Icom IC-41W Instruction Manual
  1. Manuals
  2. Brands
  3. Icom Manuals
  4. Transceiver
  5. IC-41W
  6. Instruction manual

Icom IC-41W Instruction Manual

Uhf c.r.s. transceiver
Hide thumbs
Table of Contents

Advertisement

Quick Links

INSTRUCTION MANUAL
UHF C.R.S.TRANSCEIVER
i41W

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the IC-41W and is the answer not in the manual?

Questions and answers

Related Manuals for Icom IC-41W

Summary of Contents for Icom IC-41W

  • Page 1 INSTRUCTION MANUAL UHF C.R.S.TRANSCEIVER i41W...

  • Page 2: Explicit Definitions

    ‘overlap.’ Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incor- porated (Japan) in Japan, the United States, the United Kingdom, Germany,...

  • Page 3: Precautions

    Use and charge only specified Icom bat- attachment. Exposing the inside of the transceiver to dust or tery packs with Icom radios or Icom chargers. Only Icom bat- water will result in serious damage to the transceiver. tery packs are tested and approved for use with Icom radios...
  • Page 4 PRECAUTIONS (Continued) BE CAREFUL! This device complies with Standard Aus- The IC-41W meets IP67* requirements tralia Specification No. AS/NZS 4365-2002 for dust-tight and waterproof protection. However, once the and AS/NZS 4295: 2004. transceiver has been dropped, dust-tight and waterproof pro- tection cannot be guaranteed because of possible damage to the transceiver’s case or the waterproof seal.

  • Page 5: Table Of Contents

    TABLE OF CONTENTS IMPORTANT ................i Priority Channel ...............10 ■ EXPLICIT DEFINITIONS .............i To set the Priority Channel ..........10 GENERAL INFORMATION ............i To switch to the Priority Channel .........10 PRECAUTIONS ................ii To cancel the Priority Channel ........10 TABLE OF CONTENTS ............. iv Monitor ................10 ■...

  • Page 6: Table Of Contents

    TABLE OF CONTENTS (Continued) 6 SCAN ................17–20 9 OTHER FUNCTIONS ............28–30 Scanning Preparation ............17 Smart Ring/ATS ............28 ■ Scan type selection .............17 RX Frequency ..............29 Tag Channel Setting ............17 PTT Hold ..............30 Scan Resume Condition ..........18 10 BATTERY CHARGING ..........31–35 Open Scan ...............18 ■...

  • Page 7: Accessories

    ACCESSORIES Supplied Accessories Battery Pack ■ To attach the battery pack: Slide the pack in the direction of the arrow (q), until the bat- Battery pack Battery charger AC adapter tery release button makes a ‘click’ sound. (for the battery charger) NOTE: Push on the bottom of the pack to make sure the release button is firmly locked.

  • Page 8: D Belt Clip

    ACCESSORIES Jack cover Belt Clip To attach the jack cover: To attach the belt clip: q Attach the jack cover to the [MIC/SP] jack. Release the battery pack if it is attached. w Tighten the screws. Slide the belt clip in the direction of the arrow (see below) until a ‘click’...

  • Page 9: Unit Description

    UNIT DESCRIPTION Front panel e SIDE1 KEY [Side1] ■ In Normal mode Push to toggle the monitor (open tone squelch) func- ➥ tion ON or OFF. (p. 10) Push and hold for 2 seconds to activate the following ➥ functions in order: Speaker •...
  • Page 10 UNIT DESCRIPTION i LCD DISPLAY (p. 5) !1 PRIO/SET.P KEY In Normal mode o SCAN/TAG KEY Push to change the selected channel to the priority ➥ In Normal mode channel. (p. 10) Push to start or stop scanning. This is dependent on ➥...

  • Page 11: Display

    UNIT DESCRIPTION Display ■ t BELL INDICATOR Appears when the pocket beep function is in use. ➥ (p. 23) Blinks when the specified selcall or smart ring call is ➥ received. (pp. 26, 28) y QUIET INDICATOR Appears when the quiet function is ON. (p. 27) u PRIORITY CHANNEL INDICATOR Appears when the priority channel is set.

