1. Manuals
  2. Brands
  3. BEC Manuals
  4. Network Router
  5. 8800N
  6. User manual

BEC 8800N User Manual

802.11n vdsl2/ adsl2+ broadband firewall router
Hide thumbs Also See for 8800N:
Table of Contents

Advertisement

Quick Links

See also: Setup Manual
BEC 8800N
802.11n VDSL2/ ADSL2+ Broadband
Firewall Router

User Manual

Last revised on Nov. 2009

Advertisement

Table of Contents
loading

Related Manuals for BEC 8800N

Summary of Contents for BEC 8800N

  • Page 1: User Manual

    BEC 8800N 802.11n VDSL2/ ADSL2+ Broadband Firewall Router User Manual Last revised on Nov. 2009...

  • Page 2: Table Of Contents

    Table of Contents Chapter 1: Introduction ..............1 Introduction to your Router ............1 Features ..................4 Hardware Specifications ............5 Physical Interface ................5 Physical Specifications................5 Operating Environment ............... 5 Chapter 2: Installing the Router ............6 Package Contents ............... 6 Important note for using this router ..........
  • Page 3 Route Table ..................29 ARP Table ..................30 DHCP Table ..................31 System Log ..................32 Configuration ................33 LAN - Local Area Network ..............34 LAN ........................ 34 WAN - Wide Area Network ..............36 Layer2 Interface ....................36 WAN Service ....................40 DSL ......................... 48 System ....................49 Time Zone ......................
  • Page 4 Diagnostics ................84 Diagnostics ..................84 Fault Management ................85 Chapter 5: Troubleshooting ............86 Appendix: Product Support & Contact .......... 87...

  • Page 5: Chapter 1: Introduction

    Chapter 1: Introduction Introduction to your Router Thank you for purchasing 8800N Wireless Broadband Firewall Router. Your new router is an all- in-one unit that combines an VDSL2/ADSL2+/Broadband router and Ethernet network to offer users the flexibility of multiple Internet connections. All this is offered while maintaining high-speed broadband access via VDSL2/ADSL2+.
  • Page 6 Annex M standard supports ADSL2 / 2+ for higher uploads by doubling the upload data rate. The 4-port 10/ 100 Mbps Fast Ethernet Switch incorporated into the BEC 8800N enables users to connect to multiple computers or wired-Ethernet devices easily and enjoy blistering LAN transmission for multimedia applications such as interactive gaming, IPTV video streaming and real-time audio.
  • Page 7 network, Internet. Rich Packet Filtering Not only filters the packet based on IP address, but also based on Port numbers. It will filter packets from the Internet and vice versa, in addition to providing a higher level of security control. Dynamic Host Configuration Protocol (DHCP) Client and Server In the WAN site, the DHCP client can get an IP address from the Internet Service Provider (ISP) automatically.

  • Page 8: Features

    Features • 4-port 10/ 100 Ethernet Switch • Very High-speed Internet Access via VDSL2; Backward Compatible with ADSL2/+ ADSL2/ ADSL • VDSL2 Profiles: 8a/b/c/d, 12a/b, 17a • Quality of Service Control for Traffic Prioritization and Bandwidth Management • SOHO Firewall Security with DoS Prevention and Packet Filtering •...

  • Page 9: Hardware Specifications

    Hardware Specifications Physical Interface • DSL: VDSL/ ADSL port • WAN: Gigabit Ethernet for FTTH and broadband connection • Ethernet: 4-port 10 / 100 auto-crossover (MDI / MDI-X) Switch • Factory default reset button • USB • Power jack • Power switch Physical Specifications •...

  • Page 10: Chapter 2: Installing The Router

    Chapter 2: Installing the Router Package Contents BEC 8800N Router RJ-11 ADSL/telephone cable Ethernet (RJ-45) cable Power adapter Splitter / Microfilter (Optional) Important note for using this router...

  • Page 11: Device Description

    Device Description The Front LEDs Meaning Flash orange when the device is booting Lit green when the system is ready. Power Lit orange when the device fails to boot or when the device is in emergency mode. Lit green when WAN port is being connected to a FTTH or broadband device.

