Sharp AR-5127 Service Manual page 33

(Initial screen) (Input/Selection screen) (Executing screen)
Sim2-1 SPF AGING
Sim2-1 SPF AGING
115%
115% A3 1SIDE
100%
100% 2SIDE
86%
86%
ZOOM <100%>
ZOOM <100%> 0
The magnification ratio can be selected in the range of 50% – 200% in
9 steps with keys.
(AB series) 50 70 81 86
(Inch series) 50 64 77 95
The scan counter is displayed during execution.
Magnification ratio 50% to 200%
Default 100%
Document size Varies depending on the destination.
Single/duplex Selectable only when RSPF is installed, fixed
(single) for SPF.
Set number of times 1 to 999 (0: Continuous operation)
Note: Executable only when the SPF/RSPF is installed.
2-2
Purpose Operation test/check
Function Used to check the operation of sensors and detectors
(Purpose) in the SPF unit and the related circuit.
Section SPF
Item Operation
Operation/procedure
The operations of sensors and detectors in the SPF section are dis-
played.
The active sensors and detectors are highlighted.
EMPS
Sim2-2 SENSOR CHECK
EMPS DLS1 DLS2 DLS1
DWS1 DWS2 DWS3
DLS2
FGOD DFD RDD
DWS1
OPCLS
DWS2
DWS3
FGOD
DFD
RDD
OPCLS
Note: Executable only when the SPF/RSPF is installed.
2-3
Purpose Operation test/check
Function Used to check the operation of the loads in the SPF
(Purpose) unit and the control circuits.
Section SPF
Item Operation
Operation/procedure
The names of the loads which can be operated are displayed. Select
the load to be checked with the 10-key.
(Initial screen) (Executing screen)
Sim2-3 OUTPUT CHECK
Sim2-3 OUTPUT CHECK
1:DTM-F 4:CLH 1:DTM-F
2:DTM-R 5:GSOL 2:DTM-R
3:DFSOL 6:RSOL 3:DFSOL
EXEC 2
SPF motor forward rotation
1:DTM-F
SPF motor reverse rotation
2:DTM-R
SPF document pick-up solenoid
3:DFSOL
SPF document exit transport clutch
4:CLH
RSPF document exit gate solenoid
5:GSOL
RSPF document pressure solenoid
6:RSOL
The motor for 10sec, the solenoid ON for 500msec, OFF for 500msec.
(20 times)
Note: Executable only when the SPF/RSPF is installed.
Sim2-1 SPF AGING
A3 1SIDE
115% A3 1SIDE
2SIDE
100% 2SIDE
86%
EXEC
ZOOM <100%>
100 115 122 141 200
100 121 129 141
Empty sensor
Tray length sensor (small)
Tray length sensor (large)
Tray width sensor (small)
Tray width sensor (middle)
Tray width sensor (large)
Paper feed cover sensor
Document entry detection sensor
Document exit sensor
Book sensor
4:CLH
5:GSOL
6:RSOL
EXEC 2
AR-5127 SIMULATION 8 - 5
3
3-2
Purpose Operation test/check
EXEC
Function Used to check the operation of sensor and detector in
(Purpose) the finisher and the related circuit.
Section Sorter/Finisher
Item Operation
200
Operation/procedure
Used to display the operations of sensors and detectors in the finisher
section.
The active sensors and detectors are highlighted.
Sim3-2 SENSOR
INPD FWPS JGHP1
JGHP2 JGPD T1OD
T1PF PGOP T2OD
OFHP T2UP T2DN
Finisher paper entry sensor
INPD
Paper width sensor
FWPS
Side guide plate HP sensor
JGHP1
Rear edge plate HP sensor
JGHP2
Tray paper empty sensor
JGPD
1st tray exit sensor
T1OD
1st tray paper full sensor
T1PF
JAM processing PG open/close detection sensor
PGOP
2nd tray transport sensor
T2OD
Offset HP sensor
OFHP
Tray position sensor (upper)
T2UP
Tray position sensor (lower)
T2DN
Tray jam processing interlock
JGDSW
Lift-up drive control sensor
EVRE
Staple HP sensor
STHP
Self priming sensor
READY
Staple empty sensor
LSTS
Cartridge empty sensor
NCTS
Staple supply cover open/close sensor
STND
2nd tray upper surface sensor
T2PUD
Note: Executable only when the finisher is installed.
3-3
Purpose Operation test/check
Function Used to check the operation of the load in the finisher
(Purpose) and the control circuit.
Section Sorter/Finisher
Item Operation
Operation/procedure
The names of the loads which can be operated are displayed. Select
the load to be checked with the key.
(Initial screen)
Sim3-3 OUTPUT CHECK
1:JGM1 4:FM-1200
2:JGM2 5:EVM
3:FM-600 6:OFM
1/3 EXEC
During execution, [EXEC] is highlighted. Under this state, press the
[BACK] key to interrupt the operation.
Side guide plate drive motor
1:JGM1
Rear edge plate drive motor
2:JGM2
Finisher main motor (600dpi)
3:FM-600
Finisher main motor (1200dpi)
4:FM-1200
Tray lift-up motor
5:EVM
Tray offset motor
6:OFM
Staple operation motor
7:STM
1/2
(Executing screen)
Sim3-3 OUTPUT CHECK
7:STM 10:JGSL1
8:OGSLR 11:JGSL2
9:OGSLL 12:SHTSL
2/3 EXEC 8
Disabled