  • Page 12: Unit Description

    UNIT DESCRIPTION !2 LOW POWER INDICATOR Appears when low output power is selected, or the unit ➥ is operating in dry (alkaline) battery mode. When the battery power decreases below the specified ➥ level, the unit will switch to low power automatically. !3 OPEN SCAN INDICATOR Appears when open scan is selected.

  • Page 13: Basic Operation

    BASIC OPERATION Turning the Power ON Battery type ■ ■ Prior to using the transceiver for the first time, the battery The transceiver can be used with the supplied Li-ion battery pack must be fully charged for optimum life and operation. pack or the optional battery case with third party AA batter- ies.

  • Page 14: Backlight

    UHF CB band also help to allow clear, uninter- To enter set mode, push and hold [Top] for 2 seconds, then rupted communication. The IC-41W can access all 80 channels release. on the UHF CB band, as well as designated repeater channels.

  • Page 15: Receiving/Transmitting

    BASIC OPERATION Receiving/Transmitting • Transmit inhibit function – The transceiver will restrict ■ transmission under the following conditions: - The channel is busy, or different CTCSS/DTCS code is NOTE: Transmitting without an antenna may damage the received. (depending on the transmission lockout function transceiver.

  • Page 16: Priority Channel

    BASIC OPERATION Priority Channel Monitor ■ ■ The priority channel allows the user to have quick access to a The monitor function opens the squelch or tone squelch, al- specific channel. Only one channel can be set as the Priority lowing weak signals to be received.

  • Page 17: Set Mode

    SET MODE When in the Set Mode: The Set Mode allows the user to change various settings in the transceiver to suit their operating requirements. Available Push [Top] to select the desired item. settings may differ, depending on the preprogramming of the Push [CH Up] or [CH Down] to adjust the setting.

  • Page 18: D Squelch

    SET MODE Squelch Auto Power OFF In order to receive signals clearly, the squelch level can be The transceiver can be set to automatically turn off after a set adjusted to suit the operating environment. This eliminates period of inactivity (i.e. no key has been pushed). This can be background noise when there are no signals present.

  • Page 19: D Beep

    SET MODE Beep Battery Voltage By default, confirmation beep tones are turned on. This can The transceiver can be set to display the remaining battery be toggled ON or OFF by the set mode, for silent operation. charge for a 2 second period after being turned ON. Battery voltage Battery voltage ON Beep tone ON (default)

  • Page 20: Dtot (Time-Out Timer)

    SET MODE TOT (Time-Out Timer) Scan Resume Timer The time-out timer limits the length of one continuous trans- The scan resume condition can be set as a pause (P5) or mission. This helps conserve battery charge in the event of timer scan (15/10/5).

  • Page 21: D Own Id

    SET MODE Own ID This function allows the user to edit their own ID (this function is inactive by default, and can be turned on via dealer program- ming). Own ID is useful in commercial applications to allow organisations to track where transmissions originate from. To edit: When in set mode, and own ID has been selected, push and hold...

  • Page 22: Repeater Operation

    REPEATER OPERATION Repeater Operation ■ To access the repeater channels: Repeaters extend the operational range of the transceiver by Use the [CH Up] and [CH Down] keys to select a repeater ➥ amplifying received signals. They are usually located on the channel.

  • Page 23: Scan

    SCAN Tag Channel Setting The IC-41W has four scan types, a tag function and four re- sume conditions. Scanning allows the transceiver to automat- Setting channels as ‘tag’ channels allows them to be included in the scan function. ically scroll through all or selected channels in order to find a transmission.

  • Page 24: D Scan Resume Condition

    SCAN Open Scan Scan Resume Condition ■ The scan resume condition can be set as a pause (P5) or timer scan (15/10/5). When a signal disappears, scanning will The open scan function scans for transmitted signals, making resume after 5 seconds, regardless of the setting. it easier to locate new stations for contact or listening pur- poses.

