT Desktop Cycle Since your upright cycle is a heavy piece of equipment it is recommended you use two people during assembly and follow these assembly instructions to reduce any problems that could occur. Item# description Main Frame Front Support...
- Page 10 Hardware Located in hardware bag M8*75L Bolt M8 Curved Washer 2pcs 2pcs Multi-wrench - Allen wrench - 5 mm 10, 13, 14, 15, 17, 22 mm Pre-installed hardware Hardware will need to be removed and re-installed during the installation process M8 Washer M8*16L Bolt M8 Curved Washer...
- Page 11 C3-DT Desktop Cycle Step 1: Remove Components from Box B. Locate the hardware bag. Step 2: Rear Support Assembly A. P lace the main frame assembly (1) on a solid level surface. It may be necessary to prop the back of the frame up slightly to give clearance for step B.
- Page 12 Step 3: Seat Post Assembly Pull on the seat post adjustment knob (M) to release the locking pin and slide the seat post (4) down into the seat post tube (L). When the desired height is reached, release the seat post adjustment knob (M) to allow the locking pin to engage.
- Page 13 C3-DT Desktop Cycle Step 5: Front Support Assembly A. Adjust the seat post so it is at the highest setting. B. Tilt the bike back until it is resting on the seat and the rear support assembly (as shown below.) C.
- Page 14 Step 6: Right and Left Pedal Assembly A. Identify which pedal goes on the right side and which goes on the left side by locating the “R” on the bolt of the right pedal (6) and the “L” on the bolt of the left pedal (7). B.
- Page 15 C3-DT Desktop Cycle Your C3-DT cycle comes with two leveling feet (P) in the front and two stationary feet (Q) in the rear. Gently cycle our C3-DT cycle is equipped with two transport wheels (R) located on the rear support. Move the wire that is coming from the bottom of the frame to the console so it will not get pinched when moving the cycle.
- Page 16 Seat Height Adjustments Your C3-DT cycle allows for 19 positions of height adjustment. To adjust the seat, turn the seat post adjustment knob (M) counterclockwise 2 full turns. Pull the knob out and adjust the seat height to the desired position. Once the desired position is reached, release the seat post adjustment knob and slide the seat up or down until the knob pops back into one of the designated positions.
- Page 17 Disconnect and reconnect power to the cycle. front Also check the console wire harness to make sure it has not come loose. If still a problem contact LifeSpan Customer Service. If everything is tight, contact LifeSpan Customer Service for replacement pedals...
- Page 19 C3-DT Desktop Cycle...
- Page 20 - C3-DT DESKTOP CYCLE MODEL MADE IN TAIWAN...