Follett 25 Installation, Operation And Service Manual page 18

§ Wear rubber gloves and safety goggles (or face shield) when handling cleaner or sanitizer mixtures.
§ Use only Follett approved cleaners.
§ It is a violation of Federal law to use Solution A or Solution B in a manner inconsistent with their labeling.
§ Do not use solvents, abrasive cleaners, metal scrapers or sharp objects to clean any part of the dispenser.
Solution A: Following manufacturer's instructions, mix cleaning solution of 1 gal. (3.8 L) 120 F (49 C) water and 7 oz.
(198 g) (one 7 oz. packet) of Follett SafeCLEAN™ ice machine cleaner/descaler (P/N 00132001).
Solution B: Following manufacturer's instructions, mix a sanitizing solution of 1 gal. (3.8 L) 120 F (49 C) water and
1.6 oz. (47 ml) Nu-Calgon IMS-II Sanitizer (P/N 00979674).
Clean/descale and sanitize ice machine (if applicable)
§ Units with ice machines require ice machine cleaning/descaling and sanitizing at least every 6 months, and more often
if conditions dictate. Cleaning/descaling and sanitizing the ice machine will result in better performace and extend ice
machine life. Refer to Ice Machine Operation and Service Manual for specifi c instructions.
Clean/descale dispenser
1. Remove and discard all ice from storage hopper.
2. Ensure power is disconnected. Working inside storage area, remove center thumbscrew from dispense wheel,
tilt wheel up toward back to clear baffle and disengage wheel from motor shaft.
3. Remove dispense chutes.
4. Thoroughly wipe lid, dispense wheel, baffle and dispense chutes with cloth soaked in Solution A.
5. Wipe all bin surfaces (including the area under dispense wheel) with a damp cloth wrung out in Solution A.
Note: To avoid possible damage to dispense motor assembly, use only a damp cloth to clean the storage bin. Do not
allow water to run through bottom of bin area.
6. Remove grille and wash with Solution A. Rinse thoroughly with clean water.
7. Rinse all above items with damp cloth wrung out in clear water.
Sanitize dispenser
8. Wipe all above items with damp cloth wrung out in Solution B to sanitize. Do not rinse.
9. Reinstall all parts and replace any panels removed prior to cleaning.
10. Pour 1 gal. (3.8 L) of hot tap water into drain pan to fl ush drains.
11. If the dispenser is equipped with a Chilled Water Accessory continue to Step 11.1; if not, skip to Step 12.
11.1 Remove four screws securing splash panel.
11.2 Disconnect 3/4" (19mm) drain line from bottom of chilled water canister.
11.3 Loosen (do not remove) screw securing front bracket of chilled water canister to bottom of dispenser
hopper.
11.4 Rotate canister clockwise to release front bracket, then pull canister forward to disengage rear bracket.
11.5 Remove chilled water coil from canister and clean with cloth wrung out in Solution A.
11.6 Wipe inside of chilled water canister with cloth wrung out in Solution A.
11.7 Rinse all above items with damp cloth wrung out in clear water.
11.8 Sanitize all above items with damp cloth wrung out in Solution B. Do not rinse.
11.9 Reinstall chilled water coil into canister (rubber alignment grommet on coil tubing must be located outside
chilled water canister to hold coil securely against canister wall).
11.10 Reinstall chilled water assembly on dispenser and tighten screw securing front bracket.
11.11 Reconnect 3/4" (19mm) drain line to chilled water canister.
11.12 Reinstall splash panel and top front cover.
12. If so equipped, turn ice machine ON and begin to make ice (ice machine should start immediately with power
and bin signal supplied).
13. After approximately 30 minutes, test dispenser for proper dispensing.
18
CAUTION!
25/50 Series 220 V 60 Hz/230 V 50 Hz Dispensers