8.0 TRoUblEsHooTInG 9.0 TECHnICAl sPECIfICATIons sTRonG declares that this item complies with the basic requirements and other relevant regulations of directives 2004/108/EC and 73/23/EC, RoHs 2002/95/EC Subject to alterations. In consequence of continuous research and development technical specifications, design and appearance of products may change.
PART 1 • English 1.0 InTRoDUCTIon 1.1 safety Instructions Do noT InsTAll YoUR RECEIVER: In a closed or poorly ventilated cabinet; directly on top of or under any other equipment; on a surface which might obstruct the ventilation slots. Do noT EXPosE THE RECEIVER oR ITs ACCEssoRIEs: To direct sunlight or any other equipment that generates heat;...
the receiver. Always make backups of data on your USB storage device before using it with this receiver. STRONG will not take responsibility for any loss of information or circumstances caused by loss of information. 2.0 YoUR RECEIVER 2.1 PIn-CoDE DEfAUlT: 0000...
PART 1 • English 3. Mode indicator RED indicates that the receiver is in STANDBY mode. GREEn indicates that the receiver is in OPERATING mode. 2.3 Rear Panel Fig. 2 1. AnT In To connect to your antenna for the reception of broadcast signal. 2.
3.3 Connecting to TV with sCART cable Fig. 4 PRIMA V is also equipped with a SCART connector; alternatively, the TV set can be connected to the receiver using a good quality SCART cable. 3.4 Connecting to a Digital Audio Amplifier with s / PDIf Fig. 4...
PART 1 • English indications for a low device speed. STRONG cannot guarantee proper functioning of recoding and or Time Shift functions with all USB devices. 4.0 sTARTInG UP foR THE fIRsT TIME If you use your receiver for the first time, the Welcome “Easy install” menu appears. Use pq to move the highlight to the setting you wish to alter and use tu to change values.
5.0 QUICk GUIDE To UsInG YoUR RECEIVER We at STRONG understand that you can’t wait to enjoy your new high definition digital terrestrial receiver. The following quick guide will make you familiar with the basic operation of this device. We do, however, advice you to read the full manual to get the best performance from your receiver.
PART 1 • English 6.2 Info banner While watching TV you can press the Info button any time to get information about the current channel and event*. Press Info twice for extended EPG details about the current channel. Press Info three times for technical details about the current channel. Event information is displayed when available.
PART 1 • English noTE: Availability of EPG data depends on broadcast. 6.8 Instant Recording Your new receiver allows you to make an instant recording of the programme you are watching. Simply press RECoRD to start the recording. To enter the duration for a recording, press RECoRD again.
PART 1 • English possible. When all changes have been made, press EXIT twice. A confirmation banner will pop up. Select Yes to save the changes or No to discard. 7.1.1.3 skipping channels Channels marked with Skip will be skipped when zapping channels with the pq buttons. The channels will still be available from the channel list.
PART 1 • English Delete Press blUE in Edit Channel to enable the Delete function. The Delete sign will move up to indicate that Delete is selected. Use pq to highlight a channel and press ok to mark it for deletion. When you have marked all channels you wish to delete, press EXIT twice.
PART 1 • English Antenna Power: Set to On if you use an active antenna. When set to On, 5 V will be present on the ANT IN connector of the receiver. Select Off for passive antennas. Beeper: Select On for an audible indication of signal reception. Off turns the beeper off.
PART 1 • English Digital Audio Output: Toggles between PCM and Bitstream output. When PCM is selected, all digital audio will be converted to stereo audio. Bitstream enables multi-channel audio on HDMI for use with a Home Cinema Set. 7.3.3 local Time setting Here you can set up your region and time zone.
This submenu shows receiver specific information such as hardware version and software version. It also displays our web address www.strong.tv. Please have the Information screen on hand when you call our hotline. The person who answers your call might ask for the information given in this screen.
This receiver is equipped with an Over The Air software upgrade option. An Over The Air update might not be available in your region. Please visit our website www.strong.tv or contact your local service hotline for more information about this option.
PART 1 • English Press EXIT to quit a game. 7.6 Media+ The Media+ menu consists of the following submenus: Media Player, Record Manager, DVR HDD Information, HDD Format, and DVR Configuration Use pq to highlight the menu of choice and press ok to enter. Press EXIT to quit.
Formatting will permanently delete ALL data stored on the connected device. Please make a backup copy of all data you wish to keep before entering the HDD Format menu. STRONG cannot be held responsible for loss of data from USB devices used with this receiver.
Replace remote batteries Forgotten PIN code Default PIN is 0000 Contact local Service Hotline or send email to our Support via www.strong.tv After moving the receiver Antenna signals are too weak Press the Info button on to another room/area you...
Page 22
MP3, FLAC format Picture view: JPEG, format *STRONG cannot guarantee the playback of video files although extensions are listed, as it depends on codec used, data bit rate and resolution (all MPEG codec formats are supported). Memory and system: Flash memory:...