Page 1 OMC-2301 GEPON OLT Management Card User’s Guide Version 3.60 11/2007 Edition 1 www.zyxel.com...
Page 3: About This User's Guide
About This User's Guide Intended Audience This manual is intended for people who want to configure the OMC-2301 GEPON (Gigabit Ethernet Passive Optical Network) OLT (Optical Line Terminal) Management Card using the web configurator or via commands. You should have at least a basic knowledge of TCP/IP networking concepts and topology.
Page 4: Document Conventions
Syntax Conventions • The OMC-2301 GEPON OLT Management Card may be referred to as the “OMC-2301”, the “OMC”, the “management card”, the “device” or the “system” in this User’s Guide. • “OLT-2300” refers to the OLT-2300 system including the main chassis and their cards.
Page 5 Document Conventions Icons Used in Figures Figures in this User’s Guide may use the following generic icons. OLT-2300 Computer Server Switch Router Internet Central Office/ISP Splitter OMC-2301 User’s Guide...
Page 6: Safety Warnings
• Warning! To avoid risk of electric shock, remove only one card at a time and do not place fingers or objects inside the chassis. Cover empty slots with slot covers. This product is recyclable. Dispose of it properly. OMC-2301 User’s Guide...
Page 7 Safety Warnings OMC-2301 User’s Guide...
Page 8 Safety Warnings OMC-2301 User’s Guide...
Page 9: Table Of Contents
Syslog ............................133 MAC Table ..........................137 IGMP Table ..........................141 Commands, Troubleshooting and Specifications ............143 Introducing the Commands ..................... 145 Command Examples ....................... 175 Troubleshooting ........................191 Product Specifications ......................203 Appendix and Index ......................207 OMC-2301 User’s Guide...
Page 10 Contents Overview OMC-2301 User’s Guide...
Page 11: Table Of Contents
2.3 Hardware Connection ......................32 2.3.1 Console Port ......................32 2.3.2 Alarm Port Pin Assignments ..................32 2.3.3 Power Connector ....................... 33 Part II: Basic Setup ................35 Chapter 3 The Web Configurator ......................37 3.1 Introduction .......................... 37 OMC-2301 User’s Guide...
Page 12 6.7 DBA (Dynamic Bandwidth Allocation) ................. 64 6.8 EPON Common Setup ...................... 65 6.9 ONU Setup ......................... 67 6.10 EPON Profile ........................69 6.11 Introduction to VLANs ....................... 73 6.11.1 Port-based VLANs ....................74 6.12 4-Port ONU Profile ......................74 OMC-2301 User’s Guide...
Page 13 Destination Filter........................101 11.1 Overview .......................... 101 11.2 Destination Filter Status ....................101 11.3 Destination Filter Setup ....................102 11.3.1 Example: Destination Filter ..................103 Chapter 12 Port Authentication....................... 105 12.1 Overview .......................... 105 12.1.1 RADIUS ......................... 105 OMC-2301 User’s Guide...
Page 14 14.6 ONU Device Reset ......................126 14.7 OMC Firmware Upgrade ....................126 14.8 Restore Configuration ..................... 127 14.9 Backup Configuration ..................... 127 14.10 FTP Command Line ...................... 128 14.10.1 Filename Conventions ..................128 14.10.2 FTP Command Line Procedure ................129 OMC-2301 User’s Guide...
Page 15 19.3 The Login Screen ......................148 19.4 Command Syntax Conventions ..................148 19.5 Changing the Password ....................148 19.6 Command Modes ......................149 19.7 Getting Help ........................150 19.7.1 List of Available Commands ................... 150 19.7.2 Detailed Command Information ................151 OMC-2301 User’s Guide...
Page 16 20.8.4 Resetting to the Factory Default ................184 20.9 no Command Examples ....................185 20.9.1 no port-access-authenticator .................. 185 20.9.2 no ssh ........................185 20.10 priority-profile Commands ..................... 186 20.11 onu Commands ......................187 20.12 vlan-profile Commands ....................188 Chapter 21 Troubleshooting........................191 OMC-2301 User’s Guide...
Page 17 21.6.1 Internet Explorer Pop-up Blockers ................. 197 21.6.2 JavaScripts ......................200 21.6.3 Java Permissions ....................201 Chapter 22 Product Specifications ......................203 Part VI: Appendix and Index ............... 207 Appendix A Legal Information ....................209 Appendix B Customer Support..................... 213 Index............................219 OMC-2301 User’s Guide...
Page 18 Table of Contents OMC-2301 User’s Guide...
Page 19: List Of Figures
Figure 33 VLAN Profile: Example 2: Classifier Filter Profile ..............91 Figure 34 Priority Profile ........................94 Figure 35 Priority Profile: Example ......................96 Figure 36 Static MAC Forwarding Status ....................97 Figure 37 Static MAC Forwarding ......................98 Figure 38 Destination Filter Status ...................... 101 OMC-2301 User’s Guide...
Page 20 Figure 76 Example Xmodem Upload ....................197 Figure 77 Pop-up Blocker ........................198 Figure 78 Internet Options ........................198 Figure 79 Internet Options ........................199 Figure 80 Pop-up Blocker Settings ....................... 199 Figure 81 Internet Options ........................200 OMC-2301 User’s Guide...
Page 21 Figure 82 Security Settings - Java Scripting ..................201 Figure 83 Security Settings - Java ......................202 Figure 84 Java (Sun) ..........................202 Figure 85 Console Cable RJ-11 Male Connector ................. 205 Figure 86 Console Cable DB-9 Female Connector ................206 OMC-2301 User’s Guide...
Page 22 List of Figures OMC-2301 User’s Guide...
Page 23: List Of Tables
Table 33 Access Control Overview ...................... 109 Table 34 SNMP Commands .........................111 Table 35 SNMP Traps ...........................111 Table 36 Access Control: SNMP ......................112 Table 37 Access Control: Logins ......................113 Table 38 Access Control: Service Access Control ................118 OMC-2301 User’s Guide...
Page 24 Table 56 priority-profile Commands ..................... 171 Table 57 vlan-profile Commands ......................172 Table 58 Default Settings ........................203 Table 59 OMC-2301 Specifications ..................... 203 Table 60 OLT-2300 Features ....................... 204 Table 61 Console Cable Connector Pin Assignments ................. 206 OMC-2301 User’s Guide...
Page 25: Introduction
Introduction Introducing the OMC (27) Hardware (31)
Page 27: Introducing The Omc
Fiber Ethernet or Fiber The OMC-2301 (GEPON OLT Management Card) centralizes the management of all of the GEPON OLT line cards. You can configure and maintain the OLT line cards through the OLT management card; thus eliminating the need to connect to each line card individually.
Page 28: Ways To Manage The Omc
• Change the password. Use a password that’s not easy to guess and that consists of different types of characters, such as numbers and letters. • Write down the password and put it in a safe place. OMC-2301 User’s Guide...
Page 29 If you forget your password, you will have to reset the OMC to its factory default settings. If you backed up an earlier configuration file, you would not have to totally re- configure the OMC. You could simply restore your last configuration. OMC-2301 User’s Guide...
