Related Manuals for Peco WavePRO K2500-001
Summary of Contents for Peco WavePRO K2500-001
- Page 1 WavePRO Wireless Programmable T2500 Thermostat & R2500 Receiver OPERATING MANUAL Model K2500-001...
-
Page 2: The Peco Wavepro Wireless System
Thank you for choosing the PECO WavePRO Wireless System (Model K2500-001). The PECO WavePRO Wireless System is a wireless thermostat transmitter and receiver. It is designed for use with conventional (gas, oil, electric) or heat-pump systems. It can support up to 2-HEAT/ 2-COOL confi... -
Page 3: T2500 Thermostat
Product Specifi cations (Model K2500-001) Temperature Range: 50° to 90° F (10° to 32° C) Differential: 1° F (0.5°C) T2500 Thermostat: Two AA alkaline batteries or 24 VAC, 50/60 Hz Input Power R2500 Receiver: 24 VAC, 50/60 Hz Wireless Type 902 to 928 MHz Band, Frequency Hopping Spread Spectrum (FHSS) Wireless Range 100 feet (30.48 meters) typical reliable range in open air... -
Page 4: Table Of Contents
TABLE OF CONTENTS The PECO WavePRO Wireless System ....................2 T2500 THERMOSTAT Front panel display reference: T2500 thermostat ................6 Button operation ..........................7 The T2500 display ..........................10 The T2500 display menus ......................... 11 Set the time and day ......................... 14 Selecting the Fahrenheit or Celsius temperature ................ - Page 5 • This product, when installed, will be part of an engineered system whose specifi cations and performance characteristics are not designed or controlled by PECO. You must review your application and national and local codes to assure that your installation will be functional and safe.
-
Page 6: Front Panel Display Reference: T2500 Thermostat
FRONT PANEL DISPLAY REFERENCE: T2500 THERMOSTAT Following are the T2500 thermostat Display and buttons: AUTO Display HEAT COOL UP ▲and SETBACK Auto ON DOWN ▼ HOLD MTUWTHFSASU DFLTSLEEP COPY buttons PROGRAM SYSTEM button button FAN button... -
Page 7: Button Operation
(To appear, SETBACK must be selected in “Advanced confi guration.” See the “PECO WavePRO Wireless System Installation Guide”). NOTE: The SYS button is also used to scroll through the Service Menu in advanced confi guration.(see “Advanced confi guration” in the “PECO WavePRO Wireless System Installation Guide”). - Page 8 BUTTON OPERATION Fan Button The FAN button is used to control the fan mode. Pressing FAN will light up the two fan mode options described below. Press FAN to scroll through the options. As you scroll, the “fl ashing” option is automatically selected. The T2500 thermostat times out and automatically saves the “fl...
- Page 9 BUTTON OPERATION SET – Initiates the time and temperature schedule for a particular day or group of days. ® Allows you to reset the thermostat to the factory default ENERGY STAR program. (see “Programming the T2500”). COPY – Copies one day’s schedule to another day or to another group of days (see “Programming the T2500”).
-
Page 10: The T2500 Display
THE T2500 DISPLAY Figure 1 below illustrates the various display menus in the T2500 display. The menus are: System Mode Display Programming Commands Program Override Commands Temperature Display Time Period Indicators Service Indicator Time & Day Display Fan Operation Indicators Figure 1. -
Page 11: The T2500 Display Menus
SETBACK – Indicates the heating or cooling system is operating in manual setback mode. (To appear, SETBACK must be selected in “Advanced confi guration.”See the “PECO WavePRO Wireless System Installation Guide”). Temperature Display Default display: Digits display the current room temperature. - Page 12 THE T2500 DISPLAY MENUS (CONT.) 24Hr – Lights up during programming to indicate time will be displayed in 24-hour clock format. AM / PM – Indicates 12-hour clock format. Programming Commands SET – Enters thermostat into custom program mode which allows you to specify a unique times and temperatures for a particular day or group of days.
