Advertisement
Available languages
Available languages
(A-5
TM
INSTALLATION INSTRUCTIONS continued from page 5-E A-5
4) Notice how
battery wires from
E
inside lower receiver
are in slot
N
beside top of
G
armature pin
and the position
L
of the armature pin
.
I
To replace the battery, remove
S
old battery from inside the E-Grip
wires, carefully take it out. If you turn the receiver upside down the armature
H
pin
may come out, this is ok, just be sure to replace it.
remove battery clip
from old battery.
5) Carefully attach battery clip
terminals only fit one way in clip.
6) Make sure battery wires coming out of lower receiver are in slot
beside the armature pin
.
7) Make sure armature pin is properly positioned
and slides freely up and down.
8) Insert attached battery
bottom first
with clip wires facing the back of the
receiver
and to the right
NOTE: Make sure battery wires are not sitting on shelf
where the trigger assembly will rest.
9) Insert Trigger Assembly
insert the safety from the left
10) Visually inspect E-GRIP
trigger assembly
and battery installed
should look like this.
Check that the trigger
assembly is intact
with
no gaps
; and the safety is in the "SAFE"
(pushed to the right and red not showing) position
11) Attach Lower to Upper Receiver
front push pin hole
with upper receiver hole
grip to align upper & lower push pin hole
two lower receiver push pins
12) Attach Tank Adapter to E-Grip
lower receiver.
Slide tank adapter
Insert receiver bolt
and tighten.
Installation is complete, continue on page 7-E - OPERATING
INSTRUCTIONS.
TM
)
lower receiver. Do not jerk it out by the
TM
to new battery. NOTE: battery
in lower receiver
into lower receiver
.
and line up safety holes
to hold the trigger assembly in place.
TM
lower receiver, a top view with the
.
Align the E-Grip
lower receiver
TM
then gently rock rear of
.
With holes aligned, insert
and
to attach.
TM.
Remove receiver bolt
into lower receiver and align holes;
6-E A-5
TM
OPERATING INSTRUCTIONS
With the kit installation complete, read and follow these supplemental operating
instructions to the owner's manual FOR TIPPMANN A-5
98 CUSTOM
"EQUALIZER
marker. Keep these instructions with your marker owner's manual. Eye protection
designed for paintball use must be worn by the user and any person within range.
READ EACH STEP COMPLETELY BEFORE PERFORMING STEP:
STEP 1: Prepare the marker for safety before any programming:
Carefully
I N S TA L L T H E A I R S U P P LY A N D L O A D T H E H O P P E R W I T H
PAINTBALLS ONLY AFTER YOU:
HAVE THE BARREL SLEEVE INSTALLED;
HAVE THE SAFETY IN THE "SAFE" POSITION;
HAVE SUCCESSFULLY INSTALLED THE BATTERY AND
ARE FAMILIAR WITH THE E-TRIGGER
2: AND STEP 3:).
STEP 2: NORMAL OPERATION:
TOURNAMENT LOCK: Because the E-Trigger board requires a tool to
turn it on and off, no tournament lock is necessary for competition paintball.
1) To Turn ON the E-Trigger to normal operation - Ready To Fire:
Without holding the trigger: Use a small object
like an allen wrench to
button
for 1/2 second and then release the
power button. The LED
Orange for 2 seconds, flash once (green in A-5s or
red in 98s) and then light solid Green to show
normal operation - "Ready To Fire" mode.
• Your E-Trigger is now ready to fire in the SEMI-AUTO = 1 pull / release
of the trigger fires 1 time (Factory set Default Firing Mode).
NOTE: If pressing the power button failed to turn on LED light, see
troubleshooting on page 8-E.
2) To turn OFF the E-Trigger electronics.
button for 2 seconds as the LED turns solid Red, then release the Power
Button and the LED will turn OFF. NOTE: The trigger electronics are set to
shut-off automatically after a prolonged period of inactivity (120 minutes).
NOTE: The E-Trigger Low Battery Indicator feature: the "Ready To Fire" solid
Green LED will turn to blinking red when the battery is low and needs replaced.
from
3) To select a new firing mode:
1) Turn ON the E-Trigger to normal operation (solid Green LED - Ready
To Fire) as instructed in step 1) above.
2) Press / hold the power button in one time for more than 1/4 but less
than 2 seconds and release the power button.
TM
OR 98 CUSTOM PRO
TM
WITH E-TRIGGER
TM
LED BOARD INSTALLED before attempting to operate this
WARNING
TM
NORMAL OPERATION (STEP
press and hold the power
should light solid
7-E
(Custom
TM
or A-5
E
WITH E-GRIP
TM
,
TM
TM
marker with the
N
G
L
I
S
H
Power
Button
LED
Press and hold the power
Count the LED Orange
TM
)
(continued on page 8-E)
Advertisement
