Icom IC-410PRO Basic Manual
  1. Manuals
  2. Brands
  3. Icom Manuals
  4. Transceiver
  5. IC-410PRO
  6. Basic manual

Icom IC-410PRO Basic Manual

Uhf cb transceiver
Hide thumbs Also See for IC-410PRO:
Table of Contents

Advertisement

Quick Links

See also: Advanced Manual
BASIC MANUAL
UHF CB TRANSCEIVER
i410PRO

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the IC-410PRO and is the answer not in the manual?

Questions and answers

Related Manuals for Icom IC-410PRO

Summary of Contents for Icom IC-410PRO

  • Page 1 BASIC MANUAL UHF CB TRANSCEIVER i410PRO...

  • Page 2: Important

    In Australia, except in an emergency, a CB transmitter shall Icom, Icom Inc. and the Icom logo are registered trademarks of Icom not be operated on UHF emergency channels 5 and 35. Incorporated (Japan) in Japan, the United States, the United Kingdom, v.

  • Page 3: Explicit Definitions

    WARNING! NEVER EXPLICIT DEFINITIONS connect the transceiver to a power source using reverse polarity. This will damage the transceiver. WORD DEFINITION WARNING! NEVER cut the DC power cable between Personal death, serious injury or an RDANGER! the DC plug and fuse holder. If an incorrect connection is explosion may occur.
  • Page 4 MAKE SURE to turn OFF the transceiver power before connecting any supplied/optional equipment. Icom is not responsible for the destruction or damage to the only Icom microphones (supplied or optional). Other Icom transceiver, if the malfunction is because of: manufacturer’s microphones have different pin assignments •...

  • Page 5: Table Of Contents

    SUPPLIED ACCESSORIES TABLE OF CONTENTS Microphone Microphone hanger Microphone IMPORTANT ................i and screw set hanger cable GENERAL INFORMATION ............ i EXPLICIT DEFINITIONS ............ii PRECAUTIONS ..............ii SUPPLIED ACCESSORIES ..........iv 1. PANEL DESCRIPTION ..........1–3 Function name Mounting bracket DC power cable ■...

  • Page 6: Panel Description

    PANEL DESCRIPTION ■ Front panel Function display (p. 3) Speaker q VOLUME CONTROL KNOB r [FUNC] KEY* Adjusts the audio output level. * Different functions may be assigned by your dealer. Push to change between Normal mode and Function w UP/DOWN KEYS [UP]/[DOWN]* mode.
  • Page 7 PANEL DESCRIPTION t [DUP] KEY* u [MONI] KEY* * Different functions may be assigned by your dealer. * Different functions may be assigned by your dealer. Normal mode Normal mode ➥ Push to turn the Monitor (open squelch) function ON ➥...

  • Page 8: Function Display

    PANEL DESCRIPTION ■ Function Display o !0 !1 !2 !3 !4 qw e t yui u PRIORITY CHANNEL ICON Displayed when the Priority channel is set. i LOW POWER ICON Displayed when low output power is selected. o DUPLEX ICON Displayed when a Duplex channel is selected.

  • Page 9: Basic Operation

    BASIC OPERATION ■ Receiving and transmitting Transmit inhibit function NOTE: Transmitting without an antenna may damage the The transceiver will not transmit under the following transceiver. conditions. • The channel is busy. 1. Receiving • The displayed channel is a receive only channel. If “TSQL”...

  • Page 10: Set Mode

    ➥ Hold down [FUNC] for 2 seconds. The transceiver’s Set mode items may differ, depending on 2) Select the “BEEP” menu. the transceiver’s setting. Ask your authorized Icom dealer or ➥ Push [FUNC] until the transceiver administrator for details. “BEEP” menu as shown to the right is displayed.

  • Page 11: Options

    OPTIONS D MICROPHONES D SPEAKERS noise canceling microphone external speaker • HM-211 • SP-35 dtmf microphone • HM-152T External speaker with a 2 meter cable. external speaker Hand microphone with a DTMF keypad. • SP-35L External speaker with a 6 meter cable. DOTHERS acc cable •...

  • Page 12: Troubleshooting

    The Keylock function is ON. Hold down [DUP] for 2 seconds to unlock the keys. (p. 2) Buttons have no effect or do not work The keys may have been Contact your authorized Icom dealer or transceiver administrator as expected reassigned. for details.

  • Page 13: Warranty And Registration

    This Warranty applies to Icom products purchased in Australia. WARRANTY TERMS & CONDITIONS This warranty against defects is given by ICOM (Australia) Pty Ltd 2.2 To the extent permitted by law, our sole liability for breach of a (ABN 88 006 092 575). Our contact details are set out in clause 2.6.

  • Page 14: Warranty And Registration

    Goods improperly installed or used in a manner contrary to the relevant instruction manual; or vi. Goods where the serial number has been removed or made eligible; or vii. Any configurations not sold by ICOM Australia (i.e. Imported U.S or European ICOM versions).
  • Page 16 Thank you for your registration. All of your information will remain strictly confidential. To serve you better, Icom (Australia) Pty. Ltd. will send information about products you may be interested in. If for any reason, you do not want to receive information from Icom (Australia)Pty.

  • Page 17: Index

    INDEX ..................2 Panel description ..............1 Precautions................ii Basic operation ..............4 Priority channel ..............2 Priority scan ................3 Duplex channel ..............3 Duplex mode ................2 Receiving ................4 RX VFO ................5 Explicit definitions ..............ii Selcall ..................3 Front panel ................1 Selcall code ................2 Function display..............3 Selcall Quiet mode ...............3 Function mode ..............1 Set mode ................5 Simplex mode ...............2...
  • Page 18 MEMO...
  • Page 19 MEMO...
  • Page 20 A7256D-1AU-1 Printed in Japan © 2015–2018 Icom Inc. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan Printed on recycled paper with soy ink.

Table of Contents