Casablanca Brescia Instructions Manual
  1. Manuals
  2. Brands
  3. Casablanca Manuals
  4. Fan
  5. Brescia
  6. Instructions manual

Casablanca Brescia Instructions Manual

Hide thumbs Also See for Brescia:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Owner's Manual, Owner's Manual & Installation Manual
®

InTRoDUCTIon

Preparation InSTRUCTIonS

fAn InSTAllATIon

ConTRol fEATURES:
INTELI•TOUCH OPERATION
3-SpEED opERATIon
Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product
and proper installation; therefore, before attempting to install and operate your Casablanca fan, read this
owner's manual completely and carefully. Retain this manual for future reference.
CAUTION:
To avoid possible electrical shock, make certain that electricity is turned off at the circuit breaker or fuse
box before attempting any installation procedure.
• CAUTION: RISK OF ELECTRICAL SHOCK! All wiring must be performed in accordance with national and local electrical codes. If you
are unfamiliar with the wiring codes, you should use a qualified electrician. To avoid overheating and possible damage to other equipment,
do not install control to a receptacle, fluorescent light fixture, motor operated appliance, or transformer-supplied appliance.
• This fan is designed to be installed on an existing electrical outlet box. The outlet box must be UL Listed for ceiling fan installations, if it is
not, a new box must be installed. Casablanca extension poles are available for sloped or high ceiling installations.
• This ceiling fan requires a grounded electrical supply of 120 VAC, 60 Hz and a minimum 15 amp circuit. The maximum current requirement
for the fan with light fixture is 3.8 amps. The fan uses about 1 amp or 100 watts. Maximum light current is 2.8 amps or 340 watts of lighting.
• Where wire nuts are employed, be sure all bare wires are within the connectors. When installing the canopy hatch, make sure all wires
are within the canopy and that no wires are being pinched.
• The blades in each pack are matched for equal weight
to assure smooth fan operation. If more than one fan
is being installed, be careful not to mix blades from
different cartons.
• Inspect the contents of your carton for possible ship-
ping or handling damage and report any such damage
directly to your authorized Casablanca dealer.
• It is always a good idea to have an assistant to help
with the installation.
• When cleaning, painting, or working near your fan,
be very careful of the fan and blades. Always turn the
power OFF to the ceiling fan before servicing it, work-
ing on it, or replacing light bulbs.
• Never insert anything into the path of the fan blades
while the fan is in operation.
Never install a fan over a pool or spa.
•
• Never operate a fan that has been damaged in any
way. Contact Casablanca Fan Company by calling toll
free 1-888-227-2178, or contact your local authorized
Casablanca dealer for assistance in obtaining service.

CONTENTS

3
READ AND SAVE THESE INSTRUCTIONS

SAFETY FIRST

InTRoDUCTIon

BEfoRE yoU START

For best performance and for your warranty to be valid,
use only genuine Casablanca blades, light fixtures, and accessories.
PN 9543Z
SAfE USE
fUSE BoX
(REmovE fUSE foR ThE
CIRCUIT yoU wIll BE
woRKIng on)
CIRCUIT BREAKER
(TRIp BREAKER foR ThE
CIRCUIT yoU wIll BE
woRKIng on)
HN0210
1
2
3
4
10
16
18
18"
70"
84"
1

Advertisement

Table of Contents
loading

Related Manuals for Casablanca Brescia

Summary of Contents for Casablanca Brescia

  • Page 1: Fan Installation

    Never install a fan over a pool or spa. • • Never operate a fan that has been damaged in any way. Contact Casablanca Fan Company by calling toll free 1-888-227-2178, or contact your local authorized Casablanca dealer for assistance in obtaining service.
  • Page 2 moUnTIng RECommEnDATIonS Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation, and fan size are all important factors to consider before installation. Location Ceiling fans have practical uses in almost every room in your home. We suggest you follow these mounting recommendations as you decide where to install your Casablanca fan.

  • Page 3: Important Safety Information

    ® rescia pREpARATIon InSTRUCTIonS Unpacking: Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them against the parts listed here. Before discarding packaging material, be certain that all parts have been removed. pERmA • loCK™ hARDwARE AllEn SET SCREw DownRoD & BAll ⁄ -20 x ⁄ ” ASSEmBly 1/8” (pRE-InSTAllED) AllEn wREnCh fAn pREpARATIon ImPOrTANT SAfETy INfOrmATION!
  • Page 4 CRoSSBAR moUnTIng BRACKET InSTAllATIon JoIST Note: After removing the old fixture, check the outlet box to insure that it is supported by a joist or beam across its upper surface. If not, a 2” x 4” stud must be installed. Step 1. Remove the knockout plug in the center of the outlet box or drill a ″ hole for the lag screw to pass through. Then drill a ″ guide hole into the joist or beam to a depth of 3″. Step 2. Route the outlet box wires through the keyhole slot of the crossbar mounting bracket as shown.
  • Page 5 ® rescia lAg SCREw InSTAllATIon Step 3. With the large washer attached, pass the lag screw through the center hole of the crosbar mounting bracket and screw into guide hole. Tighten until outlet box is firmly mounted to beam. This box must be firmly secured to the ceiling. We recommend that the ceiling fixture outlet box be of sufficient capacity enabling it to support the weight of fan and light fixture under any conditions.
  • Page 6 hAngIng ThE fAn Step 5. To hang the fan body in the canopy, hold the fan body firmly and insert the ball into the canopy opening. Check that no wires were pinched. Rotate the fan body until the slot in the ball fits into the pin opposite the canopy opening. BAll Fan Hanging Weight is 27 lbs SloT CANOPY ELECTRICAL CONNECTIONS Step 6a. Attach the fan wires to the ceiling fixture outlet box WIRE NUT W-85 CONNECTIONS wiring by twisting the bare ends of the wires together and then...
  • Page 7 ® rescia InSTAllIng ThE BlADE/BlADE holDER To fAn moToR pREpARATIon Step 10. To reach the blade holder mount- ing holes in the fan motor the dummy switch housing must be removed. Take out the two 5-32 X ” screws securing the dummy switch housing and remove. Set the two (2) screws aside for the moment, they will be used in Step 15 to install the switch housing after the blades are installed.
  • Page 8 REmovE ShIppIng BloCKS ShIppIng Step 12. On the flywheel remove the four BloCKS shipping blocks by unscrewing the screws. Discard the shipping blocks and shipping block screws. BlADE/BlADE holDER InSTAllATIon Step 13. Using the screws from the pack, attach each blade/blade holder assembly to the motor. Using the screwdriver, tighten securely by hand only.
  • Page 9 ® rescia SwITCh hoUSIng pREpARATIon Step 14. Locate the switch housing/cap as- sembly and remove the two 8-32 X ″ screws SwITCh hoUSIng holding the cap onto the switch housing. CAp SCREw Note: Save these two screws– ″ 8-32 X they will be used in Step 18! InSTAllIng ThE SwITCh hoUSIng ASSEmBly Step 15. Attach the two (2) 5-32 X ″ switch housing screws removed in Step 10 (on Page 7) to fan motor as shown, leaving ⁄...
  • Page 10 ® W-85 ContRol inStallation WALL CONTROL AND HARDWARE (not to scale) (4) Wire Cap Wall Plate W-85 Switch Bezels Switch Mounting Screws White Wall Almond Wall Wall Control (1) White Screws (2) (2) White Plate(1) Plate(1) (1) Almond (2) Almond WaRning! BEZEL To avoid possible electrical shock, make cer- tain that electricity is turned off at the circuit breaker or fuse box before attempting any in- stallation or repair procedure...
  • Page 11 ® W-85 Wall Control Bezel replacement: - ALMOND ContinUED BEZEL Step 19c. Reinstall the rubber key pad on to the four (4) locating pins located on the almond bezel as shown in Figure #3 and #4. RUBBER KEY Figure #3 RUBBER KEY Step 19d. To attach the bezel back on to the front of the switch you will need to align the four (4) tabs on the bezel with the front of the wall control and by gently pressing on both top and button of the bezel at the same time, snap the bezel back on to the front of the switch as shown in figure #5.
  • Page 12 ® inStalling thE W-85 Wall ContRol NOTE: W-85 Wall Control should only be installed on Casablanca's Inteli-Touch 3 fans with DOWNLIGHTS ONLY. ® The wall control installs in the same manner as an ordinary light switch, using an existing wall box and wiring. This controller is designed to signal the fan microcomputer as well as perform normal switching operations.
  • Page 13 ® DUAL W-85 INSTALLATION DiP SWitChES To control the fan and lights from two locations (a three-way circuit), use two W-85 wall controls as shown in the wiring diagram in Figure #5. Before installing the two switches into the wall, place both switches side by side, then locate the 4 dip switches on the side of the two switches. Then make sure that the dip switches are set to the same address on both switches as shown in Figure #4. When setting these dip switches you are setting the channel number that is required to control both your fan and lights from both sides of the room.