Page 30 Chapter 1 Introducing the OMC OMC-2301 User’s Guide...
Page 31: Hardware
The OMC is functioning normally. ALM 2 A traffic error (such as Bit Error Rate (BER), Dying Gasp, Errored Frames, bad encryption key or LLID mismatch) occurs on a line card. There is no traffic error on a line card. OMC-2301 User’s Guide...
Page 32: Hardware Connection
(COM1, COM2 or other COM port) of your computer. 2.3.2 Alarm Port Pin Assignments This section explains the connections to the ALM port on the management card. The ALM port is a male 9-pin connector. OMC-2301 User’s Guide...
Page 33: Power Connector
Connect the alarm output pins to another piece of equipment so the OMC-2301 can notify it of an alarm. The OMC-2301 signals an alarm when it detects an alarm on the ALM input pins or in the OMC system (for example, the voltage or temperature is outside the normal range). To signal an alarm, the OMC opens the circuit for pins 1 and 6 (the common pin) and closes the circuit for pins 2 and 6.
Page 34 Chapter 2 Hardware OMC-2301 User’s Guide...
Page 35: Basic Setup
Basic Setup The Web Configurator (37) Initial Setup Example (43) System Status and Port Statistics (47) Basic Setting (57)
Page 37: The Web Configurator
4 The login screen appears. The default username is admin and associated default password is 1234. The date and time display as shown if you have not configured a time server nor manually entered a time and date in the General Setup screen. OMC-2301 User’s Guide...
Page 38: The Status Screen
The Status screen is the first screen that displays when you access the web configurator. Figure 7 Web Configurator: Home Screen (Status) In the navigation panel, click a main link to reveal a list of submenu links. Table 4 Navigation Panel Sub-links Overview ADVANCED BASIC SETTING MANAGEMENT APPLICATION OMC-2301 User’s Guide...
Page 39: Table 5 Web Configurator Screen Sub-Links Details
MAC addresses for each fiber port. Forwarding These static MAC addresses do not age out. Destination Filter This link takes you to screens where you can view and configure the actions on Profile Status traffic from specified ONUs. OMC-2301 User’s Guide...
Page 40: Change Your Password
3.4 Device Lockout You can be locked out from managing the OMC if another administrator is currently logged in with the admin user name. You must wait until the other administrator has logged out before you can log in. OMC-2301 User’s Guide...
Page 41: Resetting The Omc
“ ” message. atlc Enter Debug Mode 5 Wait for the “ ” message before activating XMODEM Starting XMODEM upload upload on your terminal. 6 After a configuration file upload, type to restart the OMC. atgo OMC-2301 User’s Guide...
Page 42: Logging Out Of The Web Configurator
Figure 10 Web Configurator: Logout Screen 3.7 Help The web configurator’s online help has descriptions of individual screens and some supplementary information. Click the Help link from a web configurator screen to view an online help description of that screen. OMC-2301 User’s Guide...
Page 43: Initial Setup Example
Follow the steps below to connect the devices for the simple test network. 1 Insert an OLC-2301 in the first slot of the OLT 2300. 2 Connect the Gigabit Ethernet port on the OLC-2301 to a Gigabit port on a switch that has access to the Internet. OMC-2301 User’s Guide...
Page 44: Creating A Service Profile
ONU name “Default” of Port 101 in the table below. Enter a new descriptive name in the ONU Name field (for example, “TestSetup”). 7 In the MAC Address field, select the second radio button and the ONU’s MAC address from the drop-down list box. OMC-2301 User’s Guide...
Page 45: Testing The Internet Connection
Make sure the computer is set to use a dynamic IP address. 2 Open a web browser and enter any web site address (for example, www.zyxel.com). When the web site displays, you have successfully accessed the Internet through the PON. OMC-2301 User’s Guide...
Page 46 Chapter 4 Initial Setup Example OMC-2301 User’s Guide...
Page 47: System Status And Port Statistics
Table 7 Status LABEL DESCRIPTION System Up This field shows how long the system has been running since the last time it was Time started. Slot ID This field displays the slot number of a line card. OMC-2301 User’s Guide...
Page 48: Epon Info
Click a number in the PON Port column in the Status screen to display general fiber port information. Use this screen to check the status and general performance data on connections to the ONUs. Figure 13 Status: EPON Info OMC-2301 User’s Guide...
Page 49: Epon Details
Set Interval. Stop Click Stop to stop port statistic polling. 5.2.2 EPON Details To view detailed EPON statistics, click an LLID number in the EPON Info screen to display the EPON Details screen. OMC-2301 User’s Guide...
Page 50: Figure 14 Status: Epon Info: Epon Details
Chapter 5 System Status and Port Statistics Figure 14 Status: EPON Info: EPON Details OMC-2301 User’s Guide...
Page 51 Chapter 5 System Status and Port Statistics OMC-2301 User’s Guide...
Page 52: Table 9 Status: Epon Info: Epon Details
This field displays the number of frames transmitted successfully through the PON. Total Tx Dropped This field displays the number of transmitted frames dropped on the PON. Total Rx Dropped This field displays the number of received frames dropped on the PON. OMC-2301 User’s Guide...
Page 53 This field displays the number of priority 3 frames transmitted to the ONU. P2P Frames Received OK This field displays the number of peer-to-peer frames received. Dropped by Policier This field displays the number of peer-to-peer frames dropped by a policy. OMC-2301 User’s Guide...
Page 54 Duplicate Event This field displays the number of event notifications with a sequence number Notification Rx that is equal to the last event notification received. Loopback Control This field displays the number of loopback control packets transmitted. OMC-2301 User’s Guide...
Page 55: Ethernet Port Details
5.2.3 Ethernet Port Details Click a number in the Uplink Port column in the Status screen to display Ethernet port statistics. Use this screen to check status and detailed performance data about an Ethernet uplink port on the OLC-2301. OMC-2301 User’s Guide...
Page 56: Figure 15 Status: Port Details
The text box displays how often (in seconds) this screen refreshes. You may change Interval(s) the refresh interval by typing a new number in the text box and then clicking Set Interval. Stop Click Stop to stop port statistic polling. OMC-2301 User’s Guide...
Page 57: Basic Setting
6.2 System Information In the navigation panel, click Basic Setting > System Info to display the screen as shown. You can check the firmware version number and monitor the OLT temperature, fan speeds and voltage in this screen. OMC-2301 User’s Guide...
Page 58: Figure 16 System Info
Status This field displays Normal for temperatures below the threshold and Error for those above. If Error displays, check that the fans are working and make sure that you do not block ventilation holes on the OMC. OMC-2301 User’s Guide...
Page 59: General Setup
Click Basic Setting > General Setup in the navigation panel to display the screen as shown. Use this screen to configure the system name, the system time and date or set the OMC to save system logs. OMC-2301 User’s Guide...
Page 60: Figure 17 General Setup
Enter the IP address of your timeserver. The OMC searches for the timeserver for Address up to 60 seconds. If you select a timeserver that is unreachable, then this screen will appear locked for 60 seconds. Please wait. OMC-2301 User’s Guide...
