Infinite Phaser; Ring Modulator; Step Ring Modulator; Tremolo - Roland JUNO-Di Editor Owner's Manual

Effects List
14:

INFINITE PHASER

A phaser that continues raising/lowering the frequency at which the
sound is modulated.
fig.MFX-14
L in
Infinite Phaser
R in
Parameter Value
Mode 1, 2, 3, 4
Speed # -100–+100
Resonance # 0–127
Mix # 0–127
Pan # L64–63R
Low Gain -15–+15 dB
High Gain -15–+15 dB
Level
0–127
15:

RING MODULATOR

This is an effect that applies amplitude modulation (AM) to the input
signal, producing bell-like sounds. You can also change the
modulation frequency in response to changes in the volume of the
sound sent into the effect.
fig.MFX-15
L in
Ring Mod 2-Band EQ
R in
Ring Mod 2-Band EQ
Parameter Value
Frequency # 0–127
Sens # 0–127
Polarity UP, DOWN
Low Gain
-15–+15 dB
High Gain -15–+15 dB
D100:0W–
Balance #
D0:100W
Level 0–127
70
Pan L
2-Band EQ
Pan R
Explanation
Higher values will produce a
deeper phaser effect.
Speed at which to raise or lower
the frequency at which the sound
is modulated
(+: upward / -: downward)
Amount of feedback
Volume of the phase-shifted
sound
Panning of the output sound
Amount of boost/cut for the
low-frequency range
Amount of boost/cut for the
high-frequency range
Output volume
L out
R out
Explanation
Adjusts the frequency at which modulation is
applied.
Adjusts the amount of frequency modulation
applied.
Determines whether the frequency
modulation moves towards higher
frequencies (UP) or lower frequencies
(DOWN).
Gain of the low frequency range
Gain of the high frequency range
Volume balance between the direct sound
(D) and the effect sound (W)
Output level
16:

STEP RING MODULATOR

This is a ring modulator that uses a 16-step sequence to vary the
frequency at which modulation is applied.
fig.MFX-16
L out
L in
Step Ring Mod
R in
R out Step Ring Mod
Parameter
Step 01–16
Rate #
Attack #
Low Gain
High Gain
Balance #
Level
You can use multi-effect control to make the step sequence play
again from the beginning (p. 65).
17:

TREMOLO

Cyclically modulates the volume to add tremolo effect to the sound.
fig.MFX-17a
L in
Tremolo
R in
Tremolo
Parameter Value
TRI, SQR, SIN, SAW1,
SAW2
Mod Wave
Rate # 0.05–10.00 Hz, note
Depth # 0–127
Low Gain
-15–+15 dB
High Gain -15–+15 dB
Level 0–127
2-Band EQ
2-Band EQ
Value Explanation
Frequency of ring modulation at
0–127
each step
Rate at which the 16-step sequence
0.05–10.00 Hz, note
will cycle
Speed at which the modulation
0–127
frequency changes between steps
Amount of boost/cut for the
-15–+15 dB
low-frequency range
Amount of boost/cut for the
-15–+15 dB
high-frequency range
Volume balance of the original
D100:0W–D0:100W
sound (D) and effect sound (W)
0–127 Output volume
2-Band EQ
2-Band EQ
Explanation
Modulation Wave
TRI: triangle wave
SQR: square wave
SIN: sine wave
SAW1/2: sawtooth wave
SAW1 SAW2
Frequency of the change
Depth to which the effect is applied
Gain of the low range
Gain of the high range
Output Level
L out
R out
L out
R out