Bosch UPH-2D Series Instruction Manual
  1. Manuals
  2. Brands
  3. Bosch Manuals
  4. Security Camera
  5. UPH-2D Series
  6. Instruction manual
Bosch UPH-2D Series Instruction Manual

Bosch UPH-2D Series Instruction Manual

High speed pan/tilt system
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
High Speed Pan/Tilt System
UPH-2D, UPH-3D, UPH-Z Series
en
Instruction Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the UPH-2D Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Bosch UPH-2D Series

Summary of Contents for Bosch UPH-2D Series

  • Page 1 High Speed Pan/Tilt System UPH-2D, UPH-3D, UPH-Z Series Instruction Manual...

  • Page 3: Table Of Contents

    Switching On and Off Configuring the Device On-screen Display (OSD) Using the Joystick Moving Around the Menus 10.1 Keyboard Commands List 10.2 Changing the Settings 10.3 Changing the Numeric Fields Bosch Security Systems Instruction Manual F01U.073.990 | Version 1.0 | 2007.07...
  • Page 4 Speed Menu 11.3.2 Limits 11.3.3 Preset/Patrol/Autopan 11.3.4 Wiper-Washer 11.3.5 Alarms 11.4 Camera Parameters 11.4.1 UPH-2D and UPH-3D Series (Dinion Cameras) 11.4.2 UPH-Z Series (camera module) 11.5 Creating a New Dynamic Mask 11.6 Load Default Configuration 11.7 Setup Info Menu Maintenance 12.1 Cleaning 12.2...

  • Page 5: Safety

    10. Replacement parts - Be sure the service technician uses replacement parts specified by the manufacturer, or that have the same characteristics as the original parts. Unauthorized substitutions may cause fire, electrical shock, or other hazards. Bosch Security Systems Instruction Manual F01U.073.990 | Version 1.0 | 2007.07...

  • Page 6: Safety Precautions

    13. Attachments, changes or modifications - Only use attachments/accessories specified by the manufacturer. Any change or modification of the equipment, not expressly approved by Bosch, could void the warrantee or, in the case of an authorization agreement, authority to operate the equipment.

  • Page 7: Important Notices

    Permanently connected equipment - Incorporate a readily accessible disconnect device in the building installation wiring. Video loss - Video loss is inherent to digital video recording; therefore, Bosch Security Systems cannot be held liable for any damage that results from missing video information. To...
  • Page 8 | Safety High Speed Pan/Tilt System redundant recording systems, and a procedure to back up all analog and digital information. Copyright This user guide is the intellectual property of Bosch Security Systems and is protected by copyright. All rights reserved. Trademarks All hardware and software product names used in this document are likely to be registered trademarks and must be treated accordingly.

  • Page 9: Unpacking

    Verify that all the parts listed in Section 2.1 Parts List are included. If any items are missing, notify your Bosch Security Systems Sales or Customer Service Representative. The original packing carton is the safest container in which to transport the unit and must be used if returning the unit for service.

  • Page 10: Safety Rules

    Description The Bosch High-Speed Positioning System is a complete, high-performance, high quality solu- tion that can pan 360 degrees continuously at speeds of up to 100 degrees per second. An extensive range of options lets you tailor the system to your specific requirements. For exam-...

  • Page 11: Installing The High Speed Pan/Tilt

    The cables should not be accessible by unauthorized personnel; cables should be secured to fixed locations at appropriate intervals to bare the weight of the cables, e.g. cables running inside a tall camera pole. Bosch Security Systems Instruction Manual F01U.073.990 | Version 1.0 | 2007.07...
  • Page 12 5 Nm; use a calibrated torque wrench to ensure closure. Position the base on the optional wall or pole mount, guiding the cables so that they are positioned inside the wall or pole mount (see Figure 4.3). F01U.073.990 | Version 1.0 | 2007.07 Instruction Manual Bosch Security Systems...
  • Page 13 10 mm or more to prevent the stretch dis- connecting. 10. Cover the cable with a plastic tube and fix it with the tie thread. Bosch Security Systems Instruction Manual F01U.073.990 | Version 1.0 | 2007.07...

