Inspire M2 Assembly & Operation Manual

Inspire M2 Assembly & Operation Manual

Hide thumbs Also See for M2:

Advertisement

www.inspirefitness.net
www.inspirefitness.net
ASSEMBLY & OPERATION MANUAL
RECORD SERIAL NUMBER HERE
RECORD SERIAL NUMBER HERE
by Health In Motion LLC
Mar. 2010

Advertisement

Table of Contents
loading

Summary of Contents for Inspire M2

  • Page 1 ASSEMBLY & OPERATION MANUAL RECORD SERIAL NUMBER HERE RECORD SERIAL NUMBER HERE www.inspirefitness.net www.inspirefitness.net by Health In Motion LLC Mar. 2010...
  • Page 2 Service of your home gym should only be preformed by an authorized INSPIRE retailer. Service preformed by anyone else can result in loss of warranty. If you need help finding an authorized retailer, please contact us directly: Inspire Fitness 637 S. State College Blvd. Fullerton, CA 92831 Ph: 714-738-1729 or 877-738-1729 Fx: 714-738-1728 www.inspirefitness.net...
  • Page 3: Table Of Contents

    TABLE OF CONTENTS Section Description……………………………………………………. Page Important Safety Instructions………………………………………. Tools Required………………………………………………………………… Parts List…………………………………………………………………………. Hardware List…………………………………………………………………. Hardware Chart …………………………………………………………….. Cable Chart ……………………………………………………………………. Assembly Instructions……………………………………………………. Decal Reference……………………………………………………………… Decal Placement……………………………………………………………… Accessories……………………………………………………………………… General Maintenance Information…….…………………………… Maintenance Schedule…….……………………………………………… Limited Warranty……………………………………………………………..
  • Page 4: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS Please read this entire manual and familiarize yourself with all decals and warnings before using this home gym. • WARNING! It is necessary to inspect this home gym regularly to maintain safety and proper function. Please use the maintenance schedule included towards the back of this manual.
  • Page 5: Parts List

    M2 PARTS & HARDWARE LIST Item Parts Description Item Hardware Description Qty Rec'd Qty Rec'd Base Beam Bolt, 1/4-20 x 3/8" L (Phillips head) Rear Base Bolt, 1/4-20 x 3" L (Button Head) Backing Plate Bolt, 5/16-18 x 1-1/4" L...
  • Page 6: Hardware Chart

    HARDWARE CHART PAGE 3...
  • Page 7 HARDWARE CHART PAGE 4...
  • Page 8: Cable Chart

    CABLE CHART UPPER CABLE MIDDLE CABLE LOWER CABLE PAGE 5...
  • Page 9: Assembly Instructions