Page 61: Ip Setup
192.168.0.1. IP Subnet Enter the IP subnet mask of your OMC in dotted decimal notation for example Mask 255.255.255.0. Default Enter the IP address of the default outgoing gateway in dotted decimal notation, for Gateway example 192.168.1.254 OMC-2301 User’s Guide...
Page 62: Port Setup
Enter a descriptive name (up to nine printable characters and spaces allowed) that identifies this port. Speed/Duplex This field displays 1000M/Full Duplex. Note: The Gigabit Ethernet ports connect at 1000 Mbps only. Connect only Gigabit Ethernet devices to these ports. OMC-2301 User’s Guide...
Page 63: Igmp Snooping
The following figure shows a network example where A is the multicast source while computers 1, 2 and 3 are the receivers. In the figure A is connected to the upstream interface and 1, 2 and 3 are connected to the downstream interface. OMC-2301 User’s Guide...
Page 64: Dba (Dynamic Bandwidth Allocation)
Bandwidth re-assignment can be for an ONU or for the priority-level queues. In addition to reassigning bandwidth on the go, DBA helps to ensure quality of service on the network. A PON port allows only one ONU to transmit data at a time. OMC-2301 User’s Guide...
Page 65: Epon Common Setup
6.8 EPON Common Setup Use the EPON Setup screen to configure general PON (or fiber) interface settings. Click Basic Setting > EPON Common Setup. Figure 21 EPON Setup OMC-2301 User’s Guide...
Page 66: Table 15 Epon Setup
IGMP group without confirmation checks. Upstream Select Pass to forward upstream packets with a matching multicast MAC address in Multicast the range shown. forwarding Select Discard to drop upstream packets with a matching multicast MAC address in the range shown. OMC-2301 User’s Guide...
Page 67: Onu Setup
Clear this check box to disable the profile. ONU Name Enter a descriptive name (up to 20 alpha-numerical characters) to identify the ONU to which this service is applied. Port Select the port to which the ONU is connected. OMC-2301 User’s Guide...
Page 68 Profile a name to configure the 4-port ONU profile. Delete Click Delete to remove the selected entry from the summary table. Note: You cannot delete the default services. Cancel Click Cancel to clear the Delete check boxes. OMC-2301 User’s Guide...
Page 69: Epon Profile
When you create a profile having the same name as an existing profile, the previous settings will be replaced in the existing profile. Current field settings are displayed in bold text labels. Click Basic Setting > EPON Profile to display the configuration screen. OMC-2301 User’s Guide...
Page 70: Figure 23 Epon Profile
The following table describes the labels in this screen. Table 17 EPON Profile LABEL DESCRIPTION Active Select this option to activate this profile. Clear this check box to disable the profile. Name Enter a descriptive name (up to 20 alphanumerical characters) to identify this profile. OMC-2301 User’s Guide...
Page 71 If the downstream traffic flows are assigned different priorities, use Downstream Policing per Queue to make sure packets with a higher priority can be processed first. Active Select Active to control the downstream traffic (from the OLT to the ONU). OMC-2301 User’s Guide...
Page 72 Select this option to enable flow control for the connection to the ONU. Address Learning MAC address learning reduces outgoing broadcast traffic. For MAC address learning to occur on a port, the port itself must be active with address learning enabled. OMC-2301 User’s Guide...
Page 73: Introduction To Vlans
With VLAN, all broadcasts are confined to a specific broadcast domain. VLAN is unidirectional; it only governs outgoing traffic. Chapter 8 on page 83 for information on IEEE 802.1Q tagged VLANs. OMC-2301 User’s Guide...
Page 74: Port-Based Vlans
Your OMC comes with a “Default” profile containing settings that work in most network environment. When you create a profile having the same name as an existing profile, the previous settings will be replaced in the existing profile. Click Basic Setting > 4-Port ONU Profile to display the configuration screen. OMC-2301 User’s Guide...
Page 75: Figure 24 4-Port Onu Profile
This field displays the number of the port on the ONU. Power Down Select this option to disable the connection to the ONU. Auto-negotiation Select this option to establish the connection to the ONU using auto-negotiation for the link speed and duplex mode. OMC-2301 User’s Guide...
Page 76 This field displays the descriptive name of a profile. Active This field displays whether the profile is active or not. Delete Click Delete to remove the selected entry from the summary table. Cancel Click Cancel to clear the Delete check boxes. OMC-2301 User’s Guide...
Page 77: Advanced
Advanced Classifier Filter Profile (79) VLAN Profile (83) Priority Profile (93) Static MAC Forward Setup (97) Destination Filter (101) Port Authentication (105) Access Control (109)
Page 79: Classifier Filter Profile
(tagged or untagged). As the name implies, the “Stop_traffic” filter profile discards all packets, thus preventing the subscriber from sending traffic through the ONU. Click Advanced Application > Classifier Filter Profile to display the configuration screen. Figure 25 Classifier Filter Profile Setup OMC-2301 User’s Guide...
Page 80: Table 19 Classifier Filter Profile Setup
Or select a filter type from the list. Filter Rules Index This field displays the index number. Active Select this option to enable the packet prioritization setting. Direction Select the direction of the traffic to which the setting is applied. OMC-2301 User’s Guide...
Page 81: Example: Classifier Filter Profile
The following example sets the ONU to forwards all untagged packets and drops all tagged packets from the OLT. The ONU drops outgoing packets with VLAN ID 10 to the OLT. Figure 26 Classifier Filter Profile: Example OMC-2301 User’s Guide...
Page 82 Chapter 7 Classifier Filter Profile OMC-2301 User’s Guide...
Page 83: Vlan Profile
VLAN tag or add a new VLAN tag. To forward a frame from an 802.1Q VLAN-unaware device to an 802.1Q VLAN-aware device, the ONU first decides where to forward the frame, and then inserts a VLAN tag reflecting the ingress port's default VID. OMC-2301 User’s Guide...
Page 84: Vlan Stacking
VLANs within its network by adding tag 37 to distinguish customer A and tag 48 to distinguish customer B at edge device 1 and then stripping those tags at edge device 2 as the data frames leave the network. OMC-2301 User’s Guide...
Page 85: Vlan Tag Format
Table 21 Single and Double Tagged 802.11Q Frame Format Len/ Data Untagged Etype Ethernet frame TPID Priority Len/ Data IEEE 802.1Q Etype customer tagged frame DA SA SPTPID Priority VID TPID Priority Len/ Data Double-tagged Etype frame OMC-2301 User’s Guide...
Page 86: Configuring A Vlan Profile
• Set priority No action is done on the OLT which forwards the packets to the destination through the uplink Gigabit Ethernet ports. Click Advanced Applications > VLAN Profile in the navigation panel to display the screen as shown. OMC-2301 User’s Guide...
Page 87: Figure 28 Epon Vlan Profile Setup
Specify the action to perform on the packets. Select Add to insert a VLAN tag to the outgoing packets. Select Exchange to replace the VID with the one specified in the VLAN ID field. Select None to forward packets without any changes. OMC-2301 User’s Guide...
Page 88 If you select IPv4 Protocol in the Classifier field, enter an IPv4 protocol number (1- 255). Refer to Table 26 on page 96 for common protocol numbers. If you select VLAN in the Classifier field, enter a VID (1-4094). OMC-2301 User’s Guide...
