Usb Settings; Selecting The Usb Mode; Usb Audio; Setting The Usb Audio Output - Denon FN-X1700 Owner's Manual

USB Settings

Selecting the USB mode

The respective functions given below are carried out in the operation
modes of the USB A terminal (USB host mode) and USB B terminal
(USB device mode).
USB A :
• Preset data import/export function
• Version upgrading
USB B :
• USB audio interface function
• USB MIDI interface function
The operation mode to be established when the unit's
power is turned on can be selected by a Utility setting.
(Factory setting: USB A)
To switch from USB A (host mode) to USB B (device mode):
1
UTILITY/–USB A/USB B
Press the
second.
2
Operation now transfers to the screen shown below.
3
EFX SELECT
Select OK/Cancel using the
(EFX2), and press the button to enter the selection.
4
The indicator changes from USB-A to USB-B, and the
device mode is established.
(* When a specific period of time elapses with no
computer connected to the USB B terminal, the
indicator changes back to USB-A, and the host mode
is automatically selected.)
5
To select the host mode again, press the
A/USB B
button for one second, and select the settings
by following the same steps.

USB audio

This unit features a 24-bit 96 kHz USB audio input/output sound card
function which supports up to 8 channels (4 stereo systems). The
sampling frequency can be set to 44.1 kHz, 48 kHz or 96 kHz using a
Utility setting (factory setting: 96 kHz).
* When the unit is connected to a computer which runs Windows XP ,
Vista or a similar operating system, install DENON DJ ASIO driver
Ver2 contained on the CD-ROM provided. If the Ver1 driver is already
installed, first uninstall it, and then install the Ver2 driver.
* Depending on the computer used, select the PC/MAC section
settings under System Setting among the Utility settings.

Setting the USB audio output

button for one
Any sound source of the 4 systems provided—1 to 4 input channels
(Pre EQ), mic input (Post Send VR), master output (Pre Limiter) or
REC output—can be selected as the USB audio output.
The USB audio output level can be adjusted using a Utility setting.
1 UTILITY/–USB A/USB B
Press the
setting screen is displayed.
2 EFX SELECT
Using the
Setting USB Audio Setting
Select. One of the audio sources assigned to the USB
output channels is selected on the selection screen
displayed.
control
3 UTILITY/–USB A/USB B
Press the
setting screen is closed.
UTILITY/–USB

Setting the USB audio input

One of the two modes below is set using the
ASSIGN CH/MASTER
assignment destinations.
The LED on the side corresponding to the mode
selected lights.
The USB audio input levels can be adjusted using
Utility settings. The adjustment values are stored on a
mode by mode basis.
q CH INPUT mode
Select this mode when mixing sound using only the DN-X1700
without using the mixer functions of the DJ software.
The USB audio input signals are assigned using the configuration
shown below.
USB channel 1 and 2 inputs
USB channel 3 and 4 inputs
USB channel 5 and 6 inputs
USB channel 7 and 8 inputs
w MASTER mode
Select this mode when using both the mixer functions of the DJ
button. The Utility
software and the DN-X1700's functions.
The USB audio input signals are assigned to the buses shown
below.
control (EFX2), select Audio
Output Source USB channel 1 and 2 inputs
USB channel 3 and 4 inputs
USB channel 5 and 6 inputs
USB channel 7 and 8 inputs
The mixer output of the DJ software is mixed in the buses using
the DN-X1700.
button. The Utility
* Ensure that the audio output settings of the DJ software correspond
to the specifications given above.
USB
button for the USB audio input
Input channel 1
Input channel 2
Input channel 3
Input channel 4
Master bus
Cue monitor bus
Disabled
Disabled
13