  • Page 12: The Rear Ports

    Connect it with the supplied power adapter. Power Switch Power ON/OFF switch. Connect the USB cable to this port (BEC 8800N only). Press this button for 3~5 seconds to restore the device to its default mode. Note: Be sure that the device is being turned on when Reset press Reset button.

  • Page 13: Cabling

    Cabling One of the most common causes of problem is bad cabling or DSL line(s). Make sure that all connected devices are turned on. On the front panel of your router is a bank of LEDs. Verify that the LAN Link and ADSL line LEDs are lit. If they are not, verify if you are using the proper cables. Make sure that all devices (e.g.

  • Page 14: Chapter 3: Basic Installation

    Chapter 3: Basic Installation The router can be configured through your web browser. A web browser is included as a standard application in the following operating systems: Linux, Mac OS, Windows 98/NT/2000/XP/Me/Vista, etc. The product provides an easy and user-friendly interface for configuration. Please check your PC network components.

  • Page 15: Hardware Connection

    Hardware Connection...

  • Page 16: Network Configuration

    Network Configuration Configuring PC in Windows Vista 1. Go to Start. Click on Network. 2. Then click on Network and Sharing Center at the top bar. 3. When the Network and Sharing Center window pops up, select and click on Manage network connec- tions on the left window column.
  • Page 17 5. Select Internet Protocol Version 4 (TCP/IPv4) then click Properties. 6. In the TCP/IPv4 properties window, select the Obtain an IP address au- tomatically and Obtain DNS Server address automatically radio but- tons. Then click OK to exit the set- ting.

  • Page 18: Configuring Pc In Windows Xp

    Configuring PC in Windows XP 1. Go to Start > Control Panel (in Classic View). In the Control Panel, double-click on Network Connections 2. Double-click Local Area Connection. 3. In the Local Area Connection Status window, click Properties. 4. Select Internet Protocol (TCP/IP) and click Properties.

  • Page 19: Configuring Pc In Windows 2000

    Configuring PC in Windows 2000 1. Go to Start > Settings > Control Panel. In the Control Panel, double-click on Network and Dial-up Connections. 2. Double-click Local Area Connection. 3. In the Local Area Connection Status window click Properties. 4. Select Internet Protocol (TCP/IP) and click Properties.

  • Page 20: Configuring Pc In Windows 95/98/Me

    Configuring PC in Windows 95/98/Me 1. Go to Start > Settings > Control Panel. In the Control Panel, double-click on Network and choose the Configuration tab. 2. Select TCP/IP > NE2000 Compatible, or the name of your Network Interface Card (NIC) in your PC. 3.
  • Page 21 Configuring PC in Windows NT4.0 1. Go to Start > Settings > Control Panel. In the Control Panel, double-click on Network and choose the Protocols tab. 2. Select TCP/IP Protocol and click Prop- erties. 3. Select the Obtain an IP address from a DHCP server radio button and click...

  • Page 22: Factory Default Settings

    Factory Default Settings Before configuring your router, you need to know the following default settings. Web Interface (Username and Password) Username: admin Password: admin The default username and password are “admin” and “admin” respectively. Device LAN IP settings IP Address: 192.168.1.254 Subnet Mask: 255.255.255.0 ISP setting in WAN site PPPoE...

  • Page 23: Information From Your Isp

    Information from your ISP Before configuring this device, you have to check with your ISP (Internet Service Provider) to find out what kind of service is provided such as DHCP (Obtain an IP Address Automatically, Static IP (Fixed IP Address) or PPPoE. Gather the information as illustrated in the following table and keep it for reference.

  • Page 24: Internet Access Configuration

    Internet Access Configuration To configure this device for internet access, you must have IE 5.0 / Netscape 4.5 or above installed on your computer. There is basically one way to configure your device before you are able to connect to the internet: Interface.