    ASSEMBLY INSTRUCTIONS PAGE 6...
  • Page 10 Foot Plate Main Base NOTE: Use Outside Holes in Step 1. STEP 2 1 - 3” Hex Bolt 2 - 3/8” Small OD Washers 1 - 3/8” Lock Nut Do Not Over Tighten STEP 1 2 - 3” Hex Bolts 4 - 3/8”...
  • Page 11 Guide Rods STEP 4 Shroud Plate Holes must line up STEP 3 2 - 3 ¾” Hex Bolts 4 - 3/8” Flat Washers 2 - 3/8” Lock Nuts FINGER TIGHTEN ONLY! STEP 3: Attach Guide Rods to Rear Base using: Two (3/8”...
  • Page 12 IMPORTANT! STEP 6 Guide Rods must be 2 - 1 ¾” Hex Bolts in Front of plate. 4 - 3/8” Flat Washers 2 - 3/8” Lock Nuts FINGER TIGHTEN ONLY Main Upright STEP 5 2 - 4” Hex Bolts 4 - 3/8” Flat Washers 2 - 3/8”...
  • Page 13 Note: Attach left and right top beams with “Inspire” logo facing out. Right Top Beam Plate Left Top Beam Plate 1” Bolt 1” Bolt STEP 7 2 - 4” Hex Bolts 2 - 1” Hex Bolts 6 - 3/8” Flat Washers 2 - 3/8”...
  • Page 14 Press Arm Bearings Use Small OD Washers on the Outside of the Press Arm Bearings STEP 8 4 – 1” Hex Bolts 4 – 3/8” Small OD Washers 4 – 3/8” Flat Washers 4 – 3/8” Lock Nuts STEP 9 2 –...
  • Page 15 STEP 10 Install Four Pulleys PULLEY 1 1 - 3 ¾” Hex Bolt 2 - 1” Step Spacers 1 - 3/8” Lock Nut 4 ½” Pulley 1 - 2” Hex Bolt 2 - 3/8” Flat Washers 1 - 3/8” Lock Nut PULLEY 2 3 ½”...
  • Page 16 STEP 13 2 – Lat Bar Holders 1 – 4 ¾” Hex Bolt 1 – 3” Spacer Tube 2 – 3/8” Flat Washers 1 – 3/8” Lock Nut STEP 12 1 – 4 ½” Wide Pulley Pulley 6 1 – 4” Hex Bolt 2 –...
  • Page 17 STEP 14 Install Six Pulleys & One Cable Retaining Bolt TIGHTEN THESE BOLTS NOW 1 – 4 ½” Pulley 1 – 3 ¾” Hex Bolt 2 – 1” Step Spacers PULLEY 7 1 – 3/8” Lock Nut 1 – 3 ½” Pulley 1 –...
  • Page 18 NOTE: Once Assembled, slide rubber washer against plastic ball STEP 16 1 – Plastic Ball 1 – Cable “U” Bracket 1 – 1 ¼ “ Shoulder Bolt 1 – Spring Clip 1 – 5/16” Lock Nut Pulley 13 NOTE: CABLE GOES INSIDE FRAME TUBE Press Arm Mount STEP 15 2 –...
  • Page 19 STEP 19 STEP 18 1 – Floating Pulley Bracket 1 – 3 ½” Pulley 2 – Floating Pulley Plates 1 – Cable Adapter 2 – 3 ½” Pulleys 1 – 2” Hex Bolt 2 – 1 3/4” Hex Bolts 2 – 3/8” Flat Washers 4 –...
  • Page 20 STEP 20 1 – Plastic Ball 1 – Cable “U” Bracket 1 – 1 ¼ “ Shoulder Bolt 1 – Spring Clip 1 – 5/16” Lock Nut STEP 22 1 – Plastic Ball 1 – Cable “U” Bracket 1 – 1 ¼ “ Shoulder Bolt 1 –...
  • Page 21 Backpad Tilt Frame Main Upright STEP 23 Attach Backpad Tilt Frame STEP 24 with Roller Tube 1 – ¼-20 x 3” Button Head Bolt 1 – ¼-20 Flat Head Nut STEP 25A Attach Rollers STEP 25B 2 – ¼-20 x 3/16” long Setscrews Roller Tube Mount Step 23: Attach Backpad Tilt Frame to Main Upright with the Roller Tube as shown in diagram.
  • Page 22 Note: To assemble orthopedic pads, place pad on Seat Base. Work the edge of pad into the groove of the Seat Base on all sides. Do not use sharp objects during installation. Seat Base STEP 28 Seat Stem 2 – 1 ¾” Hex Bolts 2 –...
  • Page 23 STEP 31 1 – ¼” Phillips Head Screw 1 – ¼” Flat Washer STEP 30 1 – 6” Hex Bolt 2 – ½” Flat Washers 1 – ½” Lock Nut Step 30: Attach Press Arm to Press Arm Mount using: One (1/2”...
  • Page 24 STEP 32 IMPORTANT! Cable Bolt must be fully threaded Remove Bolts from Guide Rods into Selector Stem with Jam Nut tightened securely before using. Failure to do so may cause cable to come loose from weights and cause injury. STEP 33 Install Weight Stack Risers, Rubber Donuts, Weight Stack, Top Weight/Selector Stem...
  • Page 25 Note: Be sure guide rods are positioned STEP 34 in front of plate. 2 – 1 ¾” Hex Bolts 4 – 3/8” Flat Washers 2 – 3/8” Lock Nuts Shroud Plate Assembly STEP 35 1 – 2 ½” Hex Bolt 2 –...
  • Page 26 STEP 36 Install Fabric Shroud Top Shroud Plate Shroud Plate Adjustment Bolts Bottom Shroud Plate Step 36: To install Fabric Shroud, start at the front of the top shroud plate and wrap the edge of the fabric shroud around the shroud plate. Pull tight as you wrap and make sure that the velcro rim on the fabric shroud seals firmly to the velcro rim on the Shroud Plate.
  • Page 27 STEP 37 STEP 38 Note: When not in use, EZ curl bar or Lat Bar can be stored in the accessory holder. STEP 39 Step 37: Attach Lat Bar to High Pulley with Spring Clip Step 38: Attach “D” Handles to Mid Pulley with Spring Clip Step 39: Attach Revolving EZ Curl Bar to Chain, then Chain to Low Pulley with Spring Clips Page 24...
  • Page 28 STEP 41 Press Arm Stop STEP 40 Cable Bolt Jam Nut Selector Stem Step 40: Verify that Cable Bolt is threaded at least ½” into Selector Stem. Wrench tighten Jam Nut. NOTE: At this point it is necessary to seat the cables. Start by verifying that cables are centered in the grooves of all pulleys.
  • Page 29: Decal Reference

