Sharp AR-5127 Service Manual page 34

Transport selection gate solenoid (R)
8:OGSLR
Transport selection gate solenoid (L)
9:OGSLL
Rear edge plate drive solenoid
10:JGSL1
Upper alignment plate drive solenoid
11:JGSL2
Shutter drive solenoid
12:SHTSL
Paper exit roller clutch
13:T2SCL
Paper holding solenoid
14:STGSL
The finisher main motor operates for 10sec, the staple motor 5 times,
the tray lift-up motor one reciprocating operation, other motors max. 20
reciprocating operations from the home position, the solenoid repeats
500msec ON and 500msec OFF 20 times.
The staple operation motor operates only when there is no cartridge
installed.
Note: Executable only when the finisher is installed.
3-6
Purpose Adjustment
Function Used to adjust the finisher jogger position.
(Purpose)
Section Sorter/Finisher
Item Operation
Operation/procedure
After the paper size is set, the side guide plate and the rear guide plate
are set.
Shifts to the specified paper size position.
(Initial screen) (Input screen)
Sim3-6 JOGGER ADJ.
Sim3-6 JOGGER ADJ.
1:PAPER SIZE
2:JOGGER POS X
2:JOGGER POS X
3:JOGGER POS Y
1
EXEC [ 0- 99]
Display items
Paper size
1:PAPER SIZE
(1:A3, 2:A4, 3:B4, 4:B5,
5:A4R, 6:WLT, 7:LT,
8:LG, 9:FC, 10:LTR,
11:8K, 12:16K)
Side guide plate
2:JOGGER POS X
Rear edge guide plate
3:JOGGER POS Y
There are 6 adjustment values for the side guide plate, and 12 for the
rear guide plate. The adjustment position is determined from the table
below according to the paper size.
Example: When the side guide plate value is adjusted in A3, the same
adjustment is made in A4. (Value 1 in the table)
Side guide plate
Paper size
adjustment value number
A3 1
A4 1
B4 3
B5 3
A4R 5
WLT 2
LT 2
LG 4
FC 4
LTR 4
8K 6
16K 6
Note: Executable only when the finisher is installed.
(Executing screen)
Sim3-6 JOGGER ADJ.
50 2:JOGGER POS X
50 EXEC [ 0- 99]
Setting
Content Default
range
1-12
1-99
Adjustment value number
of the rear edge guide
plate
2
9
3
10
6
1
8
4
5
7
11
12
AR-5127 SIMULATION 8 - 6
3-7
Purpose Adjustment
Function Used to adjust the offset tray operations.
(Purpose)
Item Operation
Operation/procedure
(Initial screen)
Sim3-7 OFFSET ADJ.
1:PAPER PUSH TMG 50
2:PAPER OUT DOWN 1
3:STAPLE UP
1/2
Display items
1:PAPER PUSH TMG Paper holder
2:PAPER OUT DOWN Tray descending
50
50
3:STAPLE UP
50
4:STAPLE DOWN
5:OFFSET INI.POS Offset tray shift
Note: Executable only when the finisher is installed.
(Input/Selection screen) (Executing screen)
Sim3-7 OFFSET ADJ.
1:PAPER PUSH TMG 50
6
[ 34- 66] 50
Installation
Content
descending timing in
non-staple
Used to adjust the descending timing of the
paper holder lever before lift-up operation
after paper exit or offset operation. (The
paper holder lever prevents against paper
shift in paper top surface detection and paper
stacking.)
distance after non-
staple paper exit
Used to adjust the offset tray descending
distance after non-staple paper exit.
The descending distance is the relative
distance from the non-staple standby
position.
Tray lift distance
before staple paper
exit
The height of the tray standby position in
stapling is changed for that in non-stapling to
improve stacking capacity in stapling. (The
relative distance for the height of the tray
standby position in non-stapling is set.)
Tray descending
distance after staple
paper exit
Used to adjust the offset tray descending
distance after staple paper exit.
The descending distance is the relative
distance from the non-staple standby
position.
position adjustment
Used to shift the offset tray to the shipment
position or the disassembly position.
The offset tray is shifted to the specified
counter position.
(In the case of 0 - 94 (Shipment position: 13))
1) Initialize the offset tray normally.
2) The tray descends to the parameter posi-
tion + 1 pulse position.
3) The tray lifts up to the specified parame-
ter position.
(Disassembly position: 94 - 99)
1) The tray descends to the bottom.
* If there is some paper in the offset tray, the
tray cannot descend to the specified posi-
tion. Check to insure that there is no paper
in the tray before execution.
Sim3-7 OFFSET ADJ.
5:OFFSET INI.POS 13
EXEC [ 0- 99] 13
Default
range
34-66 50
0-12 1
0-12 6
0-12 6
0-99 13