Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Tannoy V15
Summary of Contents for Tannoy V15
- Page 1 User Manual...
-
Page 3: Table Of Contents
CONTENTS Introduction Unpacking Connectors/Cabling Polarity Checking Amplification & Power Handling Crossovers Equalisation Arraying Dimensions Performance Data Technical Specifications Rigging & Suspension 12.1 General Safety Advice 12.2 Secur – ET VMY Yoke bracket 12.3 Secur – ET VMB Wall mounting Bracket 12.4 Secur –... -
Page 4: Introduction
Like all Tannoy Dual Concentric loudspeakers the Tannoy V15 exhibits true constant directivity, providing an even frequency response over the entire area of coverage. The output capability makes the Tannoy V15 suitable for much larger audience sizes or venues requiring very high SPL’s, such as nightclubs. -
Page 5: Polarity Checking
Cable choice consists mainly of selecting the correct cross sectional area in relation to the cable length and the load impedance. A small cross sectional area would increase the cables series resistance, inducing power loss and response variations (damping factor). Connectors should be wired with a minimum of 2.5 sq. -
Page 6: Amplification & Power Handling
The V15 is supplied as standard for passive operation via the internal crossover network. If higher peak outputs and additional low frequency output is required then the V15 can be used in conjunction with the Tannoy TX2 controller/crossover which provides high pass filtering and a degree of parametric equalisation, as well as a fixed crossover point for use with sub-bass loudspeakers (See the TX2 user manual for further information). -
Page 7: Arraying
10deg 50deg As shown in the above diagram, one of the V15 cabinets is inverted to allow the optimum splay angle to be achieved. The grill can be simply removed from this cabinet and be replaced in the correct orientation. The grill is held in position by the two fixing screws on the top and bottom... -
Page 8: Dimensions
9. Dimensions 30deg 50deg 200.0 370.0 180.0 420.0 180.0 200.0 370.0 450.0 200.0 225.0 590.0 510.0 180.0 295.0 205.0 40.0... -
Page 9: Performance Data
Unprocessed Anechoic Frequency Response, 1 watt @ 1 metre Impedance A comprehensive range of measurements including off axis frequency response curves, octave & third octave polar diagrams (single & two cabinet arrays) and beamwidth plots as well as Ease data can be downloaded http://www.tannoy.com/ from... -
Page 10: Technical Specifications
(3) Unweighted pink noise input, measured at 1m in an anechoic chamber All Tannoy V Series products can be used with the Tannoy TDX2 Digital Controller for optimum system performance and when being used with various sub bass systems. Please visit our website at www.tannoy.com... -
Page 11: Rigging & Suspension
Tannoy Professional products, or any other devices. Using Tannoy Professional hardware for any purpose other than that indicated in this guide is considered to be improper use. Such use can be very dangerous as overloading, modifying, assembling in anyway other than that clearly stated in the manual, or damaging Tannoy Professional hardware will compromise safety. -
Page 12: Secur - Et Vmy Yoke Bracket
V15 in both orientations to allow easy adjustment for optimum coverage. The vertical distance between the apex of the VMY and the top of the Tannoy V15 loudspeaker can be adjusted by connecting to varying mounting points on the bracket allowing varying degrees of vertical rotation. - Page 13 Use the table of parts along with the assembly drawing (Figure 3.) to assemble the VMY. Figure 4 shows the VMY assembled. Fig 3. Number on Assembly View (Fig 3.) Description Quantity Hanging Bracket Cross Member Pivot Stud M10 Plain Washer M8 Spring Washer M10 Spring Washer M10 x 30mm Screw...
-
Page 14: Secur - Et Vmb Wall Mounting Bracket
VMY, available in both black FIG 1. and white finishes, allowing the user secure the Tannoy V15 loudspeaker in either portrait or landscape orientations to a wall. The Tannoy V15 loudspeaker is attached to the bracket using the accessories supplied. -
Page 15: Secur - Et Veb Eyebolts
Only use the outer fixing points on the top and sides of the V15 cabinet for fixing eyebolts. The inner two fixing points on each side of the cabinet are for dedicated bracketry (VMY) only. -
Page 16: Secur - Et Vth Pole Mount
The Tannoy V15 loudspeaker is fitted as standard with a blanking plate on the base of the cabinet. However, should you ever wish to mount the V15 onto a standard 35mm pole mount this blanking plate can be quickly and easily removed and replaced by a VTH pole mount. -
Page 17: System Configuration & Oem Controllers
13. System Configuration & OEM Controllers 13.1 Passive or Biamp? The V15 is supplied as standard for passive operation via the internal crossover network and is connected as shown in Figure 1. To reconfigure for Biamp operation simply follow the wiring schematic as shown in Figure 2. -
Page 18: Passive System Parameters (Optional)
V15 has been designed to need no external equalisation to overcome system limitations. If the V15 is to be used alone with additional bass enhancement required and have the frequency response limits tighter than +/- 3dB as stated in section 11, then apply the parameters in... -
Page 19: Biamp System Parameters
Q / Bandwidth â â Note : When using the V15 with subs, set HPF on LF section @ 80 – 100Hz (24dB/oct LR) and omit PEQ1 (on LF only) PEQ 1 (on LF only) may also be omitted when using the V15 as a floor monitor. -
Page 20: V12 Recommended Service Parts & Accessories
Work under warranty should only be carried out by a Tannoy Professional dealer or service agent. This warranty in no way affects your statutory rights. For further information please contact your dealer or distributor in your country. If you cannot locate your distributor please contact Customer Services, Tannoy Ltd at the address given below. -
Page 21: Declaration Of Conformity
16. Declaration of Conformity The following apparatus is/are manufactured in the United Kingdom by Tannoy Ltd of Rosehall Industrial estate, Coatbridge, Scotland, ML5 4TF and conform(s) to the protection requirements of the European Electromagnetic Compatibility Standards and Directives relevant to Domestic Electrical Equipment. The apparatus is designed... - Page 22 Strathclyde, ML5 4TF, SCOTLAND Telephone: +44 (0)1236 420199 Fax: +44 (0)1236 428230 Tannoy North America Inc, Suite 1. 335 Gage Avenue, Kitchener, Ontario, CANADA, N2M 5E1 Telephone: (519) 745 1158 Fax: (519) 745 2364 Tannoy Nederland BV, Anthonetta Kuijlstraat 19, 3066 GS, Rotterdam THE NETHERLANDS Telephone: (010) 2860554 Fax: (010) 2860431 Issue 1.0 Part No.