    DECAL REFERENCE PAGE 26...
  • Page 30 DECAL REFERENCE PAGE 27...
  • Page 31: Decal Placement

    “This product Patent Pending” placed just above the “Notice” label “Do Not Hang From (60 x 40) Press Arm” below M2 label (50mm) Round “NOTICE” on side of upright, beside head pad “WARNING Use only (40 x 170) genuine INSPIRE replacement parts”...
  • Page 32: Accessories

    ACCESSORIES • Exercise Wall Chart • Lat Bar • Revolving EZ Curl Bar • Ankle Strap • Abdominal Strap Handle HOME GYM OPTIONS • Heavy Stack (50lbs.) • Colored Orthopedic Pads • Colored Shroud • Leg Press • Ab Crunch Bar Training Tips CONSULT A PHYSICIAN BEFORE STARTING ANY EXERCISE PROGRAM 1.
  • Page 33: General Maintenance Information

    GENERAL MAINTENANCE INFORMATION Warning: DO NOT place styrofoam or printed materials on the orthopedic seat pads. Over time, these may stick to the pads and mar the surface. Do not leave items sitting on the orthopedic seat pads, these pads have a special density that takes shape to objects and small objects will leave imprints in the surface that may take time to come out.
  • Page 34: Maintenance Schedule

    MAINTENANCE SCHEDULE HOME ROUTINE ENTRY DATE MAINTENANCE Inspect: Links, Pull Pins, WEEKLY Spring Clips, Swivels, Weight Stack Pins WEEKLY Clean: Upholstery Inspect: Cables and WEEKLY their Fittings Inspect: Tautness of all WEEKLY Shrouds Inspect: Accessory Bars 3 MONTHS and Handles 3 MONTHS Inspect: All Decals Inspect: All Nuts and...
  • Page 35: Limited Warranty

    LIMITED WARRANTY In-Home Lifetime Warranty. This Warranty applies only in the United States to Inspire strength products manufactured or distributed by Health In Motion LLC. The warranty period to the original purchaser is lifetime of the original purchaser. Health In Motion warrants that the Product you have purchased for non-commercial, personal, family or household use from Health In Motion LLC or from an authorized Health In Motion reseller is free from defects in materials or workmanship under normal use during the warranty period.

Table of Contents