INSTALLATION REQUIREMENTS Parts needed: Y8 Comprx Y4 hose Gather the recommended tools and parts before starting fitting: ContaCt your !ocal installation. Read and follow the instructions provided with any sears store t0 purchase tools listed here. Kit Number 1100g. All Installations Tools needed: Flat-blade Other parts you may also need:...
Check location where dishwasher will be installed. The location Grounded electrical supply required. must provide: Do not run drain lines, water lines or electrical wiring where they • easy access to water, electricity and drain. can interfere with or contact dishwasher motor or legs.
Product and Cabinet Opening Dimensions .................._ I_ *Insulation may be compressed (not used on all models) Check that all surfaces have no protrusions that would prohibit dishwasher installation. NOTE: Shaded areas of cabinet wails show where utility connections may be installed. t1.5 *Measured from the lowest point on the...
D _!__} Req_,,_ _e_e_}_ _ Be sure that the electrical connection and wire size are A new drain hose is supplied with your dishwasher. If drain hose is not long enough, use a new drain hose with a adequate and in conformance with the National Electrical maximum length of 12 ft (3.7 m) (Part Number 3385556)
INSTALLATION INSTRUCTIONS Electrical Shock Hazard Disconnect electrical power at the fuse box or circuit breaker box before installing dishwasher. Failure to do so can result in death or electrical shock. If the water line and the cable extend to the locations shown, proceed to the "Install Drain Hose"...
Route cable from power supply through cabinet hole (cable Wood cabinet: Sand the hole until smooth. must extend to the right front side of cabinet opening). Tape cable to the floor in area shown. This will prohibit cable from Metal cabinet: Cover hole with...
Temporarily secure water line Route water line and tape it to the floor in area shown. This will keep it from moving when dishwasher is moved into cabinet Attach the water supply line (copper tubing or flexible braided opening. line) to the hot water line using a connection configuration that is in compliance with local codes and ordinances.
Fit rubber end of drain hose to waste tee and cut if needed. NOTE: Do not cut ribbed section. Attach rubber end of drain hose to Qption A; Waste disposer _ no air gap waste tee with a large drain hose ' Opti0n B;...
Option D_No waste disposer- with air cjap Tip Over Hazard Do not use dishwasher until completely installed. Do not push down on open door. Doing so can result in serious injury or cuts. 1. Connect rubber end of drain hose to air gap and cut if needed.
Helpful Tip: Place cardboard under dishwasher until installed in cabinet opening to avoid damaging floor covering. Do not use door panel as a worktable without first covering with a towel to avoid scratching the door panel. Using a 1/4" hex head socket, nut driver or Torx ® T20 ® Using two or more people, grasp sides of dishwasher door screwdriver, remove terminal box cover.
Option A_ Power Supply Cord. Electrical Shock Hazard Electrically ground dishwasher. Connect ground wire to green ground connector in terminal box. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. ii!iill iiiiii III!I _I !iiiii i i...
Connect wires black to black and white to white, using UL Listed/CSA Approved twist-on wire connectors (included with power supply cord kit). Measure height of cabinet opening from underside of countertop to floor where dishwasher will be installed (you will need to measure the lowest point on the underside of the countertop and the highest point on the floor).
Option A, Countertop Attachment Insert bracket Tabs must point Remove the brackets from the package and insert into the open Built-up floors. If the kitchen floor is higher than the cabinet slots on the left and right-hand top of the dishwasher collar as shown.
Option B, Side Attachment For marble, granite, or other hard surface countertops NOTE: Remove the brackets from the parts package. Excessive Weight Hazard Use two or more people to move and install dishwasher. Failure to do so can result in back or other injury. NOTE: Do not install kick plate until instructed to do so.
With another person holding the dishwasher to keep it from tipping, open and close the door a few times. If the door closes or falls open under its own weight, the door tension will need to When door is unlatched and door opens by itself, move the be adjusted.
Align front of dishwasher door panel with front of cabinet doors. You may need to adjust alignment to be even with your cabinets. To raise the rear of the dishwasher, adjust the rear leveling leg using a Phillips screwdriver. Turn clockwise until the dishwasher is level front to rear.
2 Add water supply line i¸¸k NOTE: To avoid vibration during operation, route the water supply line so that it does not touch the dishwasher base, frame Place paper towel under 90 ° elbow fitting. Turn on water supply or motor. and check for leaks.
Hose clamp final position Electrical Shock Hazard Electrically ground dishwasher. Connect ground wire to green ground connector in terminal box. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. After hose is connected, remove towel.
Connect wires black to black and white to white, using UL Listed/CSA Approved twist-on wire connectors (not included). Check that dishwasher is still level front-to-back and side-to- side in cabinet opening. Tighten strain relief screws to secure cable. Open dishwasher door, remove lower dish rack, and place towel over pump assembly and lower spray arm of dishwasher.
Secure dishwasher to countertop Locate brackets on top of dishwasher and secure dishwasher to countertop with two, #10 x 1/2" Phillips-head screws (included). The dishwasher must be secured to keep it from shifting when door is opened. Side mount dishwasher to cabinet NOTE: If side mounting dishwasher to cabinet, you must drill pilot holes in cabinet to avoid splitting the wood.
Option Av Install Access Panel - Plastic Panel Option B, Install Access Panel - Metal Panel Reinstall access panel and fasteners Place the plastic access panel against the dishwasher leg. Check that grounding clip is attached to the lower panel. Position the lower panel behind the access panel.
Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Check that the lower edge of the lower panel contacts the floor. Failure to follow these instructions can result in death_ Adjust if necessary.
• Read the Dishwasher User Instructions that came with your Congratulations on purchasing your water dishwasher. and energy efficient dishwasher! This dishwasher cleans by spraying the dishes Check that all parts have been installed and no steps were with water and pauses to allow the skipped.