Sharp AR-5127 Service Manual page 36

5-2
Purpose Operation test/check
Function Used to check the operation of the heater lamp and the
(Purpose) control circuit.
Section Fixing (Fusing)
Item Operation
Operation/procedure
Press the [OK] key.
ON/OFF operation of the heater lamp is repeated 5 times in an interval
of 500ms.
(Initial screen) (Executing screen)
Sim5-2 HEATER LAMP Sim5-2 HEATER LAMP
PRESS OK KEY EXEC
5-3
Purpose Operation test/check
Function Used to check the operation of the copy lamp and the
(Purpose) control circuit.
Section Optical (Image scanning)
Item Operation
Operation/procedure
Press the [OK] key.
The copy lamp lights up for 10 sec.
(Initial screen) (Executing screen)
Sim5-3 COPY LAMP Sim5-3 COPY LAMP
PRESS OK KEY EXEC
When 10 sec passed, the copy lamp is turned OFF.
6
6-1
Purpose Operation test/check
Function Used to check the operation of the loads (clutches and
(Purpose) solenoids) in the paper transport system and the
control circuit.
Section Paper transport (Discharge/Switchback/Transport)
Item Operation
Operation/procedure
The names of the loads which can be operated are displayed. Select
the load to be checked with the 10-key.
(Initial screen) (Executing screen)
Sim6-1 OUTPUT CHECK
Sim6-1 OUTPUT CHECK
1:LUM1 4:MPFS
7:OGS
2:CPFC1 5:RRC
8:LUM2
3:CPFS1 6:PSPS
9:CPFC2
1/2 EXEC
2/2
1st cassette lift-up motor
1:LUM1
1st cassette pick-up solenoid
2:CPFC1
1st cassette paper feed clutch
3:CPFS1
Manual feed pick-up solenoid
4:MPFS
Resist roller clutch
5:RRC
Separation pawl solenoid
6:PSPS
Paper exit gate switching solenoid
7:OGS
2nd cassette lift-up motor
8:LUM2
2nd cassette pick-up solenoid
9:CPFC2
2nd cassette paper feed clutch
10:CPFS2
EXEC
EXEC
10:CPFS2
11:TRC2
EXEC 8
AR-5127 SIMULATION 8 - 8
2nd cassette transport roller clutch
11:TRC2
3rd cassette lift-up motor
12:LUM3
3rd cassette pick-up solenoid
13:CPFC3
3rd cassette paper feed clutch
14:CPFS3
3rd cassette transport roller clutch
15:TRC3
4th cassette lift-up motor
16:LUM4
4th cassette pick-up solenoid
17:CPFC4
4th cassette paper feed clutch
18:CPFS4
The motor for 10sec, the solenoid ON for 500msec, OFF for 500msec.
(20 times)
The lift-up motor operates only when the tray is opened.
6-2
Purpose Operation test/check
Function Used to check the operation of each fan motor and its
(Purpose) control circuit.
Section Others
Item Operation
Operation/procedure
The names of the loads which can be operated are displayed. Select
the load to be checked with the key.
(Initial screen) (Executing screen)
Sim6-2 FAN MOTOR
Sim6-2 FAN MOTOR
1:VFM
1:VFM
2:DCFM&DCFM2
2:DCFM&DCFM2
3:VFM&DCFM&DCFM2
3:VFM&DCFM&DCFM2
EXEC 2
The selected fan motor is highlighted and it rotates for 10sec.
Only the fusing fan operates
1:VFM
Power cooling fan, power cooling fan 2
2:DCFM&DCFM2
operations
Fusing fan, power cooling fan, and power
3:VFM&DCFM&DCFM2
cooling fan 2 are operated at the same time.
7
7-1
Purpose Setting/Operation test/check
Function Used to set the aging operation conditions.
(Purpose)
Item Operation
Operation/procedure
Select with the 10-key.
Sim7-1 AGING SET.
1:AGING 4:INTERVL
2:MISFEED 5:WARMUP
3:FUSING 6:DV CHK.
2
Aging enable/disable setting
1:AGING
Jam detection enable/disable setting
2:MISFEED
Fusing operation enable/disable setting
3:FUSING
The fusing temperature is not controlled. The heater is
not turned ON.
Intermittent setting (Valid only when set to AGING.)
4:INTERVL
Warm-up save setting
5:WARMUP
The machine goes into the ready state only by
shading, disregarding fusing and process control.
After going into the ready state, normal control is
performed.
Developing unit detection enable/disable setting
6:DV CHK.
Press [CA] key, and the simulation will be terminated and copying will
be made with the set contents.
EXEC 2