  • Page 14: Wiring The Video Cable

    Use a small screwdriver to press down on the VIDEO push latch (see Figure 4.6) and attach the center conductor to the VIDEO terminal. Fig. 4.6 Wiring the Terminal Note: The above terminals support AWG 20 (0.5 mm ) to AWG 28 (0.08 mm F01U.073.990 | Version 1.0 | 2007.07 Instruction Manual Bosch Security Systems...

  • Page 15: Connecting The Power Supply

    24 VAC Terminal Connection Per local Installer Neutral Per local Installer Live/Active Green/Yellow Earth Wire Color 230 VAC Terminal Connection Blue Neutral Brown Live/Active Green/Yellow Earth Table 4.2 Terminal Connections Bosch Security Systems Instruction Manual F01U.073.990 | Version 1.0 | 2007.07...

  • Page 16: Wiring Biphase

    To wire for Biphase, connect the C+ terminal wire to the B+ terminal and the C- terminal wire to the B- terminal respectively. RS-232 RS-232 is used for firmware upgrades only (see Figure 4.8). Fig. 4.8 RS-232 Location F01U.073.990 | Version 1.0 | 2007.07 Instruction Manual Bosch Security Systems...

  • Page 17: Connecting The Washer Pump (Optional)

    (see Figure 5.1). Fig. 5.1 Installing the Washer Cables Reference # Description Base Cable Glands Washer Pipe Support Gasket Screw Seals Bracket or Pole Support Washers Screws Bosch Security Systems Instruction Manual F01U.073.990 | Version 1.0 | 2007.07...
  • Page 18 Lock the coupling using the supplied hoseclip and connect the delivery hose. 10. Calibrate the jet (see Figure 5.3) by directing the nozzle towards the glass of the housing. F01U.073.990 | Version 1.0 | 2007.07 Instruction Manual Bosch Security Systems...
  • Page 19 Connecting the Washer Pump (optional) | en Fig. 5.3 Calibrating the Nozzle The diagram below refers to the 19-pin connector on the base board of the pan/tilt. Fig. 5.4 Connecting the Washer Pump Bosch Security Systems Instruction Manual F01U.073.990 | Version 1.0 | 2007.07...
  • Page 20 F1-F2 wiper option). Note: Only required for UPH-Z Series; not required for UPH-2D or UPH-3D Series. Fig. 5.5 Connecting the Washer System with Level Sensor Capabilities NOTICE! The HAC-WAS05-10 washer system does not have a level sensor. Therefore, it is not necessary to connect the alarm input.

  • Page 21: Connecting The Peripherals

    Alarm in, voltage-controlled (10-35 VDC), and A4 referred to common COM B+ and B- Biphase communication lines CAUTION! The system is TNV-1 type, do not connect to SELV circuits. Bosch Security Systems Instruction Manual F01U.073.990 | Version 1.0 | 2007.07...

  • Page 22: Attaching The Top Unit

    Place the unit on the base. Align the tabs on the sides (see Figure 6.2) and verify that the parts are positioned correctly. Be careful not to pinch any of the wires. F01U.073.990 | Version 1.0 | 2007.07 Instruction Manual Bosch Security Systems...
  • Page 23 Push down to snap into place. Attach the top unit to the base using the supplied attachment screws and corresponding seals (see Figure 6.3). Tighten the base with a 4 mm Allen wrench. Bosch Security Systems Instruction Manual F01U.073.990 | Version 1.0 | 2007.07...
  • Page 24 Fig. 6.3 Attaching the Top Unit Reference # Description Configuration Window Base Screw Screw Seal Gasket CAUTION! Medium Risk: Place safety label near unit that warns of moving parts. Fig. 6.4 Safety Label F01U.073.990 | Version 1.0 | 2007.07 Instruction Manual Bosch Security Systems...

  • Page 25: Configuring The Device

    PROGRAM. ON and PROGRAM. OFF. During normal use, make sure the rocker for DIP switch No. 1 is OFF (PROGRAM. OFF). DIP-SWITCH 1 (for updating the firmware) Program ON Program OFF Table 7.1 Updating the Firmware Bosch Security Systems Instruction Manual F01U.073.990 | Version 1.0 | 2007.07...

