Download  Print this page

Mio Video I/o Port Control - Brother HL-1050 Technical Reference Manual

Laser printer.
Hide thumbs
   
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496

Advertisement

8/2/2010
If the key is [RENAME], this command allows the printer to change the name field of the AppleTalk name
binding protocol.
<ESC>&b#WRENAME<sp>printername
printername should be specified with 1 to 31 characters.
The characters $00 to $FF (except for $00, @, :, *, =, $C5) can be used for the printername.
$00 is used as the terminator.
If invalid characters are used, this command is ignored.
If the [key] is set to [JOB], this command changes the current job name.
<ESC>&b#WJOB<sp>jobname
All characters from $00 to $FF can be used for the jobname.
jobname can have a maximum of 127 characters.
If the [key] is set to [TYPE], this command allows the printer to change the type field of the AppleTalk
name binding protocol.
<ESC>&b#WTYPE<sp>devicetype
devicetype should be specified with 1 to 31 characters.
The characters $00 to $FF (except for $00, @, :, *, =, $C5) can be used for the devicetype.
$00 is used as the terminator.
If invalid characters are used, this command is ignored.

7.4.11. MIO video I/O port control

The HL-1660e and 2060 printers have only the "VSREQ" signal for vertical synchronization that can be sent to
the MIO port. This causes a short delay to the actual printing start after sending the VSREQ signal if the video
controller is processing an interrupt. This delay causes an incorrect vertical printing position. To avoid the
problem, the following command is useful.
EscCR!12340M
Laser diode video interface port of the MIO port is closed.
EscCR!12341M
Laser diode video interface port of the MIO port is opened.
EscCR!12342M
Laser diode video interface port of the MIO port is opened and the print start command is sent to the printer
engine immediately after sending the VSREQ signal.
(27)(13)(33)(49)(50)(51)(52)(48)(77)
<1Bh><0Dh><21h><31h><32h><33h><34h><30h><4Dh>
(27)(13)(33)(49)(50)(51)(52)(49)(77)
<1Bh><0Dh><21h><31h><32h><33h><34h><31h><4Dh>
(27)(13)(33)(49)(50)(51)(52)(50)(77)
<1Bh><0Dh><21h><31h><32h><33h><34h><32h><4Dh>
CHAPTER 2 "PCL" - 100

Advertisement

Table of Contents

   Related Manuals for Brother HL-1050

Comments to this Manuals

Symbols: 0
Latest comments: