Sharp AR-5127 Service Manual page 64

Operation/procedure
By setting the message No., the signal is sent to the line and the
speaker of the body. (The signal is continuously sent until the interrup-
tion command is provided by pressing the [BACK] key.)
The signal send level can be selected from 0dB or the soft SW set
value. However, the level setup is not required for 01, 31 - 35, the
selection may does not appear. After completion of the mode, the sig-
nal send level is returned to the soft SW set value before execution of
the mode.
Signal
Send signal
number
01 Signal not send
26 7EH Flag signal
27 to 30 Tone signal
31 Pseudo-ringer sound
([ON HOOK] key ON)
32 Voice message (no sound)
Under the state where the ring back
tone can be sent to the line, keep
the sound composition IC volume to
0.
33 Ring back tone (no sound)
Under the state where the ring back
tone can be sent to the line, keep
the G/A volume to 0.
34 Dial pulse (make)
Maintain the make state with
keeping the condition to be able to
send to the dial pulse line.
35 Dial pulse (break)
Maintain the break state with
keeping the condition to be able to
send to the dial pulse line.
Other than FFH
the above
Note: Executable only when the FAX is installed.
66-6
Purpose Adjustment/Setting/Check
Function Printing the confidential password
(Purpose)
Operation/procedure
The confidential ID table (confidential BOX numbers, confidential BOX
names, and confidential password) is printed.
The confidential data of My company mode is printed separately.
Note: Executable only when the FAX is installed.
66-7
Purpose Adjustment/Setting/Check
Function Print the screen memory contents
(Purpose)
Operation/procedure
Used to input all image data (including confidential reception data,
remote send image, not-sent image) stored in image memory of the
FAX section.
The output image is remained even after outputting.
Note: Executable only when the FAX is installed.
66-8
Purpose Adjustment/Setting/Check
Function Voice Message send
(Purpose)
Operation/procedure
By setting the message No., the sound message is sent to the line and
the speaker of the body. (The message is repeated until the interrup-
tion command is provided by pressing the [BACK] key.)
Message
number
Send level
Selection menu
None
Yes
Yes
None Message No. 4 can be heard by an external telephone speaker.
Note: Executable only when the FAX is installed.
None
66-10
Purpose
Function
(Purpose)
None
Operation/procedure
Used to clear all image data (including confidential reception data)
stored in image memory of the FAX section.
1: 0dB
The management table is also cleared (initialized) at the same time.
2: Soft SW
Note: Executable only when the FAX is installed.
66-11
1: 0dB
2: Soft SW Purpose
Function
(Purpose)
Yes
Operation/procedure
By setting the signal number, the specified signal is delivered to the
line at the speed of 300bps. (The signal is continuously sent until the
interruption command is provided by pressing the [BACK] key.)
The signal send level can be selected from 0dB or the soft SW set
value.
The signal send level is returned to the soft SW set value before exe-
cution of the mode after completion of the mode.
Number
1
2
3
Note: Executable only when the FAX is installed.
66-13
Purpose
Function
(Purpose)
Related soft SW SW53-1 to 4 (DTMF high group end level)
Operation/procedure
The send test of dial pulse and DTMF signal is performed and the
make time adjustment of dial pulse and the DTMF signal send level
adjustment are performed if necessary.
1. Dial pulse (10pps) send test
2. Dial pulse (20pps) send test
• Used to set the make time. By performing the test, the registered dial
pulse of max. 100 digits can be sent from the line.
• When "*" and "#" are included in the registered dial number, they are
disregarded and the number is not processed as a dial.
AR-5127 SIMULATION 8 - 36
Voice message
1 "Hold the line a minute, please send fax."
(TEL/FAX voice response)
2 "Hold the line a minute."
(TEL/FAX voice response)
3 "Not around here, please send fax."
(TEL/FAX voice response)
4 "Ding Dong"
(Sound delivered when switching to remote reception)
Adjustment/Setting/Check
Image data memory clear
Adjustment/Setting/Check
300bps signals send
Signal
No signal (CML ON)
11111
11110
Adjustment/Setting/Check
Send test and adjustment of the dial pulse and
DTMF signal.
SW53-5 to 8 (DTMF low group send level)
SW67-1 to 4 (DP 10PPS make time)
SW67-5 to 8 (DP 10PPS make time)
Number Signal
4 00000
5 010101
6 00001