"Fast Heat Up" Function; Demo Mode; Error Code; Beep" Mode - John Lewis JLBIOS602 Instruction Manual

"Fast Heat Up" function

"Fast Heat Up" function
"Fast Heat Up" function "Fast Heat Up" function "Fast Heat Up" function
After a cooking function has been selected and the temperature has
been adjusted, the cavity will gradually heat up until the selected
temperature is reached. This will take from 10 to 15 minutes, depending
on selected function and temperature.
If it is necessary to reach the required temperature in a shorter time,
the "Fast Heat Up" Function can be used.
1) Switch the oven on by pressing button
2) Set the required cooking function and temperature as explained in
the previous pages.
3) Set the temperature by pressing button " " or " ". The
temperature will appear on the display.
4) Press button Fast heat up . The temperature display will show
"FHU" (Fig. 18).
5) press button Oven function and the symbol "° ° ° ° ° " will flash for
approximately 10 seconds. Now it is possible to select the required
temperature by pressing button " " or " ".
4) When the required temperature is reached, an acoustic alarm will
sound for a short time, and the temperature display will revert to
the set temperature.
This function can be used with any cooking function or temperature.

Demo mode

Demo mode Demo mode
Demo mode Demo mode
This mode is intended to be used in the shops to demonstrate the
oven functionality without any power consumption except the oven
lamp ,the display and the oven fan.
This function can only be switched on when the appliance is connected
to the electrical supply for the first time. If there is a power failure,
when the power supply is restored again, the Demo mode can only be
switched on if in the display 12:00
1) Press button Time functions for approximately 2 seconds. An
acoustic alarm will sound for a short time.
2) Press buttons Time functions and
acoustic alarm will be heard and the indication12:00 will appear in
the display (Fig. 19).
When the oven is switched on, the symbol
This means that the Demo mode is activated. All oven functions can be
selected.The oven is not really working as the heating elements do
not switch on.
Switch off the oven and follow the above described Switch off the oven and follow the above described Switch off the oven and follow the above described
Switch off the oven and follow the above described Switch off the oven and follow the above described
procedure to disable the demo mode. procedure to disable the demo mode. procedure to disable the demo mode.
procedure to disable the demo mode. procedure to disable the demo mode.
The Demo function remains saved in the programme in
the event of a power failure.
Er Er Er Er Err r r r r or code or code or code
or code or code
The electronic programmer does a continuous diagnostic check of the
system. If some parameters are not correct, the control unit will stop
the activated functions and it will show on the display the correspond-
ing error code.
For further details, refer to chapter "Something not working"
on page 24.

"Beep" Mode

"Beep" Mode "Beep" Mode "Beep" Mode "Beep" Mode
You can choose to make the Electronic Control beep each time
that a control is touched.
To enable this function, the oven must be off.
1) Press buttons Oven functions and
about 3 seconds. The Electronic Control beeps once (Fig. 20).
To disable the "Beep" Function: To disable the "Beep" Function: To disable the "Beep" Function: To disable the "Beep" Function: To disable the "Beep" Function:
1) If the oven is on, press button
2) Press buttons Oven functions and " " at the same time for
about 3 seconds. The Electronic Control beeps once.
14
.
12:00 12:00
12:00 and the symbol 12:00 are flashing.
" "
at the sametime. A short
appears in the display.
" "
at the same time for
to switch it off.
Fig. 18 Fig. 18
Fig. 18 Fig. 18 Fig. 18
Fig. 19 Fig. 19
Fig. 19 Fig. 19 Fig. 19
Fig. 20 Fig. 20
Fig. 20 Fig. 20 Fig. 20