  • Page 25: Group And Priority Scan

    SCAN Group and Priority Scan ■ Group and priority scans repeatedly watch a priority chan- Set the priority channel by holding down for 2 sec- nel while scanning the specified tag channels. This is useful onds while on the desired channel. when waiting for a call on the priority channel.

  • Page 26: Repeater

    SCAN Repeater Repeater search scan flow ■ The repeater search scan is not only used to search for a sig- nal on the repeater channels, but also to access a repeater by Searches for sig- Scan start transmitting automatically in sequence. The repeater search Scan nal on the repeater channel...

  • Page 27: Tone Squelch

    The IC-41W is equipped with both CTCSS t Repeatedly push [CH Up] and [CH Down] to set the de- (Continuous Tone-Coded Squelch System) and DTCS (Digi- sired CTCSS tone frequency/DTCS code.
  • Page 28 TONE SQUELCH • Available CTCSS tone frequency list (Hz) • Available DTCS code list Code Code Code Code Code Freq. Freq. Freq. Freq. Freq. 67.0 94.8 136.5 177.3 218.1 69.3 97.4 141.3 179.9 225.7 71.0 100.0 146.2 183.5 229.1 71.9 103.5 151.4 186.2...

  • Page 29: D Turning The Tone Squelch Operation On Or Off

    TONE SQUELCH Turning the tone squelch operation Setting up and using the pocket Beep ON or Select the desired channel (excluding channel 5 or 35) Select the desired channel (excluding channel 5 or 35) us- using the [CH Up] and [CH Down] keys. ing the [CH Up] and [CH Down] keys.

  • Page 30: Selcall (Selective Calling)

    SELCALL (Selective Calling) To select a TX code channel In addition to tone squelch operation for silent stand-by, Sel- Call operation is available. In tone squelch operation, there Select the desired CB channel (CB-XX) except channels are 155 tone/code options when making a call. SelCall offers 5 and 35.

  • Page 31: Dtx Code Number Edit

    SELCALL (Selective Calling) TX code number edit u Repeat step t and y to input all digits. “ ” enables the user to change the TX code digits contained i After setting the final digit, push to set the code and in the TX code channel.

  • Page 32: Receiving

    SELCALL (Selective Calling) Receiving ■ Receiving an individual call (default setting) Recalling a memorised receive selcall code “PiRo” beeps sound. Push [Top] to enter the function mode, then push and hold ➥ for 2 seconds to display the memorised RX code. The received code channel name/number is displayed ➥...

  • Page 33: Quiet Mode

    SELCALL (Selective Calling) Quiet Mode Stun ■ ■ When quiet mode is turned ON, selcall mute is activated and When a specified ID, set as a kill ID, is received, the stun ➥ allows silent operation until a selcall code is received. Push function is activated (PC programming is required).

  • Page 34: Other Functions

    Icom unit is in range, which is useful in convoy situations rounding communication area. When an RX channel is where groups may be separated.

  • Page 35: Drx Frequency

    OTHER FUNCTIONS RX Frequency To program the RX frequencies: The frequency of the RX channels can be re-programmed Select the desired RX channel (RX-XX), once enabled. within the 450–520 MHz frequency range, to allow the trans- Push [Top] to enter function mode, then push and hold ceiver to listen to communications outside the standard CB [Top] for 2 seconds to enter the RX VFO mode.

  • Page 36: Dptt Hold

    OTHER FUNCTIONS D RX Frequency PTT Hold To program the RX frequencies: (Continued) The PTT switch can be operated as a one touch PTT switch (each push toggles between transmit/receive). Using this y Edit the desired digit with [CH Up] and [CH Down]. function makes it possible to transmit without holding down the PTT switch.