  • Page 25: Chapter 4: Configuration

    Chapter 4: Configuration Once you have logged on to your adapter GUI via your web browser, you can begin to configure the device according to your needs. On the configuration homepage, the left navigation pane provides the links to different setup pages. Status (WAN Info / Statistics / Route Table / ARP Table / DHCP Table / System Log) Configuration (LAN / WAN / System / Firewall / QoS / Virtual Server / Advanced) Diagnostics (Diagnostics / Fault Mamagement)

  • Page 26: Status

    Status Device Information Model Name: Displays the model name. Host Name: Provide a name for the router for identification purposes. Host Name lets you change the router name. System Up-Time: Records system up-time. Current time: Set the current time. See the Time Zone section for more information. Hardware Version: Device version.

  • Page 27: Wan Info

    WAN Info The WAN Info screen displays the configured PVC(s) and the status. Interface: Shows connection interfaces. Description: Shows the user defined name of WAN service. Type: Shows the connection type, such as PPPoE, IPoE and so on. VlanMuxld: Shows the status of the VLAN Muxld.

  • Page 28: Statistics

    Statistics These are the items within the Statistics section: LAN, Service, and xDSL. This screen shows interface statistics for LAN of Ethernet interfaces. Interface: Lists connection interfaces. Received/Transmitted Bytes: Rx/TX (receive/transmit) packet in Byte. Received/Transmitted Pkts: Rx/TX (receive/transmit) packets. Received/Transmitted Errs: Rx/TX (receive/transmit) packets that are errors. Received/Transmitted Drops: Rx/TX (receive/transmit) packets that are dropped.

  • Page 29: Wan Service

    WAN Service This screen shows the current statistics for WAN. Interface: Shows connection interfaces. Description: Shows the user defined name of WAN service. Received/Transmitted Bytes: Rx/TX (receive/transmit) packet in Byte. Received/Transmitted Pkts: Rx/TX (receive/transmit) packets. Received/Transmitted Errs: Rx/TX (receive/transmit) packets that are errors. Received/Transmitted Drops: Rx/TX (receive/transmit) packets that are dropped.

  • Page 30: Xtm

    The Statistics-xTM screen displays all the xTM statistics. Port Number: Shows number of the port for xTM. In Octets: Number of received octets over the interface. Out Octets: Number of transmitted octets over the interface. In Packets: Number of received packets over the interface. Out Packets: Number of transmitted packets over the interface.

  • Page 31: Xdsl

    xDSL The Statistics-xDSL screen displays all the xDSL network statistics. DSP Firmware Version: DSP code version. Mode: Modulation protocol, including G.dmt, G.lite, T1.413, ADSL2, ADSL2+ and VDSL2. Traffic Type: Channel type, including ATM or PTM. Status: Shows the status of the DSL link.
  • Page 32 Link Power State: Shows link output power state. Upstream: Upstream rate. Downstream: Downstream rate. Line Coding(Trellis): Trellis On/Off. SNR Margin (0.1 dB): This shows the Signal to Noise Ratio (SNR) margin. Attenuation (0.1 dB): This is estimate of average loop attenuation of signal. Output Power (0.1 dBm): Total upstream output power.

  • Page 33: Route Table

    Route Table The Rout Table provides users with a database in the router that contains current network topology such as current paths for transmitted packets. Both static and dynamic routes are displayed. Destination: Displays the IP address of the destination network. Gateway: Displays the IP address of the gateway that this route uses.

  • Page 34: Arp Table

    ARP Table This table stores mapping information that the device uses to find the Layer 2 Media Access Control (MAC) address that corresponds to the Layer 3 IP address of the device via the Address Resolution Protocol (ARP) feature. IP Address: Shows the IP Address of the device that the MAC address maps to. MAC Address: Shows the MAC address that is corresponded to the IP address of the device it is mapped to.

  • Page 35: Dhcp Table

    DHCP Table This Table lists the DHCP lease information for all IP addresses assigned by the DHCP server in the device. Hostname: The Hostname of internal dhcp client. MAC Address: The MAC Address of internal dhcp client host. IP Address: This is the IP address that is assigned to the host with this MAC address. Expires In: Shows the information provided during registration.

  • Page 36: System Log

    System Log Display system logs accumulated up to the present time. You can trace its historical information with this function. Refresh: Click to update the system log.

  • Page 37: Configuration

    Configuration When you click this item, the column will expand to display the sub-items that will allow you to further configure your GPON router. LAN, WAN, System, Firewall, QoS, Virtual Server and Advanced. The function of each configuration sub-item is described in the following sections.

  • Page 38: Lan - Local Area Network

    LAN - Local Area Network A Local Area Network (LAN) is a shared communication system network where many computers are connected. This type of network is area defined and is usually limited to a confined region within a building or just within the same storey of a building. Ethernet The router supports more than one Ethernet IP addresses in the LAN, and with distinct LAN subnets through which you can access the Internet at the same time.
  • Page 39 multicast packet groups between the host and the router. Default is set to Disable. Check Enable IGMP Snooping check box to activate this function and choose Standard Mode or Blocking Mode. IP Alias This function allows the addition an IP alias to the network interface. This further allows user flexibly to assign a specific function to use this IP.

  • Page 40: Wan - Wide Area Network

    WAN - Wide Area Network A WAN (Wide Area Network) is a computer network that covers a broad geographical area (eg. Internet) that is used to connect LAN and other types of network systems. There are the items within the WAN section: Layer2 Interface, WAN Service...
  • Page 41 ATM Interface (ADSL) Click Add to go to ATM PVC Configuration screen. VPI (0~255) / VCI (32~65535): Enter the VPI/VCI values provided by your ISP. DSL Latency: Check Path0 or Path1 for DSL latency. DSL Link Type: Select EoA (which is for PPPoE, IPoE and Bridge), PPPoA, or IPoA. Select the one provided by your ISP.
  • Page 42 Sustainable Cell Rate (cells/s): Specifies the upstream sustainable cell rate, in cells per second, used for traffic shaping. Maximum Burst Size (cells/s): Specifies the upstream maximum burst size in cells. Connection Mode: Choose a appropriate connection mode. Enable Quality Of Service: Check to activate packet level QoS for this PTM interface. To assign priorities for the applications, please use Advanced Setup>Quality of Service.
  • Page 43 ETH Interface (EWAN) Click Add to go to ETH WAN Configuration screen. ETH port: Select the port for ETH WAN connection from the listbox. Connection Mode: Choose a appropriate connection mode. Click Apply/Save to save the changes or Back to return to ETH WAN Interface table.

  • Page 44: Wan Service

    WAN Service Note: You have to set an interface at least previously. (Please refer to PTM Interface, ATM Interface and ETH Interface sections. ETH and PTM/ATM service can not coexist.) If the WAN interface has not set, a page will display as below and you are not allowd to create a WAN connection.
  • Page 45 PPP over Ethernet PPPoE (PPP over Ethernet) provides access control in a manner similar to dial-up services using PPP. Select WAN service type: Click PPP over Ethernet (PPPoE) radio button. Enter Service Description: You are allowed to enter the user defined name for this service.
  • Page 46 PPPoE Service Name: This item is for identification purposes. If it is required, your ISP will provide you the necessary information. Maximum input is 32 alphanumeric characters. Authentication Method: Default is AUTO. Please consult your ISP on whether to use PAP, CHAP or MSCHAP.
  • Page 47 WAN Interface selected: This field is available when DNS Type is "Obtain DNS info from a WAN interface". Select a WAN interface for this device to obtain the DNS information. Primary DNS server/Secondary DNS server: These fields are available when DNS Type is "Use the following Static DNS IP address".
  • Page 48 IP over Ethernet Select WAN service type: Click IP over Ethernet radio button. Enter Service Description: You are allowed to enter the user defined name for this service. Click Next to go to next step. IPv4 Protocol: Select the appropriate protocol. There are 2 options: Obtain an IP Address Automatically and Fixed IP Address.
  • Page 49 selected in the IPv4 Protocol field, default value 0.0.0.0 will display in this field. WAN gateway IP Address: Enter your gateway IP address to the device provided by your ISP. If Fixed IP Address is selected in the IPv4 Protocol field, default value 0.0.0.0 will display in this field. Click Next to go to next step.
  • Page 50 DNS Type: Select the appropriate DNS type. WAN Interface selected: This field is available when DNS Type is "Obtain DNS info from a WAN interface". Select a WAN interface for this device to obtain the DNS information. Primary DNS server/Secondary DNS server: These fields are available when DNS Type is "Use the following Static DNS IP address".
  • Page 51 Bridging Select WAN service type: Click Bridging radio button. Enter Service Description: You are allowed to enter the user defined name for this service. Click Next to go to next step. This page lists a summary of previous steps. Make sure that the settings are the same as those provided by your ISP and then click Apply/Save to complete the configuration process.

