Log Set Installation - HearthStone 8120 Owner's Manual And Installation Manual

Hearthstone Quality Home Heating Products, Inc.
carbon monoxide. If the panel set does not fit into
the firebox exactly as outlined, contact your dealer
for assistance.
P P
ANEL LACEMENT
CAUTION: Fragile! Handle panel set with care.
Always wear gloves and safety goggles while
handling.
1) Remove the cast top of the stove by lifting it
straight up and off the unit.
2) Remove front façade by lifting it up and off the
front.
3) Using a flat tip screwdriver, lift and rotate up the
two retaining clips on the top of the firebox and
remove the glass front.
4) Carefully remove the bubble wrapped panels
from the firebox, unwrap and inspect for
damage or missing parts. Contact your dealer if
necessary.
5) The panels are very fragile – do not force them
into position!
6) Insert the rear panel into the firebox, right edge
first, rotate panel flat against rear wall and
lower into place behind the pilot assembly.
Center the panel and push it back as far as
possible.
7) Insert the right panel into the firebox, partially
insert the long edge into the groove inside the
right side of the firebox opening, raise the panel
about two inches so it will clear the pilot
assembly and rotate it into place against the
side wall while seating it in the groove. The
panel will not clear the rear panel if it is not
inserted fully into the groove. Slide the panel
down onto its supporting flange.
8) Insert the upper panel into the firebox and place
its lower edge on top of the rear panel. The
right side panel will now hold the top panel up in
position in the firebox.
9) Insert the left panel into the firebox, place it on
the support flange and carefully insert the long
edge partially into the groove inside the left side
of the firebox. Rotate the panel into place while
seating it in the groove.
10) Ensure the side and rear panels are firmly
seated, and then move the top panel into its
final position. There should be no large gaps
between the upper and lower panels.
R P
EMOVAL OF
CAUTION: The panels retain heat and can be very
hot! Allow 2 to 3 hours after pilot light is turned off
before handling.
To remove the panel set, follow the Installation of
Panel Set instructions in the reverse order.
L S I
OG ET NSTALLATION
CAUTION: Fragile!
Always wear gloves and safety goggles while
handling the log set.
Only the Log set supplied with the Tudor should be
placed in the firebox. Do not place any other logs,
wood logs, or other materials in the firebox. If the
log set is damaged or broken contact your dealer for
replacement. It must be replaced with the same
approved replacement parts.
affect the combustion quality and safety of the
heater. The Log set will last a long time, however,
they will break if subjected to rough or improper
handling. Exact positioning of the log set is required
in order to obtain a pleasing flame pattern and
efficient combustion. Incorrect log placement may
cause carbon build-up; excess thermal stress on the
log set and stove parts, reduced efficiency, and high
levels of carbon monoxide. If the log set does not fit
into the firebox exactly as outlined, contact your
dealer for assistance.
L S P
OG ET LACEMENT
1) If not already so, open the doors on the front
of the unit, and remove the front cast and glass
assembly. To remove the front, grasp both
sides of the front cast facade, and lift upward
and then outward. Set the front aside taking
care not to chip or scratch the enamel. Next,
locate the two rotating clips above the glass.
Rotate the clips out of the "locked" position and
tilt the top of the glass outward. Lift the entire
glass assembly up and out.
2) Gently take the logs out of the accessory box
and remove the bubble wrap from the log set.
Be careful not to damage the log set when
unpacking. There are two logs, a Front and a
Rear.
3) Gently place the TEK burner in the firebox.
Take care to avoid damaging the left side
19
TUDOR 8120 Gas-Fired Direct-Vent
S
ANEL ET
Handle log set with care.
These components