Oneida Air Systems Dust Deputy Deluxe Owner & User Manual
Hide thumbs
Also See for Dust Deputy Deluxe:
- Owner's manual (4 pages) ,
- Manual (24 pages) ,
- Manual (32 pages)
Related Manuals for Oneida Air Systems Dust Deputy Deluxe
Summary of Contents for Oneida Air Systems Dust Deputy Deluxe
- Page 1 Dust Deputy Deluxe # AXD000004A U.S. Pat. 6833016 RE40048 7282074 Appearance may vary slightly Rev: 01/09/2020 Doc. # ZBM000036DELA...
-
Page 2: System Start-Up Information
8. Can be used for collecting non-flammable liquids. 9. Dispose of waste in a FIRE SAFE AREA. SOME DUSTS ARE HIGHLY FLAMMABLE OR Ÿ EXPLOSIVE. LEARN/ KNOW WHAT YOU ARE DEALING WITH. FOLLOW ALL LOCAL, STATE, FEDERAL & NFPA CODES AND GUIDELINES. Oneida Air Systems... - Page 3 System Dimensions Nominal dimensions shown. Dimensions subject to slight variations in manufacturing. 6-3/4" 171 mm 8" Tapered Inlet 203 mm and Outlet 2" O.D. 1-7/8" I.D. 2.5" 51 mm O.D. 64 mm 48 mm I.D. 28.75" 730 mm 25 -1/8" 638 mm 13-1/4"...
- Page 4 AXD200036 2" x 36" Hose AXD600103A 2" Elbow ACB320000 Clamp Band AFO990225 O Ring Please unpack the parts carefully and confirm you have received each item listed here. *Hardware is stored in between the two Buckets (F). Oneida Air Systems...
- Page 5 System Contents (Continued) oneida-air.com...
- Page 6 Lid (E) against Gasket and align all the holes. Secure Cyclone, Gasket and Lid together using six Bolts (C1), six Washers (C2), and six Whiz-Lock Nuts (C3) as shown in [FIG. 1]. Note: Tighten hardware evenly to eliminate air leaks. DO NOT OVERTIGHTEN! FIG. 1 Oneida Air Systems...
- Page 7 Assembly Instructions (Continued) Snap Cyclone (A) and Lid (E) assembly onto one of the Buckets (F) and ensure it's fully seated.[FIG. 2]. FIG. 2 oneida-air.com...
- Page 8 1" from the outside edge. Using a 5/16" drill bit, drill into the Bucket at all four marked locations. Note: The fourth hole is to relieve vacuum pressure inside the side-car Bucket. Safety Instructions WARNING! Blank Oneida Air Systems Logo FIG. 4 Oneida Air Systems...
- Page 9 Assembly Instructions (Continued) Install the Caster Hardware Pack (H) to the Bucket (F). Install Wheels (H3) at three of the previously drilled hole locations using two Washers (H2), and one Nylock Nut (H1)[FIG. 5]. Note: To make sure the safety instructions are not covered up when attaching to your wet/dry vacuum, DO NOT install a caster into the hole on the “Blank”...
- Page 10 Carefully drill two 1/4" holes at all marked locations [FIG 7]. Note: If you decide to detach the Bucket from your wet/dry vacuum; seal the holes with a bolt, washer, nut and silicone. FIG. 7 Oneida Air Systems...
- Page 11 Assembly Instructions (Continued) Fasten your Bucket (F), Foam Spacer Block (G) and your wet/dry vacuum with two Carriage Bolts (C5), four Fender Washers (C4) and two Whiz-Lock Nuts (C3) as shown in [FIG. 8]. FIG. 8 oneida-air.com...
- Page 12 Assembly Instructions (Continued) Insert the previously assembled Dust Deputy into the side car Bucket (F) [FIG. 9]. FIG. 9 Oneida Air Systems...
- Page 13 Assembly Instructions (Continued) Attach one Elbow (J) to the top outlet of the Cyclone (A) and affix Hose (I) to the tapered end of the Elbow. Attach the other open end of Hose to the second Elbow and attach to the inlet of your wet/dry vacuum. Connect the Cyclone's inlet (sideways facing port) to your dust producing tool with your vacuum's hose or ductwork [FIG.
- Page 14 Alternate Sidecar Ideas You are only limited by your imagination. Below are Ÿ some alternate sidecar setups that customers have created. Oneida Air Systems...
- Page 15 Adding Cyclones to Improve Performance Attach in Series To Tools Increases particle efficiency and helps in very fine dust situations. Top View Attach in Parallel To Tools Same particle efficiency but increases the CFM. Top View 200 CFM 100 CFM 100 CFM Multiple Vacuums More CFM/airflow to larger...