  • Page 52: Dsl

    This screen allows you to set DSL parameters. DSL knowledge is required to configure these settings. Contact your ISP to make sure that these parameters are correct. Modulation: There are 8 modes “G.Dmt”, “G.lite”, “T1.413”, “ADSL2”, “AnnexL”, ”ADSL2+”, “AnnexM”, and “VDSL2” that user can select for this connection. G.Dmt/G.lite Enabled: Tick the G.Dmt/G.lite check box if you want the system to use either G.Dmt or G.lite mode.

  • Page 53: System

    System There are 5 items within the System section: Time Zone, Firmware Upgrade, Backup/Restore, Restart User Management. Time Zone Enable or disable the time zone function. If you disable time zone, the other blanks are unavailable. The router does not have a real time clock on board; instead, it uses the Simple Network Time Protocol (SNTP) to get the most current time from an SNTP server outside your network.

  • Page 54: Firmware Upgrade

    Firmware Upgrade Your router’s firmware is the software that enables it to operate and provides all its functionality. Think of your router as a dedicated computer, and the firmware as the software that runs in your router. Thus, by upgrading the newly improved version of the firmware allows you the advantage to use newly integrated features.

  • Page 55: Backup / Restore

    Backup / Restore These functions allow you to save a backup of the current configuration of your router to a defined location on your PC, or to restore a previously saved configuration. This is useful if you wish to experiment with different settings, knowing that you have a backup in hand in case any mistakes occur.

  • Page 56: Restart

    Restart There are 2 options for you to choose from before restarting the your device. You can either choose to restart your device to restore it to the Factory Default Settings or to restart the device with your current settings applied. Restarting your device to Factory Default Setting will be useful especially after you have accidentally changed your settings that may result in undesirable outcome.

  • Page 57: User Management

    User Management In order to prevent unauthorized access to your router configuration interface, it requires all users to login with a username and password. Therefore only system administrator can access the system. It is highly recommended that you change your password upon receiving your router. The default password is “admin”.

  • Page 58: Firewall

    Firewall Listed are the items under the Firewall section: Filtering, MAC Filtering Parental Control. IP Filtering Packet filtering enables you to configure your router to block specific internal / external users (IP address) from Internet access, or disable specific service requests (Port number) to / from the Internet.
  • Page 59 the listbox. Select TCP if you wish to search for the connection-based application service on the remote server using the port number. Or select UDP if you want to search for the connectionless application service on the remote server using the port number. Source IP address: This is an Address-Filter used to allow or block traffic from particular IP address(es).
  • Page 60 Incoming All incoming IP traffic from the WAN is blocked by default when the firewall is enabled. However, some IP traffic can be accepted by setting up filters. Click Add to enter Add IP Filter -- Incoming screen to add a filter rule for incoming IP traffic. Filter Name: User defined description for entry identification.
  • Page 61 Destination IP address: This is an Address-Filter used to allow or block traffic to particular IP address(es). Enter the IP range that you want to filter. If only the first IP block is filled, it means only that IP entered will be targeted. If you leave both IP blocks empty, it means any IP address. Destination Subnet Mask: Type the subnet mask associated with the Destination IP address.

  • Page 62: Mac Filtering

    MAC Filtering A MAC (Media Access Control) address is the unique network hardware identifier for each PC on your network’s interface (i.e. its Network Interface Card or Ethernet card). Using your router’s MAC Address Filter function, you can configure the network to block specific machines from accessing your LAN.
  • Page 63 You should specify at least one condition below to set a MAC filter profile. If multiple conditions are specified, all of them take effect. Protocol Type: Select which protocol this filter will be applied to from the drop-down menu. Destination MAC Address: Enter the destination MAC address this filter will be applied to. The format of MAC address could be: xx:xx:xx:xx:xx:xx or xx-xx-xx-xx-xx-xx.