Page 89: Vlan Profile: Example
In the following network example, you want to set the ONUs to check VLAN tagged packets to the OLT. If a packet has a VLAN ID of 100, the ONU adds a second tag with VID 200 before transmitting. OMC-2301 User’s Guide...
Page 90: Vlan Profile: Example 2
OLT. If a packet has a VLAN ID of 200, the ONU removes the outer VLAN tag before sending the packet to the computers. The ONU discards all untagged packets. Figure 31 VLAN Network Example 2 100 200 100 200 OMC-2301 User’s Guide...
Page 91: Figure 32 Vlan Profile: Example 2
In the Classifier Filter Profile screen, set the Downstream Default VLAN Filter to discard all untagged packets on the ONU. Figure 33 VLAN Profile: Example 2: Classifier Filter Profile In the ONU Setup screen, apply the configured classifier filter profile and VLAN profile to the ONU. OMC-2301 User’s Guide...
Page 92 Chapter 8 VLAN Profile OMC-2301 User’s Guide...
Page 93: Priority Profile
Click Advanced Application > Priority Profile to display the configuration screen. Use this screen to change the precedence bits (TOS-COS mappings) and VLAN priority and assign specified packets to queues. Once you have configured a priority profile, associate it to a service profile to apply to an ONU. OMC-2301 User’s Guide...
Page 94: Figure 34 Priority Profile
Select a COS level for the corresponding TOS number. The ONU adds the COS number to the packets. Use the EPON Common Setup screen to map the COS levels to the queues. Index This field displays the index number. OMC-2301 User’s Guide...
Page 95: Table 25 Common Ethernet Types Numbers
The following table shows some common Ethernet types and the corresponding hexadecimal number. Table 25 Common Ethernet Types Numbers ETHERNET TYPE NUMBER IP ETHII 0800 X.75 Internet 0801 NBS Internet 0802 ECMA Internet 0803 Chaosnet 0804 X.25 Level 3 0805 XNS Compat 0807 Banyan Systems 0BAD OMC-2301 User’s Guide...
Page 96: Example: Priority Profile
VLAN group. The AppleTalk packets are sent out through queue 3. Thus AppleTalk packets in a VLAN group have the highest priority and get sent first. The following figure shows the example configuration. Figure 35 Priority Profile: Example OMC-2301 User’s Guide...
Page 97: Static Mac Forward Setup
Static MAC Forwarding Status screen. Click Advanced Application > Static MAC Forwarding. Figure 36 Static MAC Forwarding Status The following table describes the labels in this screen. Table 27 Static MAC Forwarding Status LABEL DESCRIPTION Port No This field displays the port index number. OMC-2301 User’s Guide...
Page 98: Configuring Static Mac Forwarding
(No). You may temporarily deactivate a rule without deleting it. Name This field displays the descriptive name for this rule. ONU Name This field displays the name of the ONU to which this rule is applied. OMC-2301 User’s Guide...
Page 99 This field displays the MAC address of the packets that will be forwarded. Delete Select the entry(ies) that you want to remove in the Delete column and then click the Delete button. Cancel Click Cancel to clear the Delete check boxes. OMC-2301 User’s Guide...
Page 100 Chapter 10 Static MAC Forward Setup OMC-2301 User’s Guide...
Page 101: Destination Filter
This field displays the port index number. Number of This field displays the number of destination filters you have configured for this port. Destination Filter Destination Click the link to display a screen where you can configure a destination filter. Filter OMC-2301 User’s Guide...
Page 102: Destination Filter Setup
This field displays the descriptive name for this rule. This is for identification purpose only. ONU Name This field displays the name of the ONU to which this rule is applied. This field displays the MAC address of the packets that will be filtered. Address OMC-2301 User’s Guide...
Page 103: Example: Destination Filter
Click Cancel to clear the selected checkbox(es) in the Delete column. 11.3.1 Example: Destination Filter The following example sets the OLT to block packets with a destination MAC address of 00:00:00:00:a0:5f to the ONU named CA1101. Figure 40 Destination Filter: Example OMC-2301 User’s Guide...
Page 104 Chapter 11 Destination Filter OMC-2301 User’s Guide...
Page 105: Port Authentication
In essence, RADIUS authentication allows you to validate an unlimited number of users from a central location. On the OMC-2301, you MUST connect the RADIUS server to the MGMT port. Figure 41 RADIUS Server Network Example RADIUS Server At the time of writing, only Windows XP of the Microsoft operating systems supports it.
Page 106: Configuring Port Authentication
Figure 42 Port Authentication 12.2.1 Activating IEEE 802.1x Security Enable and configure IEEE 802.1x security settings in the 802.1x screen. From the Port Authentication screen, display the configuration screen as shown. Figure 43 Port Authentication: 802.1x OMC-2301 User’s Guide...
Page 107: Configuring Radius Server Settings
Figure 44 Port Authentication: RADIUS The following table describes the labels in this screen. Table 32 Port Authentication: RADIUS LABEL DESCRIPTION Authentication Server IP Address Enter the IP address of the external RADIUS server in dotted decimal notation. OMC-2301 User’s Guide...
Page 108 RADIUS server and the OMC. This key is not sent over the network. This key must be the same on the external RADIUS server and the OMC. Apply Click Apply to save your changes back to the OMC. Cancel Click Cancel to begin configuring this screen afresh. OMC-2301 User’s Guide...
Page 109: Access Control
Connection to host lost. C:\> Section 19.2.1 on page 146 for more information on disabling multi-login. 13.2 The Access Control Main Screen Click Advanced Application > Access Control in the navigation panel to display the main screen as shown. OMC-2301 User’s Guide...
Page 110: About Snmp
Examples of variables include such as number of packets received, node port status etc. A Management Information Base (MIB) is a collection of managed objects. SNMP allows a manager and agents to communicate for the purpose of accessing these objects. OMC-2301 User’s Guide...
Page 111: Supported Mibs
1.3.6.1.6.3.1.1.5. This trap is sent when the Ethernet link is down. linkUp 1.3.6.1.6.3.1.1.5. This trap is sent when the Ethernet link is up. authenticationFailure 1.3.6.1.6.3.1.1.5. This trap is sent when an SNMP request comes from non-authenticated hosts. OMC-2301 User’s Guide...
Page 112: Configuring Snmp
• A non-administrator (username is something other than admin) is someone who can view but not configure OMC settings. It is highly recommended that you change the default administrator password (1234). Click Access Control from the navigation panel and then click Logins from this screen. OMC-2301 User’s Guide...
Page 113: Ssh Overview
13.5 SSH Overview Unlike Telnet or FTP, which transmit data in clear text, SSH (Secure Shell) is a secure communication protocol that combines authentication and data encryption to provide secure encrypted communication between two hosts over an unsecured network. OMC-2301 User’s Guide...
Page 114: How Ssh Works
After the identification is verified and data encryption activated, a secure tunnel is established between the client and the server. The client then sends its authentication information (user name and password) to the server to log in to the server. OMC-2301 User’s Guide...
Page 115: Ssh Implementation On The Omc
1 HTTPS connection requests from an SSL-aware web browser go to port 443 (by default) on the OMC’s WS (web server). 2 HTTP connection requests from a web browser go to port 80 (by default) on the OMC’s WS (web server). Figure 51 HTTPS Implementation OMC-2301 User’s Guide...
