Oven Light Bulb Replacement; Power Failure - DCS RGT-305 Use And Care Manual

CARE AND MAINTENANCE
OVEN RACkS, ROllERS AND RACk SUppORTS
All of the oven racks and 12" rack supports are chrome plated steel. The roller assisted rack supports in the
main oven (24" and 27") are stainless steel. To remove the 12" oven rack supports, first remove the oven racks,
then grasp the rack supports and pull up and out. To replace the rack supports, put the top in first. To clean,
use a damp sponge, cloth, or steel wool with a mild detergent. Chrome cleaners, such as soft scrub, Cameo or
Bar keepers Friend can be applied with a damp sponge following package directions. Rinse and dry. Powdered
cleaners such as Bon-Ami or Comet are applied with a damp sponge or cloth, rubbed lightly, rinsed and dried. For
hard to remove food soil use a dampened soap filled steel wool pad, rinsed and dried. Harsh Cleaners which are
commercial oven cleaners, such as Easy off or dow can be used on the racks, but are not recommended for use on
the self cleaning oven rack rollers or oven interiors. Additionally, some commercial oven cleaners cause darkening
and discoloration. Test the cleaner on a small part of the rack and check for any discoloration before cleaning the
entire rack. Apply a generous coating. Allow to stand for 15 to 20 minutes. Rinse thoroughly and dry. After be-
ing cleaned, if the racks in the main oven do not slide easily, pour a small amount of cooking oil on a paper towel
and rub it lightly over the side rails and rollers. spray with "Pam" if racks get hard to move.
fRAME, SIDES, DOOR ExTERIOR, hEAT DEflECTOR
These parts are made of stainless steel, follow the directions for the Backguard. Take care when cleaning the door
top, and do not let water or cleaners run down the vents. If water or cleaners spill into the vents, they may streak
the glass inside the door.
DOOR GASkET
Clean with hot water only. do not rub. Press a dry towel on the gasket to dry. do not remove or damage the
mesh.

OVEN lIGhT bUlb REplACEMENT

For oven light bulb replacement use only a 40 watt, 120 volt appliance light bulb. These are available in super-
markets. do NoT use a standard light bulb in any oven, the heat will break it.
To replace the Light Bulb
1. Be sure the oven light bulb switch is in the "oFF" position or turn off circuit breaker. The bottom of the switch is
pressed in. Let the cover and the bulb cool completely.
2. Remove the light cover. Turn the cover to the left (counterclockwise) to unscrew it.
3. Remove the burnt out bulb. Replace it with a 40 watt appliance light bulb only.
4. Replace cover. Turn circuit breaker back on, if turned off. (see Warning below).
WARNING!
Be sure the oven light switch is in the off position and the cover is cool. if the bulb comes loose from the base, turn
off the power to the oven at the circuit breaker panel, before attempting to remove the bulb base from the socket.

pOWER fAIlURE

To light the cooktop burners, turn the control knob to "lITE", hold a lighted match to the port ring. After the
flame is burning all the way around the burner, adjust the flame. It is necessary to light each burner separately,
each time you want to use it. do not attempt to match light the griddle, grill, broil, or oven burners; they will not
function without any electrical power. Make sure knobs are in the "oFF" position should power be restored and
you are away from the unit. do not leave the burner unattended. The burner will not relight if blown out.
26