  • Page 14 ® OPERATION POWER button is normally left in the on position. Always turn the power off during cleaning or servicing the fan and during thunderstorms. It is also used to exit or enter ad- ditional programs. button must be left on to retain a previously set fan speed or light level. OPERATION SPEED CONTROL There are six individual speed settings for the fan;...
  • Page 15 ® CHANGING FREqUENCY SETTING NOTE: All fans leave the factory set to “1111” SWitChES You will only have to change the dip switch settings in the remote if you are using more than one fan in the same area and want to control them separately. Step 1. Turn power OFF at the circuit breaker or fuse box and at the toggle switch, for the fan you want to change.
  • Page 16 ® OPERATION SAFE-EXIT AND LIGHT -MINDER PROGRAM ® ® notE: Both Light-Minder and Safe-Exit programs will always run at the same time. The Safe-Exit Program gives you about thirty seconds of light when you turn the lights off, enabling you to exit your home before the lights go out. To enter the Safe-Exit Program: Safe-Exit 1) To operate the lights for Safe-Exit Program – Press the button off for at least five seconds. 2) Turn the Power on. Immediately press the buttons in the following sequence: . Immediately press the Button after an audio tone is heard from the fan controller.
  • Page 17 ® OPERATION FAN-MINDER PROGRAM ™ The Fan-Minder feature will add to your comfort when used in the bedroom. The program reduces the speed of the fan each two-hour interval to compensate for cooling night air. To enter the Fan-Minder Program: 1. Turn the OFF for at least 5 seconds. 2. Turn the 3. Immediately operate the buttons in the following sequence: 4. The fan will respond with three descending tones. A timer is now initiated and the fan will reduce one speed for each two-hour interval. The fan will not, however, descend below the second lowest speed. 5. You may increase the fan speed by pressing and holding the button until the desired speed is reached, then release it.
  • Page 18 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Note: Any changes or modifications to the transmitter or receiver not expressly approved by Casablanca Fan Company may void one’s authority to operate this remote control.
  • Page 19 3-Speed Pull-chain switches on the fan control the fan and lights. Using FAN & SPEED OPTIONAL LIGHT CONTROL the fan control pull-chain switch: Fan off at start. PULL CHAIN PULL CHAIN First pull: fan ON, low speed SWITCH SWITCH Second pull: medium speed Third pull: high speed Fourth pull: fan OFF Using the optional light pull-chain switch: Light off at start. First pull: light ON Second pull: light OFF Direction of blade rotation is controlled by the reverse slide switch REVERSE on the side of the switch housing. SWITCH No changes in household wiring are required. 3-SpEED opTIonAl lIghT fIXTURE InSTAllATIon NOTE: If a separate circuit is used to control the lights from a wall SWITCH...
  • Page 20 3-Speed opTIonAl 3-SpEED w-41 wAll ConTRol • The W-41 allows the choice of four (4) different speed settings. • No light fixture is used. • Set the FAN pull chain switch to the HIGH speed setting. • No changes in household or fan wiring are required. • The fan may be turned ON and OFF by the W-41 wall control. CaUtion! Failure to set the pull-chain speed to high can result in faulty operation of the fan and damage to the W-41 wall control.
  • Page 21 ® rescia TROUbLESHOOTING TIPS Please refer to this troubleshooting guide before requesting service or contacting your dealer for assistance. PRObLEM POSSIbLE REMEDIES Fan will not start • Check the main circuit fuses, circuit breakers, and wall switch position. Check all wire connections. Make sure the power is turned off during this inspection. •...
  • Page 22 CARE RECOMMENDATIONS Fan Finishes • For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the finish. • A vacuum cleaner brush nozzle can remove heavier dust. • Surface smudges or an accumulation of dirt and dust can be removed easily using a mild detergent and slightly dampened soft cloth. An antistatic agent may be used, but never use abrasive cleaning agents as these will damage the finish. Blades • Wood-finish blades should be cleaned with a furniture polishing cloth. Occasionally, a light coat of furniture polish may be applied for added protection and beauty. • For painted and high-gloss blades, surface smudges or an accumulation of dirt and dust can be removed easily using a mild detergent and slightly dampened soft cloth. An antistatic agent may be used, but never use abrasive cleaning agents as these will damage the finish.
  • Page 23 ® rescia PRODUCT SPECIFICATIONS Model Name: Brescia ® Motor: XLP 2000® Model Number: 95xxD/Z Blade Span: 44” & 52" Blade Iron Pitch: 15° Dimensions: A = 11.3" No. of Blades: B = 12.6" Technology: 3-Speed 3" Inteli•Touch 3 W-85 D = 14" E = 5.6"...

Table of Contents