Table of Contents
Advertisement
The POWER button is normally left in the on position. Always turn the power
off during cleaning or servicing the fan and during thunderstorms. It is also used
to exit or enter additional programs.
POWER must be left on to retain a previously set fan speed or light level.
There are six individual speed settings for the fan; each speed is indicated by an
audible tone of increasing pitch.
To select the desired fan speed:
1. With fan off, press and hold the button labeled FAN. The fan blades will start
rotating at the slowest speed, and will increase in steps.
2. Release the button when the desired speed is reached.
The fan speed is now in memory and will automatically come on at the same
speed each time the F F F F F AN
AN
AN
AN button is used. To maintain this level of speed, turn the
AN
fan on by pressing F F F F F AN
AN
AN
AN less than one second. To lower speed, turn fan off, then
AN
on by pressing and holding the F F F F F AN
When the fan is on, you may increase the speed by pressing and holding the
F F F F F AN
AN
AN
AN
AN button until the desired speed is reached, then release it.
The direction of airflow can be changed from downward
to upward or from upward to downward.
To reverse the airflow:
1. Make sure the F F F F F AN
AN
AN
AN is on.
AN
2. Press the R R R R R E E E E E VE
VER R R R R SE
VE
VE
SE button.
SE
SE
VE
SE
To turn the lights off and on, press and release the L L L L L IGH
one second.
To vary the light brightness:
1. With lights off, press and hold the LIGHT button. After one second the lights
come on at their lowest level and gradually become brighter.
2. Release the LIGHT button when the desired brightness level is reached.
The brightness level is now in the fan memory and will automatically come on at
the same brightness the next time the L L L L L IGH
level of brightness, press the L L L L L IGH
IGHT T T T T button for less than one second. To lower the
IGH
IGH
IGH
brightness, turn the lights off, then press and hold the L L L L L IGH
desired brightness level is reached. When the light is on, you may increase the
brightness level by pressing and holding the L L L L L IGH
level is reached, then release it.
AUTOMATIC DEMONSTRATION PROGRAM
Programmed into every Inteli-Touch Series fan is an Automatic
Demonstration Program. It can be used to fully demonstrate
and test the operation of the fan.
To enter the demonstration program:
1. Turn POWER off for at least three seconds. This will clear
the fan memory ready for programming.
2. Turn POWER on.
3. Immediately operate the buttons in the following sequence:
A multi-tone signal will verify the start of the test program
which proceeds as follows:
FAN + LIGHT + FAN + LIGHT + FAN
10
POWER
SPEED CONTROL
AN button until the desired speed is reached.
AN
AN
AN
REVERSING AIRFLOW
Note: A four-toned signal indicates the command was
accepted by the fan. A few seconds later the fan will
slow to a stop and then reverse direction.
LIGHT
IGH
IGHT T T T T button for less than
IGH
IGH
IGH
IGHT T T T T button is used. To maintain this
IGH
IGH
IGHT T T T T button until the
IGH
IGH
IGH
IGH
IGH
IGHT T T T T button until the desired
IGH
FAN CONTROL
ON - OFF
A momentary press
of the FAN button
TO CHANGE SPEED
Press and hold FAN
button longer than
one second
LIGHT CONTROL
ON - OFF
A momentary press of
the LIGHT button
TO CHANGE
BRIGHTNESS
Press and hold LIGHT
button longer than one
second
• Lights slowly increase to full intensity.
• Fan accelerates to speed three with audio tones.
• Light dims to half intensity.
• Fan accelerates to full speed with audio tones.
• Fan reverses at full speed with audio tones.
• Fan operates at full speed.
• Fan power is reversed with audio tones.
• Fan turns off with audio tones (blades coast for a short time).
• Lights turn off.
The complete cycle lasts slightly over one minute. It will continue
to repeat until the POWER is turned off for more than three
seconds, cancelling the program.
Advertisement
Table of Contents
