Sharp AR-5127 Service Manual page 35

3-11
Purpose Operation test/check
Function Used to check the operation of the shifter.
(Purpose)
Item Operation
Operation/procedure
[Selection 1]
Select with the 10-key.
(Initial screen) (Executing screen)
Sim3-11 SHIFTER CHK Sim3-11 SHIFTER CHK
1:F-R 1:F-R
2:HP CHECK 2:HP CHECK
1
Reciprocating operation
1:F-R
Home position check
2:HP CHECK
[Selection 2]
(Input/Selection screen)
Sim3-11 SHIFTER CHK
SFTHP
[ ]:R [ ]:HP [ ]:F
Shifter home position (At detection, highlighted)
SFTHP:
[ ] key Shifts the position toward R side by the specified steps.
[ ] key Shifts the position toward F side by the specified steps.
[ ] key Shifts to the home position.
4
4-2
Purpose Operation test/check
Function Used to check the operation of sensor and detector in
(Purpose) the option tray and the related circuit.
Section Paper feed
Item Operation
Operation/procedure
The operating states of the sensor and the detector are displayed.
The active sensors and detectors are highlighted.
Sim4-2 SENSOR CHECK
PED2 LUD2 PFD2 CD2
PED3 LUD3 PFD3 CD3
PED4 LUD4 PFD4 CD4
DSWR2 DSWR3 DSWR4
2nd cassette paper empty sensor
PED2
2nd cassette paper upper limit detection sensor
LUD2
2nd cassette paper pass sensor
PFD2
2nd cassette empty sensor
CD2
3rd cassette paper empty sensor
PED3
3rd cassette paper upper limit detection sensor
LUD3
3rd cassette paper pass sensor
PFD3
3rd cassette empty sensor
CD3
4th cassette paper empty sensor
PED4
4th cassette paper upper limit detection sensor
LUD4
4th cassette paper pass sensor
PFD4
4th cassette empty sensor
CD4
3rd cassette right door detection sensor
DSWR3
2nd cassette right door detection sensor
DSWR2
4th cassette right door detection sensor
DSWR4
Note: Execution is possible only when the option cassette is installed.
EXEC 1
AR-5127 SIMULATION 8 - 7
4-3
Purpose Operation test/check
Function Used to check the operation of the load in the option
(Purpose) tray and the control circuit.
Section Paper feed
Item Operation
Operation/procedure
Select the load to check with the 10-key.
During execution of load operation, [EXEC] is highlighted.
Pressing the [BACK] key under this state interrupts the operation.
(Initial screen) (Executing screen)
Sim4-3 OUTPUT CHECK Sim4-3 OUTPUT CHECK
1:LUM2 4:TRC2 7:CPFC3
2:CPFC2 5:DM 8:CPFS3
3:CPFS2 6:LUM3 9:TRC3
1/2 EXEC
2/2
2nd cassette lift-up motor
1:LUM2
2nd cassette pick-up solenoid
2:CPFC2
2nd cassette paper feed clutch
3:CPFS2
2nd cassette transport roller clutch
4:TRC2
2nd cassette paper transport motor (3rd cassette paper
5:DM
transport motor)
3rd cassette lift-up motor
6:LUM3
3rd cassette pick-up solenoid
7:CPFC3
3rd cassette paper feed clutch
8:CPFS3
3rd cassette transport roller clutch
9:TRC3
4th cassette lift-up motor
10:LUM4
4th cassette pick-up solenoid
11:CPFC4
4th cassette paper feed clutch
12:CPFS4
The motor for 10sec, the solenoid ON for 500msec, OFF for 500msec.
The lift-up motor operates only when the tray is opened. (20 times)
Note: Execution is possible only when the option cassette is installed.
5
5-1
Purpose Operation test/check
Function Used to check the operation of the display, LCD in the
(Purpose) operation panel, and control circuit.
Section Operation (screen/operation)
Item Operation
Operation/procedure
The LCD is displayed as follows. (All LED's are ON.)
(Initial screen)
With the upper half section highlighted,
Sim5-1 LCD/LED CHK.
contrast changes "Standard
every 2sec.
(6 sec later)
With the lower half section highlighted, contrast
Sim5-1 LCD/LED CHK.
changes "Standard
2sec.
(6 sec later)
The back light changes in the sequence of
Sim5-1 LCD/LED CHK.
"OFF
seconds.
10:LUM4
11:CPFC4
12:CPFS4
EXEC 8
MAX MIN." in
MAX MIN." in every
Red Yellow Green" every 2