  • Page 26: Protocol Switches

    Bilinx and Biphase Switches: Dip-switch 1 is used to enable the line termination of Biphase serial line. Dip-switch 2 is used to select the video format (ON = PAL, OFF = NTSC). F01U.073.990 | Version 1.0 | 2007.07 Instruction Manual Bosch Security Systems...

  • Page 27: Address Combinations

    High Speed Pan/Tilt System Configuring the Device | en 7.3.1 Address Combinations Fig. 7.2 Address table Bosch Security Systems Instruction Manual F01U.073.990 | Version 1.0 | 2007.07...

  • Page 28: Connections

    The camera menu setup of UPH-Z Series is done via the OSD, i.e.: AUX ON - 200 - Enter. The camera menu setup of UPH-2D and UPH-3D Series is done via two different AUX commands, i.e.: AUX ON - 46 - Enter (Dinion...
  • Page 29 - or- RS-485 RS485 Divar Divar Bilinx/Video Video UPH Series: unitized pan/tilt head Intuikeyboard RS485 BOSCH BOSCH Prod Prod Shot Allegiant + LTC 8016 Shot Divar - Bilinx RS-485 Bilinx/Video Bosch Security Systems Instruction Manual F01U.073.990 | Version 1.0 | 2007.07...
  • Page 30 DiBos 8 Video UPH Series: unitized pan/tilt head Video DiBos 8 LTC 8786 RS-232 Biphase Vidos, IE, DiBos 8, Bosch VMS or equivalent RS485-2 VIPX1 Ethernet Ethernet Video Fig. 7.3 Connection Diagrams F01U.073.990 | Version 1.0 | 2007.07 Instruction Manual...

  • Page 31: Switching On And Off

    Make sure the power source and connecting cables are suitable for the power consumption of the system. CAUTION! Do not stay in the vicinity of the device when it is powered. There is a risk of crushing. Bosch Security Systems Instruction Manual F01U.073.990 | Version 1.0 | 2007.07...

  • Page 32: On-Screen Display (Osd)

    During normal UPH operation, it is possible to activate the on-screen menu in order to set the advanced functions using the corresponding key/s. When using a Bosch keyboard, control the OSD with the Iris and Focus buttons. For dynamic masking, the SET - 1 - Enter and SET - 2 - Enter keys are used.

  • Page 33: Keyboard Commands List

    Recalibrate presets: AUX ON - 204 - Enter Autopan (requires left and right limits to be set in OSD) Autopan start: AUX ON - 1 - Enter Autopan stop: AUX OFF - 1 - Enter Bosch Security Systems Instruction Manual F01U.073.990 | Version 1.0 | 2007.07...

  • Page 34: Changing The Settings

    After identifying the desired selection, press the confirmation (Focus) button; the param- eter stops flashing. Note: For UPH-2D and UPH-3D Series (Dinion ) models, use up and down to scroll through the menus, Focus to enter a submenu, and left and right to change values.

  • Page 35: Language Menu

    3 - PRESET POSITION 4 - TILT LIMIT TITLE 5 - VIDEO SIGNAL 6 - INTERLACED VIDEO 7 - AREA PARAMETERS 8 - DISPLAY PARAMETERS Fig. 11.3 Display Setup Menu Bosch Security Systems Instruction Manual F01U.073.990 | Version 1.0 | 2007.07...
  • Page 36 Once it has finished the process and corrected for the effect of any environmental factors, the user regains full control. F01U.073.990 | Version 1.0 | 2007.07 Instruction Manual Bosch Security Systems...

  • Page 37: Area Parameters Menu

    For example, if this value is set to OFFSET PAN +0.00 +45.0 ° then all references will be shifted in +180.00 PAN by +45 ° with respect to the system’s physical reference. Bosch Security Systems Instruction Manual F01U.073.990 | Version 1.0 | 2007.07...

  • Page 38: Changing The Edit Text Menu

    To skip a space while in edit mode, press the Iris button, then move the joystick to the right past the number spaces you would like to skip. Press the Focus button to resume adding values. F01U.073.990 | Version 1.0 | 2007.07 Instruction Manual Bosch Security Systems...

