Sharp AR-5127 Service Manual page 61

51
51-1
Purpose Adjustment
Function Used to adjust the OPC drum separation pawl ON
(Purpose) time.
Section Image process (Photoconductor/Developing/Transfer/
Cleaning)
Item Operation
Operation/procedure
Enter the adjustment value with the 10-key and press the [OK] key, and
the entered value is registered.
(Initial screen) (Input screen)
Sim51-1 D/F TIMING
Sim51-1 D/F TIMING
2:1200dpi
1:600dpi 50
2:1200dpi 50
2 [ 1- 99]
Display items Setting range
1-99
1:600dpi
2:1200dpi
51-2
Purpose Adjustment
Function Used to adjust the contact pressure of paper onto the
(Purpose) resist roller in each section (copier paper feed section,
duplex paper feed section, SPF paper feed section).
(When the print image position varies greatly for the
paper or when a lot of paper jam troubles occur, the
adjustment is required.)
Section Paper transport (Discharge/Switchback/Transport)
Item Operation
Operation/procedure
Select the mode with the arrow keys, enter the adjustment value with
the 10-key, and press the [OK] key.
When the [START] key is pressed, a print is made and the display
returns to the mode selection menu.
(Initial screen) (Input screen)
Sim51-2 RESIST ADJ.
1:BYPASS 50
2:TRAY1 50
3:TRAY2 50
1/3 50
Display items Content
Manual feed
1:BYPASS
1st cassette
2:TRAY1
2nd cassette
3:TRAY2
3rd cassette
4:TRAY3
4th cassette
5:TRAY4
Back print
6:DUPLEX
SPF front
7:SPF(SIDE1)
surface
50
50
Default
50
Disabled
(Executing screen)
Setting
Default Remark
range
1-99 50 Tray selection:
Manual feed
cassette is
specified.
1-99 50 Tray selection:
1st cassette is
specified.
1-99 50 Tray selection:
2nd cassette is
specified.
1-99 50 Tray selection:
3rd cassette is
specified.
1-99 50 Tray selection:
4th cassette is
specified.
1-99 50 Tray selection:
Made by user.
1-99 50 Tray selection:
Made by user.
AR-5127 SIMULATION 8 - 33
Display items Content
SPF back
8:SPF(SIDE2)
surface
Setup of various copy conditions: Similar to the normal copy mode.
Use of [SPECIAL FUNCTION] key, [JOB STATUS] key, and [INTER-
RUPT] key is inhibited.
51-8
Purpose Setting
Function Used to set to disable the operation of the separation
(Purpose) pawl of the photoconductor drum.
Section Image process (Photoconductor/Developing/Transfer/
Cleaning)
Item Operation
Operation/procedure
Enter the adjustment value with the 10-key and press the [OK] key, and
the entered value is registered.
Sim51-8 D/F SETTING
DETACH FINGER 0
(0:ON
1:OFF)
[ 0- 1] 1
Display items Content
Enable
0:ON
Disable
1:OFF
51-9
Purpose Adjustment
Function Used to adjust ON/OFF timing of the separation
(Purpose) voltage.
Item Adjustment
Operation/procedure
Used to adjust ON/OFF timing of the separation voltage.
(Initial screen) (Input screen)
Sim51-9 SHV SETTING Sim51-9 SHV SETTING
1:SHV ON 50 1:SHV ON
2:SHV OFF 50
1 [ 1- 99]
Display
Content
items
Separation voltage ON timing
1:SHV ON
* Transfer V2ON reference
(synchronized with the
adjustment value of 50)
2:SHV OFF Separation voltage OFF timing
* Transfer V2OFF reference
(synchronized with the
adjustment value of 50)
Setting
Default Remark
range
Tray selection:
Made by user.
Setting range Default
0-1 0
50
50
Setting
Default
range
25-90 50
50-90 75