Omega RD100B User Manual page 62

D/M/Y: (example) 31/08/2005
D.M.Y: (example) 31.08.2005
M.D.Y: (example) Aug.31.2005
Query XN?
Example Set to the "2005/08/31" format.
XN Y/M/D
Description This setting applies to the format of the date
shown on the display and the date printed on the
periodic printout, manual printout, alarm printout,
message printout, recording start printout, and
new chart speed printout.
Note
How this setting applies to the time printout format of the
alarm printout, message printout, recording start printout,
and new chart speed printout: The setting specifies the
format of the "M/D" and "Y/M/D" section when the time
printout format is set to "M/D H:M," "M/D H:M:S," or "Y/M/
D H:M:S."
XT Selects the temperature unit.
Syntax XT p1<terminator>
p1 Temperature unit
C °C
F °F
XT?
Query
Example Use °F.
XT F
UF Sets whether to use the
extended functions.
UF p1,p2,p3,p4<terminator>
Syntax
p1 Bias function (USE, NOT)
p2 Square root low-cut function (USE, NOT)
p3 1-5V input low-cut function (USE, NOT)
p4 Alarm delay function (USE, NOT)
Query UF?
Example Use all the extended functions.
UF USE,USE,USE,USE
Description • The input offset is set using the VB command.
• The low-cut function is set using the SR
command.
• The delay alarm is set using the SA and BD
commands.
UT Selects the time printout format.
UT p1,p2,p3,p4<terminator>
Syntax
p1 Time printout format of the alarm printout
The available selections are the same as
those of p2. None is not available.
p2 Time printout format of the message printout
HH:MM
Hour:Minute
HH:MM:SS Hour:Minute:Second
M/D H:M Month Day Hour:Minute
M/D H:M:S Month Day Hour:Minute:
Second
4.5 Basic Setting Commands
YMD H:M:S Month Day Year Hour:Minute:
Second
None No time printout
p3 Time printout format of the record start time
printout
The available selections are the same as
those of p2. None is not available.
p4 Time printout format of the new chart speed
printout
The available selections are the same as
those of p2. None is not available.
Query UT?
Example Set the all time printouts to Hour:Minute format.
UT HH:MM,HH:MM,HH:MM,HH:MM
XR Sets the remote control input
(/R1 option).
Syntax XR p1,p2<terminator>
p1 Remote control input terminal number (1 to
5)
p2 Action
NONE
Record On/Off
Chart speed
Time adjust
Math start/stop Start/Stop
Math reset
Manual print
Alarm Ack
Message1
Message2
Message3
Message4
Message5
Query XR[ p1]?
Example Assign the printout of message 2 to the remote
control input of terminal number 1.
XR 1,Message2
Description Math start/stop and Math reset can be specified
on models with the computation function (/M1
option).
YS Sets the RS-422A/485 interface
(/C3 option).
YS p1,p2,p3,p4,p5<terminator>
Syntax
p1 Address (1 to 32)
p2 Baud rate (1200, 2400, 4800, 9600, 19200,
38400)
p3 Data length (7, 8)
p4 Parity check (ODD, EVEN, NONE)
p5 Protocol (NORMAL, MODBUS)
4
No action
Start/Stop recording.
Change the chart
speed.
Reset the internal
clock to the nearest
hour.
computation.
Reset computation.
Execute manual print.
Execute alarm
acknowledge.
Print message 1
Print message 2
Print message 3
Print message 4
Print message 5
4-21