  • Page 39: Display Parameters

    These set the position of reference to the titler so that the text Delta can be centralized. Address Number If enabled, the address number of the unit is shown at the top left of the screen during normal operation. Bosch Security Systems Instruction Manual F01U.073.990 | Version 1.0 | 2007.07...

  • Page 40: Motion Parameters Menu

    4 - SPEED 4... 10.0 gr./s 5 - SPEED 5... 20.0 gr./s 6 - SPEED 6... 30.0 gr./s 7 - SPEED 7... 40.0 gr./s DEFAULT Fig. 11.9 Speed Menu F01U.073.990 | Version 1.0 | 2007.07 Instruction Manual Bosch Security Systems...
  • Page 41 This is useful when the zoom is in telephoto (i.e. zoomed in); it slows down the pan and tilt speeds so that very fine adjustments can be made to follow moving subjects. Bosch Security Systems Instruction Manual F01U.073.990 | Version 1.0 | 2007.07...

  • Page 42: Limits

    RAMP TYPE Changes start and stop times for 000 - 012 the UPH. The higher the number, the greater the acceleration/decel- eration during starting/stopping. F01U.073.990 | Version 1.0 | 2007.07 Instruction Manual Bosch Security Systems...

  • Page 43: Preset/Patrol/Autopan

    The camera pans continuously between right and left limit set- tings. MOTIONS RECALL Allows definition of action after an interval of inactivity (it can recall a patrol, autopan, home position, etc). Bosch Security Systems Instruction Manual F01U.073.990 | Version 1.0 | 2007.07...
  • Page 44 DWELL Dwell time during patrol and auto- 00001 00000 - pan movements. 01000 sec. TXT: PRESET NR. 1 Message displayed when the pre- set position is reached. F01U.073.990 | Version 1.0 | 2007.07 Instruction Manual Bosch Security Systems...
  • Page 45 00001 - 01000 position. FORCE PRST DW.TIME Forces the default dwell time value YES, NO for all presets. FORCE PRST SPEED Forces the default speed value for YES, NO all presets. Bosch Security Systems Instruction Manual F01U.073.990 | Version 1.0 | 2007.07...
  • Page 46 REACHED SPEED Speed for reaching the home posi- 20.0 .1 - 100.0 tion when it is loaded. Note: Increase the reached speed from the default value to reach presets faster. F01U.073.990 | Version 1.0 | 2007.07 Instruction Manual Bosch Security Systems...
  • Page 47 RANDOM Enables execution of the Patrol YES, NO function by passing through the defined positions in a random manner. The random sequence is continually recalculated. Bosch Security Systems Instruction Manual F01U.073.990 | Version 1.0 | 2007.07...
  • Page 48 Enables the type of movement to HOME HOME, be loaded. AUTOPAN, PATROL DWELL BEFORE ACT. Interval that the joystick is inactive 00050 00005 - before the movement setting is 01000 sec. loaded. F01U.073.990 | Version 1.0 | 2007.07 Instruction Manual Bosch Security Systems...

  • Page 49: Wiper-Washer

    The amount of time that the wiper 00005 00001 - wipes. 00050 DELAY WIPER OFF The amount of time that the wiper 00002 00001 - wipes without water. 00050 Bosch Security Systems Instruction Manual F01U.073.990 | Version 1.0 | 2007.07...

  • Page 50: Alarms

    There are some differences between the UPH-Z Series, and the UPH-2D and UPH-3D Series. Figure 11.4.1 refers to the camera parameters of the UPH-2D and UPH-3D Series, i.e. units cameras and motorized zoom lenses. Figure 11.4.2 refers to the camera module with Dinion parameters of the UPH-Z Series.

  • Page 51: Uph-2D And Uph-3D Series (Dinion Xf Cameras)

    High Speed Pan/Tilt System Configuring the System | en 11.4.1 UPH-2D and UPH-3D Series (Dinion Cameras) MODULE PARAMETERS MODULE PARAMETER 1 - ENABLED ZOOM : 1 - ZOOM/FOCUS/IRIS 2 - WINDOW ZOOM 2 - AREAS MASKING 3 - ENABLED FOCUS :...