Page 116: Https Example
OMC. If Accept this certificate temporarily for this session is selected, then click OK to continue in Netscape. Select Accept this certificate permanently to import the OMC’s certificate into the SSL client. OMC-2301 User’s Guide...
Page 117: The Main Screen
13.9.3 The Main Screen After you accept the certificate and enter the login username and password, the OMC main screen appears. The lock displayed in the bottom right of the browser status bar denotes a secure connection. OMC-2301 User’s Guide...
Page 118: Service Access Control
The following table describes the fields in this screen. Table 38 Access Control: Service Access Control LABEL DESCRIPTION Access Click the Access Control link to return to the main screen. Control Services Services you may use to access the OMC are listed here. OMC-2301 User’s Guide...
Page 119: Remote Management
The OMC immediately disconnects the session if it does not match. Telnet/FTP/ Select the service(s) that may be used for managing the OMC from the specified HTTP/ICMP/ trusted computers. SNMP/SSH/ HTTPS OMC-2301 User’s Guide...
Page 120 Chapter 13 Access Control Table 39 Access Control: Remote Management (continued) LABEL DESCRIPTION Apply Click Apply to save your changes back to the OMC. Cancel Click Cancel to begin configuring this screen afresh. OMC-2301 User’s Guide...
Page 121: Management
Management Maintenance (123) Diagnostic (131) Syslog (133) MAC Table (137) IGMP Table (141)
Page 123: Maintenance
1 From the Maintenance screen, click the Click Here button next to Load Factory Defaults to clear all OMC configuration information you configured and return to the factory defaults. The following message appears. Figure 59 Load Factory Default: Conformation OMC-2301 User’s Guide...
Page 124: Reboot System
ONUs every time you upgrade the firmware on the OMC. Follow the steps below to perform remote firmware upgrade on an ONU connected to the OMC. 1 Click Management > Maintenance to access the Remote Firmware Upgrade screen. Figure 61 Maintenance: Remote Firmware Upgrade OMC-2301 User’s Guide...
Page 125: Line Card Reset
Figure 62 Maintenance: Line Card Reset 2 Select the line card(s) you want to reset in the list box. You can select multiple entries by holding down the [SHIFT] or [CTRL] key. 3 Click Reset to reset the selected card(s). OMC-2301 User’s Guide...
Page 126: Onu Device Reset
Be sure to upload the correct model firmware as uploading the wrong model firmware may damage your device. From the Maintenance screen, display the Firmware Upgrade screen as shown next. OMC-2301 User’s Guide...
Page 127: Restore Configuration
Backing up your OMC configurations allows you to create various “snap shots” of your device from which you may restore at a later date. Back up your current OMC configuration to a computer using the Backup Configuration screen. OMC-2301 User’s Guide...
Page 128: Ftp Command Line
This is a sample FTP session showing the transfer of the computer file "firmware.bin" to the OMC. ftp> get config config.cfg This is a sample FTP session saving the current configuration to a file called “config.cfg” on your computer. OMC-2301 User’s Guide...
Page 129: Ftp Command Line Procedure
Transfer files in either ASCII (plain text format) or in binary mode. Configuration and firmware files should be transferred in binary mode. Initial Remote Specify the default remote directory (path). Directory Initial Local Directory Specify the default local directory (path). OMC-2301 User’s Guide...
Page 130: Ftp Restrictions
• FTP service is disabled in the Access Control screen. • The IP address(es) in the Secured Client Set in the Remote Management screen does not match the client IP address. If it does not match, the OMC will disconnect the Telnet session immediately. OMC-2301 User’s Guide...
Page 131: Diagnostic
Click Prev 50 to display the previous 50 logs. Click Display to display a log of events in the multi-line text box. Click Next 50 to display the next 50 logs. Click Clear to empty the text box and erase the logs. OMC-2301 User’s Guide...
Page 132: Saving Logs
Once the number is reached, the OMC wraps around and deletes the old logs. • To save logs on an external syslog server, configure the Syslog Server Setup screen (refer Section 16.2 on page 133). Make sure the syslog server is connected to the MGMT port on the OMC. OMC-2301 User’s Guide...
Page 133: Syslog
On the OMC, make sure the external syslog server is connected to the MGMT port. Click Management > Syslog in the navigation panel to display this screen. The syslog feature sends logs to an external syslog server. Use this screen to configure the device’s system logging settings. OMC-2301 User’s Guide...
Page 134: Syslog Server Setup
Click Cancel to begin configuring this screen afresh. 16.3 Syslog Server Setup Click Management > Syslog and click the Syslog Server Setup link to open the following screen. Use this screen to configure a list of external syslog servers. Figure 69 Syslog: Server Setup OMC-2301 User’s Guide...
Page 135: Table 44 Syslog: Server Setup
This field displays the severity level of the logs that the device is to send to this syslog server. Delete Select an entry’s Delete check box and click Delete to remove the entry. Cancel Click Cancel to begin configuring this screen afresh. OMC-2301 User’s Guide...
Page 136 Chapter 16 Syslog OMC-2301 User’s Guide...
Page 137: Mac Table
If peer-to-peer communication is disabled, the frame is sent to the uplink ports. • If the OMC has already learned the LLID for this MAC address, but the destination LLID is the same as the source LLID, then it filters the frame. OMC-2301 User’s Guide...
Page 138: Viewing The Mac Table
OMC. The MAC address of the connected ONU is not erased from the MAC table. Index This is the incoming frame index number. MAC Address This is the MAC address of the device from which this incoming frame came. OMC-2301 User’s Guide...
Page 139 DESCRIPTION LLID This is the link ID to which the MAC address is associated. Type This shows whether the MAC address is dynamic (learned by the OMC) or static (manually entered in the Static MAC Forwarding screen). OMC-2301 User’s Guide...
Page 140 Chapter 17 MAC Table OMC-2301 User’s Guide...
Page 141: Igmp Table
This field displays IGMP group address. Destination Address This field displays the number of the VLAN on which the subscriber sends IGMP query messages. Members This field displays the LLID(s) that is a member of the group. (LLID) OMC-2301 User’s Guide...
Page 142 Chapter 18 IGMP Table OMC-2301 User’s Guide...
Page 143: Commands, Troubleshooting And Specifications
Commands, Troubleshooting and Specifications Introducing the Commands (145) Command Examples (175) Troubleshooting (191) Product Specifications (203)
Page 145: Introducing The Commands
You may also edit a configuration file using a text editor. Make sure you use valid commands. The OMC rejects configuration files with invalid or incomplete commands. 19.2 Accessing the CLI You can use a direct console connection or Telnet to access the CLI on the OMC. OMC-2301 User’s Guide...
Page 146: Multiple Login
You can view the initialization information using the console port. After the initialization, the login screen displays (refer to Section 19.3 on page 148). opyright (c) 1995 - 2006 ZyXEL Communications Corp. initialize mgmt, ethernet address: 00:09:41:01:23:45 Initializing VLAN Database... Initializing IP Interface...
Page 147: Telnet
