Clarke Woodworker CBS12WV Operating & Maintenance Manual

Clarke Woodworker CBS12WV Operating & Maintenance Manual

305mm (12”) portable bandsaw

Advertisement

©
1000
305mm (12") Portable Bandsaw
Model CBS12WV
Part Number 6460030
OPERATING & MAINTENANCE
INSTRUCTIONS

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Woodworker CBS12WV and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Clarke Woodworker CBS12WV

  • Page 1 © 1000 305mm (12”) Portable Bandsaw Model CBS12WV Part Number 6460030 OPERATING & MAINTENANCE INSTRUCTIONS...
  • Page 2 © Copyright Clarke International. October, 2000. All rights reserved...
  • Page 3: Specifications

    Logs or round timber. Spare Parts & Service Contacts For Spare Parts and Service, please contact your nearest dealer, or CLARKE International, on one of the following numbers. PARTS & SERVICE TEL: 020 8988 7400 PARTS & SERVICE FAX: 020 8558 3622 e-mail as follows: PARTS: Parts@clarkeinternational.com...
  • Page 4: For Your Own Safety

    Thank you for purchasing this Clarke 12 inch Bandsaw. This machine is designed to rip and cross cut wood exclusively and for DIY, and hobby use ONLY. Before attempting to operate this machine, please read this instruction manual thoroughly and follow all directions carefully.
  • Page 5: Electrical Connections

    Electrical Connections WARNING! THIS APPLIANCE MUST BE EARTHED IMPORTANT: The wires in the mains lead are coloured in accordance with the following code: Green & Yellow Earth Blue Neutral Brown Live As the colours of the flexible cord of this appliance may not correspond with the coloured markings identifying terminals in your plug proceed as follows: •...
  • Page 6 Fig. (1) Main Components Table Insert Front Cover Blade Tensioning Screw Front Cover Securing Knob (x4) Blade Guard Rip Fence/ Mitre Gauge Upper Blade Guide Table Set Screw Dust Extraction Port Control Panel (ON/OFF) Feet Speed Control Knob (1) Attach the Feet (Ref: fig 1) 1.
  • Page 7 Fig. (2) Cover Removed 15 18 Foot Securing screw (x4) Drive Wheel Lower Blade Guide Control Panel (On/Off/Speed) Microswitch Motor Cover Securing Screws Fig. (3) Rear View Table Securing Knobs (x2) Table Adjusting Screw Table Tilt Bracket Motor Cover Table Tilt Indicator (Degrees) Dust Extraction Outlet...
  • Page 8 (3) Attach the Bandsaw to a Workbench Fix the bandsaw to a suitable Workbench using screws or bolts (not supplied), through the holes in the feet with washers under the screw heads. Do not overtighten the securing screws. Adjustments IMPORTANT: To achieve the best performance and maintain the maximum level of safety, certain adjustments must be made, BEFORE use.
  • Page 9 1. Remove the table by fully unscrewing the two securing knobs, then slacken off all upper and lower blade guides as described under ‘Blade Guide Adjustments’ on page 10. 2. Correctly tension the blade as described under ‘Blade Tension’ on page 8. 3.
  • Page 10 (d) Blade Guide Adjustments (Ref: fig 5) NOTE: These adjustment are carried out at the factory. It is not therefore necessary to check or make readjustments before using for the first time. These adjustments MUST be carried out periodically or whenever replacing a saw blade or whenever blade tracking adjustment is carried out.
  • Page 11: Operation

    A dust extractor may be used during use. Simply connect a suitable hose (not supplied), from the dust extractor, to the dust extractor port (23, Fig.3). Dust Extractors are available from your Clarke dealer. • The saw is supplied with a mitre gauge to allow mitre cuts to be made.
  • Page 12: Maintenance

    IMPORTANT: Before plugging in to the mains supply, the blade guard MUST be adjusted so that a minimum amount of blade is visible when cutting takes place. This is achieved as follows: Offer the workpiece up to the blade, then lower the Upper Blade Guard by slackening the locking knob, (23, Fig.4) and tightening it again when the guard is as close to the workpiece as possible without interference.
  • Page 13: Fault Finding

    Replacement blades are available from your local dealer or Clarke International Spare Parts Department. 1. Remove the table by first removing the table set screw then fully unscrewing the securing knobs.
  • Page 14: Spare Parts List

    Spare Parts List Description Part No. Description Part No. Front Cover HT14605601 Wheel HT14600203 Wheel Body HT14605601 Hex Nut HT270100312 Machine Screw HT2651047112 Mitre Shaft HT2601008112 Angle Pointer HT14302401 Knob Screw HT14601101 Machine Screw HT2651010113 Switch Box HT14601201 Insert Plate HT14606201 Machine Screw HT2651011112...
  • Page 15: Spare Parts Diagram

    Spare Parts Diagram...

Table of Contents

Save PDF