- Page 13 THE T2500 DISPLAY MENUS (CONT.) Program Override Commands HOLD – Indicates thermostat is in a Temporary or Permanent Hold. (Programmed settings are off, but they are not lost.) HOLD HRS – During programming, lights up in conjunction with clock digits; allows program to be put on Temporary Hold for up to 24 hours.
-
Page 14: Set The Time And Day
SET THE TIME AND DAY 1. Press PROG to show program options. 2. Press ▲or ▼to scroll until “CLOCK” is fl ashing. To select, press PROG once. 3. Press ▲or ▼to scroll through “24Hr”, “AM”, “PM” options. “24Hr” sets your thermostat to a 24-hour clock. -
Page 15: Selecting The Fahrenheit Or Celsius Temperature
SELECTING THE FAHRENHEIT OR CELSIUS TEMPERATURE Set the temperature display using the following simple steps. Settings are saved automatically after you exit the PROG mode. 1. Press PROG once. 2. Press ▲or ▼to scroll until BOTH “°F/°C” are fl ashing. 3. -
Page 16: Programming The T2500
PROGRAMMING THE T2500 Each day has four scheduled periods (WAKE, DAY, EVE, and SLEEP ). Each one of the periods has a start time and heat and cool setpoints. Heat Setpoint controls system heating during cold weather. Cool Setpoint controls the cooling system during hot weather. (Your thermostat is preprogrammed to function with the ENERGY STAR settings.) Factory Program: The T2500 is preprogrammed with seven days of the week: Time Period... -
Page 17: Custom Program
CUSTOM PROGRAM The T2500 can be programmed with settings for each day individually, for Monday through Friday, for Saturday and Sunday, or for all seven days as identical. Follow this step-by- step procedure. 1. Press PROG once. 2. Press ▲or ▼to scroll until “SET” is HOLD fl... - Page 18 CUSTOM PROGRAM (CONT.) The Day/Group of Days are: 5. Select one of the following options. 7- Day Individual Programming : Each day fl ashes individually. Select: “M,” Monday; “TU,” Tuesday; “W,” Wednesday; “TH,” Thursday; “F,” Friday,“SA,” Saturday, and “SU,” Sunday. You must program four periods for each day.
- Page 19 CUSTOM PROGRAM (CONT.) 6. To select your preference, press PROG once. 7. Press ▲or ▼to scroll through the four time periods (WAKE, DAY, EVE, and SLEEP). Select the time period to be programmed and press PROG once. 8. Press ▲or ▼to scroll to the desired starting hour.
- Page 20 CUSTOM PROGRAM: COPY FEATURE You may also copy and paste all of an individual day’s settings to another day or to another group of days. 1. Press PROG once. 2. Press ▲or ▼to scroll until “COPY” is fl ashing. 3. Press PROG once to select “COPY”. 4.
- Page 21 CUSTOM PROGRAM (CONT.) Time & Temperature Programming Example In this example, the thermostat user wants to program the weekend with a schedule different from the Factory Program. The user wants the Saturday and Sunday program to be identical. 1. Press PROG once. 2.
-
Page 22: Overriding The Program
OVERRIDING THE PROGRAM The T2500 thermostat’s HOLD feature allows you to put the thermostat in Temporary Hold or Permanent Hold. HOLD will override programmed settings but does not lose them. 1. Press PROG once. 2. Press ▲or ▼to scroll until “HOLD” is fl... - Page 23 OVERRIDING THE PROGRAM (CONT.) Setting up a Permanent Hold: 1. Press PROG once. 2. Press ▲or ▼to scroll until “HOLD” is fl ashing. To select, press PROG once. 3. Press ▲or ▼to scroll to “ON”. To select, press PROG once. Note: The thermostat is now on hold until you manually turn off the hold.
-
Page 24: Fcc Compliance
PO Box 82189, Portland, OR 97282 www.pecomanufacturing.com © Copyright 2010. PECO, Inc. All Rights Reserved. P/N 70161 3220-2216 REV 0 PECO is a registered trademark of PECO, Inc. The PECO logo is a trademark and/or service mark of PECO, Inc.