  • Page 52: Uph-Z Series (Camera Module)

    Description Default Options MANUAL SPEED The speed can take values 000 - 007 between 0 (minimum speed) and 7, maximum speed. OPTICAL AND DIGIT Enables digital zoom. YES, NO F01U.073.990 | Version 1.0 | 2007.07 Instruction Manual Bosch Security Systems...
  • Page 53 AUTOMATIC MODE: the exposure normally stays in automatic mode. Moreover, the user can override the exposure manually via Iris. FOCUS MIN LIMIT Set the minimum object distance 016 - 192 for focus (cm). Bosch Security Systems Instruction Manual F01U.073.990 | Version 1.0 | 2007.07...
  • Page 54 The UPH automatically holds the position and the size of the masking, according to the area displayed. F01U.073.990 | Version 1.0 | 2007.07 Instruction Manual Bosch Security Systems...
  • Page 55 Enables the position where the mask was defined. CHANGING COLOUR Enables the color of the mask YELLOW VARIOUS being modified. MASK COLOR Enables the color of the mask. BLUE VARIOUS Bosch Security Systems Instruction Manual F01U.073.990 | Version 1.0 | 2007.07...

  • Page 56: Creating A New Dynamic Mask

    Note: The tilt angle at which you can set the mask is between -40 to +70 degrees. It is recom- mended that you set the mask size to larger than the object size (height and width) - this is to ensure masking even during pan, tilt and zoom. F01U.073.990 | Version 1.0 | 2007.07 Instruction Manual Bosch Security Systems...
  • Page 57 IMAGE STABILIZATION Turn on this feature when the YES, NO image is affected by vibration that causes the picture to move. Bosch Security Systems Instruction Manual F01U.073.990 | Version 1.0 | 2007.07...

  • Page 58: Load Default Configuration

    The Setup Info menu is used to check the device configuration and the software versions of the UPH boards. SETUP INFO MENU NET board MPP board: ver. BOSCH 1.7 ver. BOSCH 1.7 Apr. 27 2007 Apr. 27 2007 HD r.2 HD r.2...

  • Page 59: Maintenance

    T 4A L 250 V T 6.3A H 250 V 230 VAC 50/60 Hz T 4A L 250 V T 2A H 250 V Table 12.1 Fuse Values for Replacement Bosch Security Systems Instruction Manual F01U.073.990 | Version 1.0 | 2007.07...

  • Page 60: Troubleshooting

    Remove power to the unit, re-apply working improperly. power, and allow the device to go through its homing phase. NET board MPP board ver. Bosch 1.7 ver. Bosch 1.7 Apr 27 2007 Apr 27 2007 HD r.2 HD r.2 Protocol...

  • Page 61: Dimensions And Range Of Movement

    High Speed Pan/Tilt System Troubleshooting | en 13.1 Dimensions and Range of Movement 258 (10.16) 514 (20.24) Bosch Security Systems Instruction Manual F01U.073.990 | Version 1.0 | 2007.07...
  • Page 62 | Troubleshooting High Speed Pan/Tilt System 514 (20.24) (2.87) Fig. 13.1 Dimensions and Range of Movement F01U.073.990 | Version 1.0 | 2007.07 Instruction Manual Bosch Security Systems...

  • Page 63: Technical Specifications

    Vertical tilt speed Variable from 0.1 °/s to 40 °/s Operating temperature UPH-Z Series: -20 °C to +40 °C UPH-2D Series: -20 °C to +40 °C UHP-3D Series: -20 °C to +40 °C Power supply 230 VAC 50/60 Hz 24 VAC 50/60 Hz Current consumption 0.5 A (230 VAC)
  • Page 64 Bosch Security Systems Robert-Koch-Straße 100 D-85521 Ottobrunn Germany www.boschsecuritysystems.com © Bosch Security Systems, 2007...

This manual is also suitable for:

Uph-3d seriesUph-zUph-z series

Table of Contents