  • Page 64: Qos - Quality Of Service

    QoS - Quality of Service QoS helps you to control the data upload traffic of each application from LAN (Ethernet) to WAN (Internet). It facilitates you the features to control the quality and speed of throughput for each application when the system is running with full upstream load. QoS Enable: Check to activate QoS function and the following field will be available.

  • Page 65: Queue Config

    Queue Config Queue Config allows you to configurate a QoS queue entry and assign it to a specific network interface. Each queue entry set here will be used by the classfier to place ingress packets appropriately. Click Add to create the queue. Name: Enter a name for this QoS item.
  • Page 66 Enable: To disable the item, please uncheck Enable check box then click Enable button. Remove: To delete the QoS rule from the table, check Remove checkbox then click Remove button to delete the selected item.

  • Page 67: Qos Classification

    QoS Classification This screen displays a packet QoS summary table and allows user to add or remove a QoS classification class. This is the main place to configure the classification, marking and queuing rules. Click Add to configure network traffic classes.
  • Page 68 Parameters Traffic Class Name: Assign a name for this class to uniquely identify the other(s) among multiple classes. Rule Order: Select the priority for this class rule. Rule Status: Select Enable to activate this class rule. Specify Classification Criteria Enter or select appropriate parameters on the following fields. A blank criterion indicates it is not used for classification.

  • Page 69: Virtual Server

    Virtual Server Virtual Server allows you to direct incoming traffic from WAN side (identified by Protocol and External port) to the Internal server with private IP address on the LAN side. The Internal port is required only if the external port needs to be converted to a different port number used by the server on the LAN side.

  • Page 70: Port Mapping

    Port Mapping Click Add to enter Port Mapping configuration screen. Parameters Use Interface: Select a interface which you want from the frop-down menu. Service Name Choose the service you need for this server. If you choose Select a Service, select an application from the listbox.
  • Page 71 External Port Start / External Port End: Enter the public port number & range you wish to configure. Protocol: In addition to specifying the port number used, you also need to specify the protocol used. The protocol is determined by a particular application. Most applications use TCP or UDP, however you may also specify other protocols using the drop-down Protocol menu.

  • Page 72: Dmz Host

    DMZ Host The DMZ Host is a local computer exposed to the Internet. When setting a particular internal IP address as the DMZ Host, all incoming packets that do not use a port number which is already used by any other Virtual Server entries will first be checked by the Firewall and NAT algorithms before it is passed to the DMZ host.

  • Page 73: Advanced

    Advanced Configuration options within the Advanced section are for users who wish to take advantage of the more advanced features of the router. Users who do not understand the features should not attempt to reconfigure their router, unless advised to do so by support staff. Here are the items within the Advanced section: Routing, DNS, Interface Grouping,...

  • Page 74: Static Route

    Static Route With static route feature, you are equipped with the capability to control the routing of the all the traffic across your network. With each routing rule created, you can specifically assign the destination where the traffic will be routed to. Destination: Enter the destination IP where the traffic is to be forwarded.
  • Page 75 Interface: Displays the interface for the RIP rule. Version: Select the desired RIP version for this interface. Gateway: Select the desired RIP operation for this interface. Enabled: Check Enabled check box for the interface. Click Apply/Save to confirm the settings.

  • Page 76: Dns

    DNS Server On the Internet, Domain Name System (DNS) servers are used to translate a hostname or a domain name to its corresponding binary identifier. If you check "Obtain DNS info from a WAN interface", this router will accept the first received DNS assignment from one of the WAN interface during the connection establishment.

  • Page 77: Dynamic Dns

    Dynamic DNS The Dynamic DNS function lets you alias a dynamic IP address to a static hostname, so if your ISP does not assign you a static IP address you can still use a domain name. This is especially useful when hosting servers via your ADSL connection, so that anyone wishing to connect to you may use your domain name, rather than the dynamic IP address which is assigned to you by ISP.