- Page 16 Install the Metal Tape (D) to the Cyclone (A) so that the inlet, outlet, and flange are attached by a continuous, conductive path. The tape should wrap 1/4" around the edge of each opening [FIG 11]. FIG. 11 Oneida Air Systems...
- Page 17 Optional Grounding Instructions (Continued) For added grounding, attach a self-supplied wire with a ring terminal on one end and a washer tied to the other end when installing one of the bolts in step 1 on page 6. The wire must be long enough for the washer to lie on the floor [FIG 12].
-
Page 18: Troubleshooting
2. Use a hose clamp. 3. Wrap the inlet and outlet of the Dust Deputy with a layer of electrical tape to increase the friction fit. 4. Secure hose with a sheet metal screw. Oneida Air Systems... - Page 19 Troubleshooting Air Leaks Even a small leak can significantly affect the overall Ÿ separation performance of the cyclone [FIG. 13]. If you can't audibly pinpoint where the leak might be coming from, one of the simplest ways to check for air leaks is with a smoke test.
- Page 20 The hardware is stored between the two buckets included in the kit. What do I need to hook up my Dust Deputy to my vacuum? Our Dust Deputy Deluxe Kit is ready to go right out of the box for most wet-dry vacuums. However, not all wet-dry vacuums are identical and may need an adapter to attach.
- Page 21 What is the minimum air watts needed for the Dust Deputy? Rather than worrying about what specs your vacuum needs (e.g. air watts, cfm, static lift, etc.), we at Oneida Air Systems have a much simpler approach - simply match the size of your vacuum's inlet to the size of the Dust Deputy cyclone's ports.
- Page 22 Please contact our customer service department for assistance at 1-866-387-8822 or support@oneida-air.com Is the Dust Deputy food-grade safe? No, the raw material is rated food-grade safe, but the additional anti-static material and the factory it's manufactured in are not rated food safe. Oneida Air Systems...
- Page 23 50 CFM to ensure optimum dust separation performance. The elbows that come with the Dust Deputy Deluxe Kit measure out to an ID of 2.25" and an OD. If your wet-dry vacuum hose or inlet is a different size you will need an adapter as noted in the FAQ "What do I need to hook up my Dust Deputy to my vacuum?".
- Page 24 2.5" Vacuum Hose Coupler #AXD225225 • Used for connecting separate lengths of 2.5" vacuum hose. • Slips over 2.25" O.D. hose cuffs and features a inner beaded section to complete the friction fitting. Oneida Air Systems...
- Page 25 Accessories (Continued) 2.5" Turnkey Hose Clamp #ACB360000 • Secures hose fitting in place to eliminate disconnects when pulling or flexing the hose. • Fits hoses and port sizes from 2" to 2-1/2" in diameter. 2.5" to 2" Vacuum Hose Screw-Cuff #VSHCEE001 • For connecting 2.5"...
- Page 26 1.5" x 6.5' Dust Extraction Hose Whip #AHE000001 • This highly flexible vacuum hose fits onto the dust collection ports of common portable power tools. Includes 2.5" rotating swivel cuff. Oneida Air Systems...
- Page 27 LID MOUNTING TEMPLATE Dust Deputy Template FOR STANDARD 14" TALL DUST DEPUTY CYCLONES Use this template if you want to reinforce your lid. 1:1 SCALE. DO NOT ALTER DOCUMENT SIZE WHEN PRINTING oneida-air.com...
- Page 28 LID MOUNTING TEMPLATE Mirrored Dust Deputy Template FOR STANDARD 14" TALL DUST DEPUTY CYCLONES Use this template if you want to reinforce your lid. 1:1 SCALE. DO NOT ALTER DOCUMENT SIZE WHEN PRINTING Oneida Air Systems...
- Page 29 Foam Block Template Cut out this template and use it to position where the block will be located on your shop vacuum. You can reposition the bolt holes if need be according to your vacuum’s structure. oneida-air.com...
- Page 30 Mirrored Foam Block Template Cut out this template and use it to position where the block will be located on your shop vacuum. You can reposition the bolt holes if need be according to your vacuum’s structure. Oneida Air Systems...
-
Page 31: Warranty Information
Limited Warranty – Activate online at oneida-air.com/warranty Oneida Air Systems®, Inc. (OAS) warrants the Dust Deputy for a period of 1 year, to the original purchaser from the date of purchase, unless otherwise specified. Items not manufactured by Oneida Air Systems are limited to their own manufacturer’s warranties. All electrical items such as magnetic starters, remotes, sensors, pumps, bin sensors, bag grippers, etc. - Page 32 Regardless of where you purchased your Oneida Air Systems' product, if you have any questions or issues with missing / damaged parts, please call Oneida Air Systems first to let us help resolve your problem. We fully stand behind the quality of our products and place the utmost value on the satisfaction of our customers.