X11 forwarding re-enabled. Host key saved to C:/Documents and Settings/user/Application Data/SSH/ hostkeys/key_22_192.168.0.1.pub host key for 192.168.0.1, accepted by user Thu Jul 20 2006 01:16:58 admin's password: Authentication successful. Copyright (c) 1994 - 2006 ZyXEL Communications Corp. sysname> OMC-2301 User’s Guide...
Page 148: The Login Screen
(CLI) and Enable and Config modes of the CLI. The password you change with this command is required to enter Enable and Config modes of the CLI. Syntax: password <password> OMC-2301 User’s Guide...
Page 149: Command Modes
To enter the vlan-profile mode, enter vlan-profile followed by a descriptive name for the profile. vlan-profile Example For example, enter to create a new Example profile and enter sub configuration mode. OMC-2301 User’s Guide...
Page 150: Getting Help
<port-number> <llid> show epon-counter onu <port-number> <llid> mac-flush <cr> mac-flush <port-num> ping <ip|host-name> <cr> ping <ip|host-name> [..] ping help traceroute <ip|host-name> <cr> traceroute <ip|host-name> [..] traceroute help ssh <1|2> <[user@]dest-ip> <cr> ssh <1|2> <[user@]dest-ip> [command </>] sysname> OMC-2301 User’s Guide...
Page 151: Detailed Command Information
( ) or down ( ) arrow key to scroll through the previously used commands and press [ENTER]. Use the history command to display the list of commands. sysname> history enable exit history sysname> OMC-2301 User’s Guide...
Page 152: Saving Your Configuration
Logs out from the CLI. exit Displays help information. help Displays a list of previously command(s) that you have history executed. The OMC stores up to 256 commands in history. Exits from the CLI. logout Clears the MAC address table. mac-flush OMC-2301 User’s Guide...
Page 153 1402. The digit(s) before 0 in a port number corresponds to the card slot on the OLT, and the last digit denotes the port type (1 for PON port and 2 for uplink port). Displays the IGMP table for the specified logical link. <port-number> <llid> OMC-2301 User’s Guide...
Page 154 1402. The digit(s) before 0 in a port number corresponds to the card slot on the OLT, and the last digit denotes the port type (1 for PON port and 2 for uplink port). Displays the connection status of all Gigabit Ethernet status ports. OMC-2301 User’s Guide...
Page 155: Enable Mode
Restore a previous backup configuration tftp config <index> file to the device. The device will not use <ip> <remote- the restored configuration until the next file> restart. Restores a previous backup flash <ip> configuration file to the running <remote-file> configuration. OMC-2301 User’s Guide...
Page 156 Displays classifier filter profile summary show classifier-filter- table. profile Displays detailed settings of the specified <profile-name> classifier filter profile. Displays current DBA (Dynamic dba-mode Bandwidth Allocation) method the device uses. Displays the status of all PON ports. epon OMC-2301 User’s Guide...
Page 157 Displays port IGMP member information. <port-number> Displays LLID IGMP member <port-number> information. <llid> Displays the IP settings. Displays system logs. logging Displays MAC address table on the PON mac-address <port-number> port. Displays MAC address table on the <port-number> logical link. llid OMC-2301 User’s Guide...
Page 158 Displays port settings for all Gigabit uplink Ethernet ports. Displays port settings for the specified <port-number> Gigabit Ethernet port. Displays the onnection status of all status Gigabit Ethernet ports. Displays login account information. user Displays multi-login status. user-session OMC-2301 User’s Guide...
Page 159: General Configuration Mode
<name> onu <onu- specified destination MAC name> mac <mac-addr> address. action <discard|pass> Disables a destination filter. inactive Configures a static MAC epon-mac-forward port <port-number> address forwarding rule. name <name> onu <onu- name> mac <mac-addr> OMC-2301 User’s Guide...
Page 160 <port-number> forwarding. name <name> onu <onu-name> mac <mac-addr> Disables an EPON profile. epon-profile <name> Resets the session timeout to https timeout the default of 300 seconds. Disables the IP interface. Disables log saving. log periodical-save OMC-2301 User’s Guide...
Page 161 Removes remote known hosts known-hosts <host- with the specified public key ip> [1024|ssh- (1024-bit RSA1, RSA or DSA). rsa|ssh-dsa] Disables syslog logging. syslog Disables syslog logging to the server <ip- specified syslog server. address> OMC-2301 User’s Guide...
Page 162 Specifies the time the OMC supplicant-timeout waits for a response. <1-255> Specifies the time the OMC transmission- waits for a response from a period <1-255> client before sending the request to the authentication server. OMC-2301 User’s Guide...
Page 163 Sets the trap community. trap-community <property> Sets the IP addresses of up to trap-destination <ip> four stations to send your SNMP traps to. Adds a remote host to which known-hosts <host-ip> the OMC can access using <1024|ssh-rsa|ssh-dsa> SSH service. <key> OMC-2301 User’s Guide...
Page 164 Configures up to four read-only user username <name> login accounts. password <pwd> Enables multi-login. user-session Enters the VLAN profile vlan-profile <name> configuration mode. See Section 19.10.10 on page 171 for the available commands. OMC-2301 User’s Guide...
Page 165: Classifier-Filter-Profile Commands
Sets the action for upstream upstream-def-vlan- tag-frame tagged frames. filter <discard|pass> Sets the action for upstream untag-frame untagged frames. <discard|pass> Sets the action for the Ethernet upstream-rule <1-8> action type classifier rule. <table1|table2> <discard|pass> <1-8> : Classifier rule index. OMC-2301 User’s Guide...
Page 166: Epon-Common Commands
<0-7> downstream traffic. Exits from the epon-common mode. Exits from the configuration exit mode. Enables group leave igmp-last-member confirmation checks. Enables IGMP proxy. igmp-proxy Enables IGMP snooping. igmp-snooping Sets learned MAC aging time. mac-aging-time <10- 86400> OMC-2301 User’s Guide...
Page 167: Epon-Onu4-Profile Commands
Disables flow control for the onu-phy port <1- connection to the specified port on the 4> flow-control ONU. Enables the connection to the onu-phy port <1- specified port on the ONU. 4> power-down Disables port-based VLAN on the port-based-vlan ONU. <cr> OMC-2301 User’s Guide...
Page 168: Epon-Profile Commands
COMMAND DESCRIPTION Sets a descriptive name for the profile epon-profile and enters the epon-profile mode. <name> Enables this profile. active Enables MAC address learning for this address-learning profile. Sets the number of MAC address address-limit <0-64> allowed. OMC-2301 User’s Guide...
Page 169 Disables auto-negotiation on the PON onu-phy auto- port. negotiation Disables flow control for the onu-phy flow- connection to the ONU. control Enables the connection to the ONU. onu-phy power- down Disables upstream priority queuing. up-queue Disables upstream queue policing. up-queue- policing OMC-2301 User’s Guide...
Page 170: Onu Commands
Sets the MAC address of the onu-mac <mac-addr> ONU to which the service profile is applied. Sets the priority profile for this priority-profile service. <profile-name> Sets the VLAN profile for this vlan-profile <profile- service. name> OMC-2301 User’s Guide...
Page 171: Priority-Profile Commands
Specifies the outgoing queue queue <0-3> for the prioritized traffic. Disables the priority profile. no active Sets the TOS-to-COS mapping. tos-to-cos tos <0-7> cos <0-7> 19.10.10 vlan-profile Commands The following table lists the commands in configuration mode. vlan-profile OMC-2301 User’s Guide...
Page 172: Table 57 Vlan-Profile Commands