  • Page 78: Interface Grouping

    Interface Grouping This function allows you to set new interfce group. Click Add to create a new interface grouping. Group Name: Enter the name that you want this interface group to have. WAN Interface used in the grouping: Select appropriate WAN interface. Grouped LAN Interfaces: Displays the list of selected ethernet ports in this group.
  • Page 79 Automatically Add Clients With the following DHCP Vendor IDs: Enter the IDs in the fields. Click on Save/Apply button to finish the configuration and you will be returned to Interface Grouping table. Remove: To delete the Interface Grouping from the table, check Remove checkbox then click Remove button to delete the selected item.

  • Page 80: Device Management

    Device Management The Device Management advanced configuration settings allow you to control your router’s security options and device monitoring features. UPnP offers peer-to-peer network connectivity for PCs and other network devices, along with the feature to control data transfer between devices. UPnP offers many advantages for users running NAT routers through UPnP NAT Traversal, and on supported systems.
  • Page 81 Installing UPnP in Windows Example Follow the steps below to install the UPnP in Windows Me. Step 1: Click Start and Control Panel. Double-click Add/Remove Programs. Step 2: Click on the Windows Setup tab and select Communication in the Components selection box.
  • Page 82 Step 4: Click OK to go back to the Add/Remove Programs Properties window. Click Next. Step 5: Restart the computer when prompted. Follow the steps below to install the UPnP in Windows XP. Step 1: Click Start and Control Panel. Step 2: Double-click Network Connections.
  • Page 83 Auto-discover Your UPnP-enabled Network Device Step 1: Click start and Control Panel. Double-click Network Connections. An icon displays under Internet Gateway. Step 2: Right-click the icon and select Properties. Step 3: In the Internet Connection Properties window, click Settings to see the port mappings that were automatically created.
  • Page 84 Step 4: You may edit or delete the port mappings or click Add to manually add port mappings. Step 5: Select Show icon in notification area when connected option and click OK. An icon displays in the system tray. Step 6: Double-click on the icon to display your current Internet connection status.
  • Page 85 Step 3: Select My Network Places under Other Places. Step 4: An icon describing each UPnP-enabled device shows under Local Network. Step 5: Right-click on the icon of your BEC 8800N and select Invoke. The web configuration login screen displays.

  • Page 86: System Log Server

    System Log Server This screen allows you to view the system events log or to configure the system log options. Send Log To Remote Server: By default, it is disabled. To enable it, tick Enable to activate system log. Log Server IP Address: Enter the server IP address. Log Server UDP Port: Enter the server UDP port.

  • Page 87: Tr-069 Client

    TR-069 Client Please contact your ISP for the information of TR069. Inform: You can enable or disable the periodic inform feature. Inform Interval: Enter the length of the periodic inform interval (unit: seconds). ACS URL: Enter the ACS URL address. ACS Username: Enter the ACS server login name.

  • Page 88: Diagnostics

    Diagnostics Here are 2 items within this section: Diagnostics Fault Management. Diagnostics This page allows users to test the Ethernet port connection, DSL port connection, and connection to the Internet Service Provider. If a test displays a FAIL status, click "Test" again or "Test With OAM F4"...

  • Page 89: Fault Management

    Fault Management IEEE 802.1ag Ethernet Connectivity Fault Management protocols comprise three protocols: continuity check, link trace and loopback protocols that work together to help administrators debug Ethernet networks. On this screen, you can configure 802.1ag CFM and use this function.

  • Page 90: Chapter 5: Troubleshooting

    If your router is not functioning properly, please refer to the suggested solutions provided in this chapter. If your problems persist or the suggested solutions do not meet your needs, please kindly contact your service provider or BEC for support. Problem...

  • Page 91: Appendix: Product Support & Contact

    Appendix: Product Support & Contact If you come across any problems please contact the dealer from where you purchased your prod- uct. Contact BEC http://www.bectechnologies.net MAC OS is a registered Trademark of Apple Computer, Inc. Windows 98, Windows NT, Windows 2000, Windows Me, Windows XP and Windows Vista are...

Table of Contents