Operate the device only from the type of power source indicated on the label. – Unless qualified, do not attempt to service a damaged device yourself. Refer all servicing to qualified service personnel. Bosch Security Systems B.V. 2024-02 | V01 | DOC User manual...
Notice! Video loss is inherent to digital video recording; therefore, Bosch Security Systems cannot be held liable for any damage that results from missing video information.
Page 7
Bosch Security Systems Inc 130 Perinton Parkway 14450 Fairport, NY, USA For more information please contact the nearest Bosch Security Systems location or visit: www.boschsecurity.us Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Page 8
Security advisories, that is a list of identified vulnerabilities and proposed solutions: https://www.boschsecurity.com/xc/en/support/product-security/security- advisories.html Bosch assumes no liability whatsoever for any damage caused by operating its products with outdated software components. 2024-02 | V01 | DOC Bosch Security Systems B.V.
Page 9
Dispose such equipment according to local laws and regulations, to allow their reuse and/or recycling. This will help in conserving resources, and in protecting human health and the environment. Bosch Security Systems B.V. 2024-02 | V01 | DOC User manual...
If you cannot connect, the unit may have reached its maximum number of connections. Depending on the device and network configuration, each unit can have up to 50 web browser connections, or up to 100 connections via Bosch Video Client or BVMS. Password protection in camera The device is password-protected.
Page 11
Fill in the fields User name and Password. Click OK. If the password is correct, the desired page appears. Note: New releases of software may require you to set a new and stronger password. Bosch Security Systems B.V. 2024-02 | V01 | DOC User manual...
Click this icon to configure the device. Dashboard Click this icon to see detailed system information. Links Click this icon to navigate to the Bosch download store. Logout Click this icon to log out of the device. Click this icon to get context-sensitive help for the page you are browsing.
The Dashboard is only visible in the application bar if the Show 'Dashboard' option is enabled by a service-level user in the Configuration -> Web Interface -> Appearance page. Bosch Security Systems B.V. 2024-02 | V01 | DOC User manual...
If you hover over the right-hand icon, the network load is shown. This information can help with problem solving or when fine tuning the unit. For example: – if the storage activity is too high, change the recording profile, 2024-02 | V01 | DOC Bosch Security Systems B.V. User manual...
Expand the Connection group on the left side of the browser. To view a recording stream: – Click the Recording drop-down arrow to see the options. – Select one of the numbered recording streams. Bosch Security Systems B.V. 2024-02 | V01 | DOC User manual...
The Dashboard page shows information on 4 topics: – Device status – Recording status – Connection Status – Services You can also download a .JSON file with information about the device: 2024-02 | V01 | DOC Bosch Security Systems B.V. User manual...
Page 17
Operation via the browser | en At the bottom of the page, locate the Export button Click the Export button Select a location in your hard drive to store the file Bosch Security Systems B.V. 2024-02 | V01 | DOC User manual...
Certificate. A check mark in this check box indicates that at least one certificate is loaded onto the device. The Trusted certificate is a root certificate for Bosch Security Systems that proves that the device meets the following criteria: –...
Configuration | en – It has not been tampered with. The Trusted certificate is issued by Escrypt. Escrypt is a Bosch company and Certificate Authority (CA). – Active Directory server (AD FS). A check mark in this check box indicates that the device uses an active directory server.
The default language is English. After setting the new language, the page refreshes automatically. The GUI now displays field names and options, as well as OSD messages, in the selected language. 2024-02 | V01 | DOC Bosch Security Systems B.V. User manual...
Page 21
You can specify the interval at which the individual images should be generated for the M- JPEG image on the Live page. Enter a time interval (in milliseconds). The default is 0. Bosch Security Systems B.V. 2024-02 | V01 | DOC User manual...
Four separate accounts can be defined for posting and recording export. Type Select the account type. Account name Enter an account name to be shown as the target name. IP address Enter the IP address for an FTP server. 2024-02 | V01 | DOC Bosch Security Systems B.V. User manual...