<original|priority- profile setting. profile> Sets the rule type. type <ethertype|ipv4|vlan> Specifies the Ethernet type or protocol value number for the rule. ethertype:<0x0000- 0xFF0F>|ipv4:<1- 255>|vlan:<1-4094> Sets the VLAN type for the rule. vlan-type <8100|9100|88A8> OMC-2301 User’s Guide...
Page 173 Chapter 19 Introducing the Commands Table 57 vlan-profile Commands (continued) COMMAND DESCRIPTION Sets the default rule settings for upstream-def-rule action <add|exchange> upstream traffic. vlan-type <8100|9100|88A8> vid <1-4094> priority-src <original|priority- profile> Clears the default rule settings for action none upstream traffic. OMC-2301 User’s Guide...
Page 174 Chapter 19 Introducing the Commands OMC-2301 User’s Guide...
Page 175: Command Examples
The following example shows the status on all PON ports. sysname# show epon Epon Port LLID Total Status Down Down Down Down Down Down Down Down 1001 Down 1101 Down 1201 Down 1301 Down 1401 Down 1501 Down 1601 Down sysname# OMC-2301 User’s Guide...
Page 176: Show Epon-Counter
This command displays the port statistics on the OMC. The following example shows the port statistics on PON port 801. sysname# show epon-counter 801 PON Octets: Tx OK = 396963168 Rx OK = 225300422 PON Frames: Rx OK = 24993 Rx HEC Error sysname# OMC-2301 User’s Guide...
Page 177: Show Epon-Counter Onu
Rx OK Rx Err sysname# 20.2.4 show hardware-monitor Syntax: system hardware-monitor <C|F> This command displays the device temperature and voltage readings and fan speeds. You can choose to display the temperature in Celsius ( ) or Fahrenheit ( OMC-2301 User’s Guide...
Page 178: Show Ip
This command displays the IP related information (such as IP address and subnet mask) on all OMC interfaces. The following figure shows the default interface settings. sysname> show ip Out-of-band Management IP Address IP[192.168.0.1], Netmask[255.255.255.0], Default Gateway[0.0.0.0] sysname> 20.2.6 show system-information Syntax: show system-information OMC-2301 User’s Guide...
Page 179: Ip Address
• Saves current configuration to the configuration file the OMC is currently using. sysname(config)# ip address 172.23.37.206 255.255.255.0 sysname(config)# ip address default-gateway 172.23.37.254 sysname(config)# end sysname# write memory sysname# 20.4 ping Syntax: ping <ip|host-name> [size <0-1472>] [-t] OMC-2301 User’s Guide...
Page 180: Traceroute
192.168.0.100 traceroute to 192.168.0.100, 30 hops max, 40 byte packet 1:192.168.0.100 (10 ms) (10 ms) (0 ms) traceroute done: sysname> 20.6 epon-common Commands This section shows you how to configure common EPON settings in configuration mode. OMC-2301 User’s Guide...
Page 181: Epon-Profile Commands
<name> dba priority-class <0-7> epon-profile <name> dn-policing epon-profile <name> dn-policing max-burst <0-8191> epon-profile <name> dn-policing max-dn-bw <0-16000> epon-profile <name> encryption-mode <both|downstream> where Specifies the name of the profile. <name> Enables MAC address learning for this profile. address- learning OMC-2301 User’s Guide...
Page 182 • Create an EPON profile called plan2dn • The policy applies to the downstream traffic. • Enable data encryption on both the upstream and downstream traffic. • Set the minimum and maximum upstream bandwidth to 2000 and 30000 respectively. OMC-2301 User’s Guide...
Page 183: Configuration File Maintenance
Use the boot config command to restart the OMC and use a different configuration file (if specified). The following example reboots the switch to use the second configuration file. Figure 73 boot config Command Example sysname# boot config 2 OMC-2301 User’s Guide...
Page 184: Restoring Configuration
2 Enter to save the changes to the current configuration file. write memory The following example resets both configuration files to the factory default settings. sysname# erase running-config sysname# write memory OMC-2301 User’s Guide...
Page 185: No Command Examples
Remove remote known hosts with a specified public key known-hosts <host-ip> [1024|ssh-rsa|ssh-dsa] (1024-bit RSA1, RSA or DSA). An example is shown next. • Disable the secure shell RSA1 encryption key. • Remove the remote host with IP address 172.165.1.8 from the list of known hosts. OMC-2301 User’s Guide...
Page 186: Priority-Profile Commands
Enter a number between 0 and 7. The bigger the number, the higher the priority. = Sets the TOS-COS mapping. tos-to-cos tos <0-7> cos <0-7> Use these commands to create and configure a priority profile. OMC-2301 User’s Guide...
Page 187: Onu Commands
EPON profile, the default profile applies. = Specifies the MAC address of an ONU to which this onu-mac <mac-addr> profile is applied. Make sure the ONU is connected to the specified port. OMC-2301 User’s Guide...
Page 188: Vlan-Profile Commands
<name> downstream rule <1-7> priority-src <original| priority- profile> vlan-profile <name> downstream rule <1-7> type <ethertype| ipv4| vlan> vlan-profile <name> downstream rule <1-7> value ethertype:<0x0000- 0xFF0F>|ipv4<1-255>|vid <1-4094>> vlan-profile <name> downstream-def-rule action <delete|exchange> vid <1-4094> priority-src <original| priority-profile> vlan-profile <name> downstream-def-rule action none OMC-2301 User’s Guide...
Page 189 VProfile sysname(config-vlan-profile)# active sysname(config-vlan-profile)# downstream rule 1 active sysname(config-vlan-profile)# downstream rule 1 type vlan sysname(config-vlan-profile)# downstream rule 1 value 14 sysname(config-vlan-profile)# downstream rule 1 new-vid 14 sysname(config-vlan-profile)# downstream rule 1 action delete sysname(config-vlan-profile)# OMC-2301 User’s Guide...
Page 190 Chapter 20 Command Examples OMC-2301 User’s Guide...
Page 191: Troubleshooting
(see the OLT-2300’s User’s Guide for directions). One of the LEDs does not behave as expected. 1 Make sure you understand the normal behavior of the LED. See Section 2.2 on page OMC-2301 User’s Guide...
Page 192: Omc Access And Login
5 Reset the device to its factory defaults, and try to access the OMC with the default IP address. See Section 21.5 on page 195. 6 If the problem continues, contact the network administrator or vendor, or try the following. OMC-2301 User’s Guide...
Page 193 (or a total of four Telnet and SSH sessions with multiple login enabled). 2 Make sure that your computer’s IP address matches a configured secured client IP address (if configured). The OMC immediately disconnects the telnet session if secured OMC-2301 User’s Guide...
Page 194: Management Lockout
1 The OMC can automatically restart a line card that it is managing. If the line card is unresponsive, use the line-card-reset command to perform a hardware reset on the line card. 2 Try removing the line card from the slot and re-installing it. OMC-2301 User’s Guide...
Page 195: Resetting The Defaults
4 Type atlc after the “Enter Debug Mode” message. 5 Wait for the “Starting XMODEM upload” message before activating XMODEM upload on your terminal. 6 After a successful configuration file upload, type atgo to restart the OMC. OMC-2301 User’s Guide...
Page 196: Recovering The Firmware
4 When you see the Press any key to enter Debug Mode within 3 seconds message press a key to enter debug mode. 5 Type after the message (this changes the console port atba5 Enter Debug Mode speed to 115200 bps). OMC-2301 User’s Guide...
Page 197: Pop-Up Windows, Javascripts And Java Permissions
Either disable pop-up blocking (enabled by default in Windows XP SP (Service Pack) 2) or allow pop-up blocking and create an exception for your device’s IP address. 21.6.1.1 Disable pop-up Blockers 1 In Internet Explorer, select Tools, Pop-up Blocker and then select Turn Off Pop-up Blocker. OMC-2301 User’s Guide...
