3 way dual 12" large format loudspeaker for high performance installation applications, 2 way down-firing dual concentric mid-high loudspeaker for high performance installation applications, 2 way dual concentric mid-high large format loudspeaker for high (57 pages)
15/12 inch power dual full range loudspeaker with q-centric waveguide/low frequency driver for portable and installation applications.
12/8/6/5 inch dual concentric full range loudspeaker with low frequency driver for
portable and installation application (9 pages)
Passive column array loudspeaker with 15/30 drivers and fast dispersion, control for installation applications/en 54-24 certified, passive column array loudspeaker with 7 full range drivers and fast dispersion, control for installation applications en 54- (12 pages)
Single or Bi-Amp mode, in conjunction with a suitable digital signal processor (DSP). The VQ MB duplicates the low frequency performance of the VQ 60 & VQ 100 full range loudspeakers, it is intended for use as a flown or ground stacked, high power low/mid frequency module used in conjunction with full range or mid/high systems in the VQ series.
2 UNPACKING Every Tannoy VQ product is carefully tested and inspected before being packaged and leaving the factory. After unpacking your loudspeaker, please inspect for any exterior physical damage, and save the carton and any relevant packaging materials in case the loudspeaker again requires packing and shipping. In the event that damage has been sustained in transit notify your dealer immediately.
Page 5
The VQ 60, VQ 100 and VQ DF are fitted with 4-pole Neutrik Speakon connectors and barrier strip for fixed installations. Speakon Connections - Speakon has the following advantages over EP and XLR type connectors: All terminations are solderless; this makes life easier at the time of installation or when field servicing is required.
Page 6
The barrier strip accommodates bare wire, tinned leads or spade connectors. The barrier strips are specifically designed for utilization in fixed/permanent installations. The VQ 60 and VQ 100 are configured for Bi-amp operation; by removing the 4 link wires between the two barrier strips on the termination panel tri-amp operation is possible.
4 POLARITY CHECKING It is most important to check the polarity of the wiring before the speaker system is flown. A simple method of doing this without a pulse based polarity checker for LF units is as follows: Connect two wires to the +ve and -ve terminals of a PP3 battery.
In its basic configuration the Tannoy VNET SC1 is a powerful 2 in 6 out digital system controller provides multiple X-Over, EQ, Delay and Limiting options. Using DSP-based digital crossovers with 96kHz sampling rates, this versatile controller will enable simple configuration and optimization of loudspeakers in terms of speaker management and room EQ functionality.
Again, the placement of the units has a great bearing on the resultant parameters you use. For instance, if a VQ 60 is used next to a boundary it's low frequency roll off characteristic will change, so a different slope may be required.
WARNING: Do not under any circumstances use a loudspeaker's handles to support the weight of the loudspeaker except for their intended use: hand carrying. The handles are not rated to support the load of the loudspeaker for temporary or permanent installation. The VQ range of loudspeakers is intended to be suspended or ground-stacked.
7.2 VQ FLYING BRACKET (SINGLE POINT HANG FLYING BRACKET) For safe, flexible and simple flying, the VQ Flying bracket is designed to suspend the VQ cabinet from a single pivot point. This allows precise adjustment of aiming angles with the cabinet in situ. The flown VQ loudspeaker must be provided with an independent, correctly rated and securely attached secondary safety –...
Page 19
Fixing of hanging points in a roof should always be carried out by a professional rigger and in accordance with the local rules of the venue. A maximum of VQ 60 + VQ MB + VQ DF (350lbs, 160kg) can be flown from a single threaded rod. This combination carries a safety factor of 8:1. (See fig. 3) (fig.
7.3 VQ LINK PLATE The VQ link plate is used to join a VQ DF or VQ MB to a VQ 60 or VQ 100 cabinet. Three link plates are used to connect each cabinet. The Link plates are supplied as standard with each VQ DF and VQ MB.
Two VQ 60 s can be arrayed to produce a well defined horizontal coverage angle of 120 degrees. The VQ array plate is designed to optimally array two VQ 60 cabinets. To fit the plate, set the boxes on the ground with the rear edge of the cabinets touching.
Page 22
11.0° 18.8° 26.0° 32.4° 38.0° 0.2° 8.9° 17.3° 25.0° 31.8° 37.8° VQ 60 & VQ DF VQ 100 & VQ DF A B C D E F A B C D E F -4.9° 1.4° 7.6° 13.6° 19.4° 24.7° -4.9°...
7.7 CENTRE OF GRAVITY LOCATIONS Centre of Gravity Product Number Product Name Y (vertically) Z (horizontally) 8001 4800 VQ-60 444.4mm (17.5in) 302.6 (11.91in) 8001 4810 VQ-MB 216.6mm (8.53in) 311.2 (12.25in) 8001 4820 VQ-100 481.3 (18.95in) 326.9 (12.87in) 8001 4830 VQ-DF 188.8 (7.43in) 266.9 (10.51in) 8001 4840...
Page 24
Claims will not be considered is the serial number has been altered or removed. Work under warranty should only be carried out by a Tannoy dealer or service agent. This warranty in no way affects your statutory rights. For further information please contact your dealer or distributor in your country.
SERVICE PARTS AND ACCESSORIES VQ 60 VQ 100 DRIVER KIT DRIVER KIT DRIVER KIT DRIVER KIT TYPE 1220 TYPE 1221 TYPE 1220 TYPE 1221 7900 1063 7900 1066 7900 1063 7900 1066 HF DIAPHRAGM HF DIAPHRAGM HF DIAPHRAGM HF DIAPHRAGM...
Page 26
Full independent verification of published specifications carried out by NWAA Labs, LF @ 4 Ohms 1000W (63.3V) 2000W California can also be obtained from the downloads section of www.tannoy.com MF @ 8 Ohms 200W (40V) 400W Tannoy operates a policy of continuous research and development. The introduction...
Page 27
Full independent verification of published specifications carried out by NWAA Labs, Mid Frequency 134dB 140dB California can also be obtained from the downloads section of www.tannoy.com High Frequency 133dB 139dB Tannoy operates a policy of continuous research and development. The introduction...
Page 28
400W Full independent verification of published specifications carried out by NWAA Labs, California can also be obtained from the downloads section of www.tannoy.com Tannoy operates a policy of continuous research and development. The introduction of new materials or manufacturing methods will always equal or exceed the published specifications, which Tannoy reserves the right to alter without prior notice.
Page 29
105dB (2.0V @ 4 Ohms) Full independent verification of published specifications carried out by NWAA Labs, California can also be obtained from the downloads section of www.tannoy.com Driver Complement 2 x 300mm (12.00”) Low Tannoy operates a policy of continuous research and development. The introduction...
DECLARATION OF CONFORMITY The following apparatus is manufactured in the United Kingdom by Tannoy Ltd of Rosehall Industrial estate, Coatbridge, Scotland, ML5 4TF and conform(s) to the protection requirements of the European Electromagnetic Compatibility Standards and Directives relevant to professional apparatus used in commercial light industrial environments. The apparatus is designed and constructed...