  • Page 37: Battery Charging

    Icom radios or Icom charger. Only Icom battery water, or any other liquids. Never charge or use a wet battery. packs are tested and approved for use and charge with Icom If the battery gets wet, be sure to wipe it dry before using.

  • Page 38: D Charging Caution

    If R DANGER! NEVER charge the battery pack in areas with any of these conditions occur, contact your Icom dealer or extremely high temperatures, such as near fires or stoves, distributor.

  • Page 39: Rapid Charging With The

    BATTERY CHARGING Rapid charging with the BC-160 Optional battery chargers ■ ■ AD-106 installation The BC-160 provides rapid charging of the Li-ion battery packs. The AD-106 must be installed into the BC- charger adapter Charging period: Approximately 3.5 hours. 119N or BC-121N before battery charging. The following items are additionally required: •...

  • Page 40: Bc-119N+Ad-106 Rapid Charging With The Bc-119N

    BATTERY CHARGING Rapid charging with the BC-119N+AD-106 Rapid charging with the BC-121N+AD-106 The optional BC-119N provides rapid charging of the Li-ion The optional BC-121N allows up to 6 battery packs to be battery pack. charged simultaneously. Charging period: Approximately 3.5 hours. Charging period: Approximately 3.5 hours.

  • Page 41: Battery Charging

    BATTERY CHARGING IMPORTANT: Battery charging caution Ensure the guide tabs on the battery pack are correctly aligned with the guide rails inside the charger adapter. (This illustration is described with the BC-160) Tabs Guide rail...

  • Page 42: Options

    OPTIONS MB-93 contents ■ r Clip the belt clip to a part of your belt. And insert the transceiver into the belt clip until the base clip inserted Qty. fully into the groove. q Belt clip ��������������������� 1 w Base clip �������������������� 1 Attaching ■...

  • Page 43: Detaching

    OPTIONS Detaching ■ q Turn the transceiver upside down in the direction of the w Release the battery pack if it is attached. (p. 1) arrow and pull out from the belt clip. e Pinch the clip (q), and slide the base clip in the direction of the arrow (w).

  • Page 44: Optional Hm-168Lwp Description

    OPTIONS Optional HM-168LWP description Attachment ■ ■ Attach the connector of the speaker-microphone into the [SP Alligator type clip MIC] jack on the transceiver and tighten the screws with fin- To attach the speaker-mic. gers. to your shirt or collar, etc. NOTE: Use only your fingers instead of tools to tighten the screws.

  • Page 45: Dbattery Pack

    • MB-93 swivel belt clip • MB-94 belt clip Icom is not responsible for the destruction or damage to an Icom Exclusive alligator-type belt clip. transceiver in the event the Icom transceiver is used with equipment • MB-96N/96F leather belt hanger...

  • Page 46: Specifications

    • External speaker connector • Power supply requirement : 7.2 V DC nominal* (negative ground) All stated specifications are subject to change without *Specified Icom’s battery pack only notice or obligation. • Frequency stability : ±2.5 ppm (–30°C to + 60°C) : 50 Ω...

  • Page 47: Warranty And Registration

    (i.e. battery, antenna, battery chargers etc) ranty claim. Icom (Australia) Pty. Ltd. will, at its discretion, and subject to the terms and If the requested repairs or services are within the terms of warranty, conditions stated below, repair or replace any goods or component parts your equipment will be returned after repair (prepaid) to any desig- which after examination are found to be defective.
  • Page 50 P/Code : Purchasers Address: Email: Phone No: Occupation: Answering the following question will help us to meet your future needs: In what media have you seen Icom products advertised? Other: Newspaper Magazine Radio Website Magazines you regularly purchase from the Newsagent:...
  • Page 51 MEMO...
  • Page 52 MEMO...
  • Page 53 MEMO...
  • Page 54 MEMO...
  • Page 55 MEMO...
  • Page 56 A-7000D-1AU-w Printed in Japan © 2012–2013 Icom Inc. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan Printed on recycled paper with soy ink.

Table of Contents

Save PDF