Installing The Software - Proxim ORiNOCO AP-4900M User Manual

Installation and Initialization
Initialization
— Primary Network Name (SSID): Enter a Network Name (between 1 and 32 characters long) for the wireless
network. You must configure each wireless client to use this name as well. Note that the unit supports up to 16
SSIDs/VLANs per wireless interface. Please see the
detailed rules on configuring multiple SSIDs, VLANs, and security profiles.
NOTE: Do not use quotation marks (single or double) in the Network Name; this will cause the AP to
misinterpret the name.
— Auto Channel Select: By default, the AP scans the area for other Access Points and selects the best
available communication channel, either a free channel (if available) or the channel with the least amount of
interference. Remove the check mark to disable this option. See
Detection (DFS/RD)
NOTE: When an AP is configured to function as a Mesh AP, its channel will depend on the channel of its
Portal.
— Frequency Channel: When Auto Channel Select is enabled, this field is read-only and displays the Access
Point's current operating channel. When Auto Channel Select is disabled, you can specify the Access Point's
channel. If you decide to manually set the unit's channel, ensure that nearby devices do not use the same
frequency. Available Channels vary based on regulatory domain. See
Detection (DFS/RD)
NOTE: When an AP is configured to function as a Mesh AP, its channel will depend on the channel of its
Portal.
— Transmit Rate: Use the drop-down menu to select a specific transmit rate for the AP. The values depend on
the Operational mode. Auto Fallback is the default setting; it allows the AP unit to select the best transmit rate
based on the cell size.
• For 802.11a only -- Auto Fallback, 6, 9, 12, 18, 24, 36, 48, 54 Mbits/s.
• For 4.9 GHz Public Safety mode, the transmit rate depends on the channel bandwidth selected:
— For operation in 10 MHz bandwidth: Auto Fallback, 3, 4.5, 6, 9, 12, 18, 24, 27 Mbits/s.
— For operation in 20 MHz bandwidth: Auto Fallback, 6, 9, 12, 18, 24, 36, 48, 54 Mbits/s.
• For 802.11b only -- Auto Fallback, 1, 2, 5.5, 11 Mbits/sec.
• For 802.11g only -- Auto Fallback, 6, 9, 12, 18, 24, 36, 48, 54 Mbits/sec
• For 802.11b/g -- Auto Fallback, 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54 Mbits/sec
• For 802.11g-wifi -- Auto Fallback, 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54 Mbits/sec
NOTE: 802.11g-wifi has been defined for Wi-Fi testing purposes. It is not recommended for use in your
wireless network environment.
Additional advanced settings are available on the
Also see Security Profile
capabilities, and Configuring Security Profiles
6. Review the configuration Summary. If you want to make any additional changes, use the navigation panel on the
left-hand side of the screen to return to an earlier screen. After making a change, click Save & Next to save the
change and proceed to the next screen.
7. When finished, click Reboot on the Summary screen to restart the AP and apply your changes.

Installing the Software

Proxim periodically releases updated software for the AP on its Web site, http://support.proxim.com. Proxim recommends
that you check the Web site for the latest updates after you have installed and initialized the unit.
Download the Software
1. In your web browser, go to
for information and Available Channels
for information and Available Channels
for a description of security features,
for detailed security configuration procedures.
http://support.proxim.com.
Advanced Configuration
Dynamic Frequency Selection/Radar
for a list of available channels.
for a list of available channels.
Interfaces tab.
Management VLAN
AP-4000/4000M/4900M User Guide
chapter for information on the
Dynamic Frequency Selection/Radar
for a description of VLAN
37