Page 198: Figure 77 Pop-Up Blocker
Alternatively, if you only want to allow pop-up windows from your device, see the following steps. 1 In Internet Explorer, select Tools, Internet Options and then the Privacy tab. 2 Select Settings…to open the Pop-up Blocker Settings screen. OMC-2301 User’s Guide...
Page 199: Figure 79 Internet Options
3 Type the IP address of your device (the web page that you do not want to have blocked) with the prefix “http://”. For example, http://192.168.1.1. 4 Click Add to move the IP address to the list of Allowed sites. Figure 80 Pop-up Blocker Settings OMC-2301 User’s Guide...
Page 200: Javascripts
3 Scroll down to Scripting. 4 Under Active scripting make sure that Enable is selected (the default). 5 Under Scripting of Java applets make sure that Enable is selected (the default). 6 Click OK to close the window. OMC-2301 User’s Guide...
Page 201: Java Permissions
1 From Internet Explorer, click Tools, Internet Options and then the Security tab. 2 Click the Custom Level... button. 3 Scroll down to Microsoft VM. 4 Under Java permissions make sure that a safety level is selected. 5 Click OK to close the window. OMC-2301 User’s Guide...
Page 202: Figure 83 Security Settings - Java
1 From Internet Explorer, click Tools, Internet Options and then the Advanced tab. 2 make sure that Use Java 2 for <applet> under Java (Sun) is selected. 3 Click OK to close the window. Figure 84 Java (Sun) OMC-2301 User’s Guide...
Page 203: Product Specifications
H A P T E R Product Specifications This appendix gives details about the OLT-2300 default settings and OMC-2301 hardware and features. OLT-2300 Default Settings This table lists major default settings. Table 58 Default Settings Default Out-of-band IP 192.168.0.1 Address Default Out-of-band 255.255.255.0 (24 bits)
Page 204: Table 60 Olt-2300 Features
Chapter 22 Product Specifications Table 59 OMC-2301 Specifications (continued) Standards PON : IEEE802.3ah Compliance Ethernet : IEEE802.3ab SNMP : RFC1157 V1.0 MIBs : RFC1155, RFC2578, RFC1212 Safety IEC60950-1 (no CB report) EN 60950-1 for Europe UL 60950-1 for USA CSA No. 22.2 Std. 60950-1 for Canada Compliant to Class 1 for laser safety according to IEC 825-2.
Page 205: Figure 85 Console Cable Rj-11 Male Connector
User's Guide. Console Cable Pin Assignments The following diagrams and chart show the pin assignments of the console cable. Figure 85 Console Cable RJ-11 Male Connector OMC-2301 User’s Guide...
Page 206: Figure 86 Console Cable Db-9 Female Connector
Chapter 22 Product Specifications Figure 86 Console Cable DB-9 Female Connector Table 61 Console Cable Connector Pin Assignments RJ-11 MALE DB-9 FEMALE Pin 2: TXD Pin 2 Pin 3: RXD Pin 3 Pin 4: GND Pin 5 OMC-2301 User’s Guide...
Page 207: Appendix And Index
Appendix and Index The appendices provide general information. Some details may not apply to your OMC. Legal Information (209) Customer Support (213) Index (219)
Page 210 ZyXEL will, at its discretion, repair or replace the defective products or components without charge for either parts or labor, and to whatever extent it shall deem necessary to restore the product or components to proper operating OMC-2301 User’s Guide...
Page 211 Registration Register your product online to receive e-mail notices of firmware upgrades and information at www.zyxel.com for global products, or at www.us.zyxel.com for North American products. OMC-2301 User’s Guide...
Page 212 Appendix A Legal Information OMC-2301 User’s Guide...
Page 213: Appendix B Customer Support
• Sales E-mail: sales@zyxel.com.tw • Telephone: +886-3-578-3942 • Fax: +886-3-578-2439 • Web: www.zyxel.com, www.europe.zyxel.com • FTP: ftp.zyxel.com, ftp.europe.zyxel.com • Regular Mail: ZyXEL Communications Corp., 6 Innovation Road II, Science Park, Hsinchu 300, Taiwan Costa Rica • Support E-mail: soporte@zyxel.co.cr • Sales E-mail: sales@zyxel.co.cr •...
Page 214 Appendix B Customer Support • Regular Mail: ZyXEL Communications, Czech s.r.o., Modranská 621, 143 01 Praha 4 - Modrany, Ceská Republika Denmark • Support E-mail: support@zyxel.dk • Sales E-mail: sales@zyxel.dk • Telephone: +45-39-55-07-00 • Fax: +45-39-55-07-07 • Web: www.zyxel.dk • Regular Mail: ZyXEL Communications A/S, Columbusvej, 2860 Soeborg, Denmark Finland •...
Page 215 • Regular Mail: ZyXEL Malaysia Sdn Bhd., 1-02 & 1-03, Jalan Kenari 17F, Bandar Puchong Jaya, 47100 Puchong, Selangor Darul Ehsan, Malaysia North America • Support E-mail: support@zyxel.com • Support Telephone: +1-800-978-7222 • Sales E-mail: sales@zyxel.com • Sales Telephone: +1-714-632-0882 • Fax: +1-714-632-0858 • Web: www.zyxel.com OMC-2301 User’s Guide...
Page 216 Appendix B Customer Support • Regular Mail: ZyXEL Communications Inc., 1130 N. Miller St., Anaheim, CA 92806- 2001, U.S.A. Norway • Support E-mail: support@zyxel.no • Sales E-mail: sales@zyxel.no • Telephone: +47-22-80-61-80 • Fax: +47-22-80-61-81 • Web: www.zyxel.no • Regular Mail: ZyXEL Communications A/S, Nils Hansens vei 13, 0667 Oslo, Norway Poland •...
Page 217 • Sales E-mail: sales@zyxel.co.uk • Telephone: +44-1344-303044, 08707-555779 (UK only) • Fax: +44-1344-303034 • Web: www.zyxel.co.uk • FTP: ftp.zyxel.co.uk • Regular Mail: ZyXEL Communications UK Ltd., 11 The Courtyard, Eastern Road, Bracknell, Berkshire RG12 2XB, United Kingdom (UK) OMC-2301 User’s Guide...
Page 218 Appendix B Customer Support OMC-2301 User’s Guide...
Page 219: Index
CI Commands default settings Class of Service See CoS default user name classification filter profile destination filter action on matched packets access priority example change password setup login password detailed fiber port status OMC-2301 User’s Guide...
Page 220 Fiber To The Building IEEE 802.3x FTTB IGMP Fiber To The Home proxy See also FTTH IGMP snooping File Transfer Protocol See also FTP IGMP snooping table filename convention IGMP statistics filter IGMP table filtering database IGMP version OMC-2301 User’s Guide...
Page 221 IP address quiet period management interface server timeout setup procedure management IP address supplicant timeout management IP setting transmission period managing the device port connection good habits port duplex mode using FTP. See FTP. port setup OMC-2301 User’s Guide...
Page 222 38, 47, 57 remote device reset EPON details remote management EPON info service remote ONU firmware upgrade port reset the device 41, 123 port details reset to factory default settings switch lockout resetting ONU syntax conventions OMC-2301 User’s Guide...
Page 223 TOS-COS mapping trademarks trap destination XMODEM upload 195, 197 Universal Time Coordinated See also UTC update firmware ZyNOS (ZyXEL Network Operating System) USER Telco-50 Connectors view system log Virtual Local Area Network See VLAN VLAN double tagging OMC-2301 User’s Guide...
Page 224 Index OMC-2301 User’s Guide...

ZyXEL Communications OMC-2301 User Manual

Chapter 1 Introducing the OMC

Chapter 2 Hardware

Chapter 3 The Web Configurator

Chapter 4 Initial Setup Example

Chapter 5 System Status and Port Statistics

Chapter 6 Basic Setting

Chapter 7 Classifier Filter Profile

Chapter 8 VLAN Profile

Chapter 9 Priority Profile

Chapter 10 Static MAC Forward Setup

Chapter 11 Destination Filter

Chapter 12 Port Authentication

Chapter 13 Access Control

Chapter 14 Maintenance

Chapter 15 Diagnostic

Chapter 16 Syslog

Chapter 17 MAC Table

Chapter 18 IGMP Table

Chapter 19 Introducing the Commands

Quick Links

Troubleshooting

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for ZyXEL Communications OMC-2301

Summary of Contents for ZyXEL Communications OMC-2301