Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Tannoy V12
Summary of Contents for Tannoy V12
- Page 1 User Manual...
-
Page 3: Table Of Contents
12.4 Secur – ET VEB Eyebolts 12.5 Secur – ET VTH Pole mount 12.6 Secur – ET VCS Ceiling Saddle 12.7 Secur – ET VPC Pole Clamp System Configuration & OEM Controllers V12 Recommended Service Parts & Accessories Warranty Declaration of Conformity... -
Page 4: Introduction
The V12 comprises one 12 inch Dual Concentric driver in which the low frequency (LF) and high frequency (HF) sources are coincidentally aligned to a point source, resulting in a smooth uniform frequency response over a wide area of coverage either as a portable stand alone system or in a multi-cabinet array. -
Page 5: Polarity Checking
Cable choice consists mainly of selecting the correct cross sectional area in relation to the cable length and the load impedance. A small cross sectional area would increase the cables series resistance, inducing power loss and response variations (damping factor). Connectors should be wired with a minimum of 2.5 sq. -
Page 6: Amplification & Power Handling
The V12 is supplied as standard for passive operation via the internal crossover network. If higher peak outputs and additional low frequency output is required then the V12 can be used in conjunction with the Tannoy TX2 controller/crossover which provides high pass filtering and a degree of parametric equalisation, as well as a fixed crossover point for use with sub-bass loudspeakers (See the TX2 user manual for further information). -
Page 7: Arraying
60deg As shown in the above diagram, one of the V12 cabinets is inverted to allow the optimum splay angle to be achieved. The grill can be simply removed from this cabinet and be replaced in the correct orientation. -
Page 8: Rigging & Suspension
Tannoy Professional products, or any other devices. Using Tannoy Professional hardware for any purpose other than that indicated in this guide is considered to be improper use. Such use can be very dangerous as overloading, modifying, assembling in anyway other than that clearly stated in the manual, or damaging Tannoy Professional hardware will compromise safety. -
Page 9: Secur - Et Vmy Yoke Bracket
V12 in both orientations to allow easy adjustment for optimum coverage. The vertical distance between the apex of the VMY and the top of the Tannoy V12 loudspeaker can be adjusted by connecting to varying mounting points on the bracket allowing varying degrees of vertical rotation. - Page 10 Use the table of parts along with the assembly drawing (Figure 3.) to assemble the VMY. Figure 4 shows the VMY assembled. Fig 3. Number on Assembly View (Fig 3.) Description Quantity Hanging Bracket Cross Member Pivot Stud M10 Plain Washer M8 Spring Washer M10 Spring Washer M10 x 30mm Screw...
-
Page 11: Secur - Et Vmb Wall Mounting Bracket
VMY, available in both black FIG 1. and white finishes, allowing the user secure the Tannoy V12 loudspeaker in either portrait or landscape orientations to a wall. The Tannoy V12 loudspeaker is attached to the bracket using the accessories supplied. -
Page 12: Secur - Et Veb Eyebolts
Only use the outer fixing points on the top and sides of the V12 cabinet for fixing eyebolts. The inner two fixing points on each side of the cabinet are for dedicated bracketry (VMY) only. -
Page 13: Secur - Et Vth Pole Mount
The Tannoy V12 loudspeaker is fitted as standard with a blanking plate on the base of the cabinet. However, should you ever wish to mount the V12 onto a standard 35mm pole mount this blanking plate can be quickly and easily removed and replaced by a VTH pole mount. -
Page 14: System Configuration & Oem Controllers
TX2 & TDX2 as part of a large scale integrated system. The V12 has been designed to need no external equalisation to overcome system limitations. If the V12 is to be used alone with additional bass enhancement required and have the frequency response limits... -
Page 15: V12 Recommended Service Parts & Accessories
Work under warranty should only be carried out by a Tannoy Professional dealer or service agent. This warranty in no way affects your statutory rights. For further information please contact your dealer or distributor in your country. If you cannot locate your distributor please contact Customer Services, Tannoy Ltd at the address given below. -
Page 16: Declaration Of Conformity
16. Declaration of Conformity The following apparatus is/are manufactured in the United Kingdom by Tannoy Ltd of Rosehall Industrial estate, Coatbridge, Scotland, ML5 4TF and conform(s) to the protection requirements of the European Electromagnetic Compatibility Standards and Directives relevant to Domestic Electrical Equipment. The apparatus is designed... - Page 17 Strathclyde, ML5 4TF, SCOTLAND Telephone: +44 (0)1236 420199 Fax: +44 (0)1236 428230 Tannoy North America Inc, Suite 1. 335 Gage Avenue, Kitchener, Ontario, CANADA, N2M 5E1 Telephone: (519) 745 1158 Fax: (519) 745 2364 Tannoy Nederland BV, Anthonetta Kuijlstraat 19, 3066 GS, Rotterdam THE NETHERLANDS Telephone: (010) 2860554 Fax: (010) 2860431 Issue 1.0 Part No.