To transfer the IP address of the device, click the Register button. Status The status of the DynDNS function is displayed here for information purposes; these settings cannot be changed. Click Set to apply the changes. Camera 5.4.1 Installer Menu Bosch Security Systems B.V. 2024-02 | V01 | DOC User manual...
Page 24
The Focus indicator shows a value related to the focus quality of the image. The higher the value, the more in focus the image will be. – Lens – Indicates the lens type in use. 2024-02 | V01 | DOC Bosch Security Systems B.V. User manual...
Select the background color for the alarm message to be displayed in. If you have enabled the Transparent background option, the background color is not displayed in the OSD. Bosch Security Systems B.V. 2024-02 | V01 | DOC User manual...
Page 26
– Text color Select the color for the alarm message to be displayed in. – Background color Select the background color for the alarm message to be displayed in. 2024-02 | V01 | DOC Bosch Security Systems B.V. User manual...
The mounting position describes the perspective information that is also often called calibration. In general, the mounting position is determined by the parameters of the camera such as height, roll angle, tilt angle, and focal length. Bosch Security Systems B.V. 2024-02 | V01 | DOC User manual...
Page 28
Alternatively, the user can still resort to the Sketch-based calibration to manually input the calibration values. 2024-02 | V01 | DOC Bosch Security Systems B.V. User manual...
Page 29
The Coordinate system feature describes the position of the camera in a local Cartesian or the global WGS 84 coordinate system. The camera and the objects tracked by the video analytics are displayed on a map. Bosch Security Systems B.V. 2024-02 | V01 | DOC User manual...
This is useful indoor light sources and for colored LED light illumination. – Standard auto mode allows the device to continually adjust for optimal color reproduction in an environment with natural light sources. 2024-02 | V01 | DOC Bosch Security Systems B.V. User manual...
A low (negative) value means that the device switches to monochrome at a lower light level. A high (positive) value means that the device switches to monochrome at a higher light level. Bosch Security Systems B.V. 2024-02 | V01 | DOC User manual...
Temporal noise filtering Adjusts the Temporal noise filtering level between -15 and +15. The higher the value, the more noise filtering. 2024-02 | V01 | DOC Bosch Security Systems B.V. User manual...
Ideal for encoding on a DSL uplink where bit rate limitations are critical. Profile 8 SD 3G Optimized Ideal for encoding on a 3G uplink where bit rate limitations are critical. (Only applicable to 5MP models) Bosch Security Systems B.V. 2024-02 | V01 | DOC User manual...
The Active profile follows the scheduled profiles under Recording Profiles. Please refer to section Recording Profiles. This behavior is only applicable when using Bosch recording solutions, including edge recording or VRM recording. Third-party recording solutions might use the Non-recording profile.
SD cards are the ideal solution for shorter storage times and temporary recordings. They can be used for local alarm recording or to improve the overall reliability of video recording. For long-term authoritative images use an appropriately sized iSCSI system. Bosch Security Systems B.V. 2024-02 | V01 | DOC User manual...
An iSCSI target storage device can only be associated with one user. If a target is being used by another user, ensure that the current user no longer needs the target before decoupling that user. 2024-02 | V01 | DOC Bosch Security Systems B.V. User manual...
Select the encoder profile setting that is to be used with stream 1 and 2 when recording. This selection is independent of the selection for live stream transmission. (The properties of the encoder profiles are defined on the Encoder Streams page.) Bosch Security Systems B.V. 2024-02 | V01 | DOC User manual...
Page 38
Select the alarm type that is to trigger an alarm recording: – Analysis alarm Select the Virtual alarm sensors that are to trigger a recording, via RCP+ commands or alarm scripts, for example. 2024-02 | V01 | DOC Bosch Security Systems B.V. User manual...
Click a profile. Click Rename. Enter the new name and click Rename again. Recording status The graphic indicates the recording activity. An animated graphic is displayed when recording is taking place. Bosch Security Systems B.V. 2024-02 | V01 | DOC User manual...
Enter the interval in seconds at which the images are sent to an FTP server. Enter zero for no images to be sent. Target Select the target account for JPEG posting. 2024-02 | V01 | DOC Bosch Security Systems B.V. User manual...
– A warning through the Video Management System If a SD card is not installed, ‘SD card not found’ is shown. Notice! Bosch recommends the use of industrial micro SD cards with health monitoring. Alarm 5.6.1 Alarm Connections In the event of an alarm, the unit can automatically connect to a pre-defined IP address. The unit can contact up to ten IP addresses in the order listed until a connection is made.
Page 42
Configure and activate encryption for media data (such as video, metadata or audio when available) on the Encryption page (encryption is only available if the appropriate license is installed). Click Set to apply the changes. 2024-02 | V01 | DOC Bosch Security Systems B.V. User manual...
Detection of movement can be used to trigger an alarm and to transmit metadata. Various VCA configurations can be selected and adapted to your application, as required. Configure the VCA setting in the Bosch Configuration Manager. 5.6.3 Alarm Email Alarm states can be documented by e-mail.
Network Notice! Bosch recommends the use of industrial micro SD cards with health monitoring. 5.7.1 Network Services This page shows an overview of all available network services. Use the checkbox to activate or deactivate a network service.
Page 45
RCP+ port 1756 Activating RCP+ port 1756 allows unencrypted connections on this port. To allow only encrypted connections, set the Off option to deactivate the port. Bosch Security Systems B.V. 2024-02 | V01 | DOC User manual...
The device can receive data from an external TCP sender, for example an ATM or POS device, and store it as metadata. Select the port for TCP communication. Select Off to deactivate the function. Sender IP address Enter a valid Sender IP address. 2024-02 | V01 | DOC Bosch Security Systems B.V. User manual...
The SNMP engine ID field also appears, indicating the unique identifier of the SNMP entity. User name Enter the appropriate user name. Authentication protocol Select the appropriate authentication protocol: None, MD5, or SHA1. Authentication password Bosch Security Systems B.V. 2024-02 | V01 | DOC User manual...
To do this, check the box and enter the multicast address. Multicast Address Enter a valid multicast address to be operated in multicast mode (duplication of the data stream in the network). 2024-02 | V01 | DOC Bosch Security Systems B.V. User manual...
Enter the IPv4 address that you want to allow or block Mask 1 / 2 Enter the subnet mask for the appropriate IPv4 address. Click Set to apply the changes. Bosch Security Systems B.V. 2024-02 | V01 | DOC User manual...
Reconnecting in ... seconds. When the upload is completed successfully, the device reboots automatically. To save the camera settings: Click Download. A dialog box appears. Enter a password to protect the configuration file. 2024-02 | V01 | DOC Bosch Security Systems B.V. User manual...
Use the dropdown menu to select the Number of displayed entries to be listed in the current tab. Event Logging Current log level Select the level of event for which to display log entries or to log. Bosch Security Systems B.V. 2024-02 | V01 | DOC User manual...
This window is for information only and cannot be modified. Keep this information at hand when seeking technical support. Select the text on this page with a mouse and copy it so that it can be pasted into an e-mail if required. 2024-02 | V01 | DOC Bosch Security Systems B.V. User manual...
Search again for the IP address. Access the camera using the web browser. Set the initial password for the camera. Remove the camera bubble to access the reset button. Bosch Security Systems B.V. 2024-02 | V01 | DOC User manual...
– Repair & Exchange – Product Security Bosch Building Technologies Academy Visit the Bosch Building Technologies Academy website and have access to training courses, video tutorials and documents: www.boschsecurity.com/xc/en/support/training/ 2024-02 | V01 | DOC Bosch Security Systems B.V. User manual...